Moen 11 Installing Your Moen Tub/Shower Trim, Gasket on the back, Escutcheon provides a seal

3.5 E 3.5 Once the valve is secured in place,

Threaded Tub Spout Installation

English		remove the escutcheon screws
	G	(G) and the plaster ground (E).
		Keep the escutcheon screws (G)
		for installation of the escutcheon
		(F) and discard the plaster
		ground (E).
		3.6 Place product identification label
	Ensure cartridge	(Z) on back of escutcheon, make
		sure wall is clean, place the
	retainer clip is
		escutcheon (F) over the stop tube
	installed prior to
	escutcheon	(B) then re-install the screws (G).
	installation.	A gasket on the back of the
		escutcheon provides a seal
		against the wall.

4.3A	Tub Spout Installation
	S
	1
	Thread seal tape
	2
	x
	y

If this is a shower only installation, skip to step 4.4.

IPS (threaded) spouts are designed to screw onto a pipe with 1/2 inch male pipe threads. To determine the proper pipe length, measure from the inside elbow shoulder to the wall (y) and from the threaded adapter inside of the tub spout to the base of the tub spout (x), then add 1/4”. Place thread seal tape around the pipe threading and a sealant (plumbers putty or caulk) around the base of the pipe to

English

3.6

B

F

(y) + (x) + 1/4” = Pipe Length

To determine the proper pipe length, measure from the inside elbow

shoulder to the wall (y) and from the threaded adapter inside of the

tub spout to the base of the tub spout (x), then add 1/4”.

prevent leaking behind the wall.

Z 1

2 3

Slip Fit Tub Spout Installation

Cartridge Orientation

F

G

Go To Step 4.1

4.3B

No sharp edges/burrs on end of pipe.

1

4.4 NO

4. Installing Your Moen Tub/Shower Trim

S

C

D

4.1

1

2

4.2A

1

A

4.2B

1

A

OR	1
Not 2	5/32"	Slightly tighten
Included		set screw.
	Hex

	S
2	1

YES

H

Thread SealTape

H

3

Thread Seal Tape

2

H

3

OR

Thread Seal Tape

2

Some models may feature a slip fit installation with no threaded adapter in the tub spout. For these installa- tions, slip the tub spout onto pipe pointing up and slightly tighten the set screw. Rotate tub spout to final position and fully tighten set screw in place.

Now you are ready to attach the handle. Rotate so the notch at the end of the stem is facing down towards the drain. Insert the key stop (C) and the adjustable limit stop (D) into stop tube as shown.

I

I

For Lever Handles Installed with Plastic Handle Adapter (J)

Wrap thread seal tape around the threads of the shower arm (H) then screw the arm into the threaded connection in the wall.

If there is a rubber washer inside the threaded adapter on the shower- head, continue to step 4.2A. If there is no rubber washer, then proceed to step 4.2B.

4.2A Plastic Shower Ball Seal around the shower arm hole with sealant (caulk) then slide shower flange (A) over shower arm (H). Remove any debris from the shower arm to ensure proper flow. Then, simply thread showerhead (I) onto shower arm (H).

4.2B Metal Shower Ball Seal around the shower arm hole with sealant (caulk) then slide shower flange (A) over shower arm (H). Wrap thread seal tape around threads at bottom of shower arm (H). Remove any debris from the shower arm to ensure proper flow. Thread showerhead (I) onto shower arm (H).

4.5

D

J

K

If this is a lever handle that attaches with the lever handle adapter (J), attach the plastic handle adapter (J) to the car- tridge stem using the 1/2 inch adapter screw (K). Make sure the ridges on the back of the adapter (J) are to the left of the tab on limit stop (D).

L

Place the lever (L) on the lever handle adapter.

Other Possible Handle Type Installations

4.6

F

P

Place the knob handle

(P)– onto the cartridge - make sure the indicator on the knob is pointing down.

E8

E9