Electrolux FMV156DBE service manual Power Transformer Removal, Hood FAN Motor Removal, Re-install

Page 30
OUTER CASE REMOVAL

FMV156DBE

FMV156DSE

FMV156DQE

FMV156DCF

5.Pull the hood exhaust louver from the oven cavity by pushing the right and left tabs of the hood exhaust louver to remove.

6.Now, the hood exhaust louver is free.

Push

Hood exhaust louver

Tab (left )

Push

Tab (right)

REMOVAL OF OVEN FROM WALL (Two persons recommended to remove the oven)

1.

Disconnect the power supply cord, and uncoil the power supply cord.

2.

To discharge the high voltage capacitor, wait for 60

6.

While supporting the front of the oven, pull down the two

 

seconds.

 

(2) mounting levers and release the oven from the unit

3. Remove the turntable tray and support from the oven

 

mounting plate.

 

cavity.

7.

Pull the power cord out of the wall cabinet and remove

4.

If the exhaust damper assembly is installed, remove the

 

the oven.

 

one (1) screw holding the exhaust damper assembly to

8.

The oven is now free and can be placed on the work

 

the rear stay, and remove the exhaust damper assembly

 

surface selected for servicing the oven.

 

by sliding it backward.

9.

Installation is the reverse of this procedure.

5.Remove the two (2) screws holding the oven (outer case cabinet) to the top cabinet.

Remove the oven from the wall, referring to "removal of oven from wall" and proceed as follows;

1.Disconnect the power supply cord.

2.Open the door and block it open.

3.To discharge the high voltage capacitor, wait for 60 seconds.

4.Remove four (4) screws holding the rear stay to the hood fan motor or the oven, and remove it.

5.Remove the six (6) screws from the rear of the outer case cabinet and one (1) screw at front.

6.Slide the outer case cabinet back about 1 inch (3 cm) to free it from retaining clips on the cavity face plate.

7.Disconnect the three (3) pin connector of the power supply cord from the wiring harness and remove the

power supply cord together with the outer case.

8.Nip the cord bushing with bushing pliers and release it from the outer case cabinet.

9.Remove the cord bushing and the power supply cord from the outer case cabinet.

10.Now, the power supply cord is free.

CAUTION: 1. Disconnect oven from power supply before removing outer case.

2.Discharge the high voltage capacitor before touching any oven components or wiring.

POWER TRANSFORMER REMOVAL

1.Disconnect the power supply cord, remove the oven from wall, and remove outer case. (Refer to procedure of "Removal of Oven from Wall" and "Outer Case Removal".) And proceed as follows.

2.Open the door and block it open.

3.To discharge the high voltage capacitor, wait for 60 seconds.

4.Remove three (3) screws holding the hood intake duct R to the oven cavity top plate, the oven cavity front flange and the fan duct. And remove the hood intake duct R.

5.Disconnect main wire harness from transformer.

6.Disconnect high voltage wire A from the transformer.

7.Disconnect filament leads of transformer from the magnetron and capacitor.

8.Remove two (2) screws holding the transformer to base plate R.

Re-install

1.Install by sliding the transformer on the base plate R with its primary terminals toward the outer case.

2.Secure the transformer with two (2) screws to base plate R.

3.Re-connect wire leads (primary and high voltage) to the transformer and filament leads of transformer to magnetron and high voltage capacitor. Refer to

"PICTORIAL DIAGRAM".

4.Re-install the hood intake duct R to the oven cavity top plate, the oven cavity front flange and the fan duct with three (3) screws.

5.Re-install the outer case and check that oven is operating properly.

CAUTION: Make sure the wire leads never touch the fan blade.

HOOD FAN MOTOR REMOVAL

1.

Disconnect the power supply cord and remove the oven from wall and remove outer case.(Refer to procedure of "Removal

 

of Oven from Wall" and "Outer case Removal")

seconds.

2.

Open the door and block it open.

4. Disconnect the 6-pin connector of the hood fan motor

3.

To discharge the high voltage capacitor, wait for 60

from the main wire harness located at the right edge of

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Table of Contents Over the Range Microwave Oven ModelsBefore Servicing When the testing is completed Dont Touch Before ServicingMicrowave Measurement Procedure RequirementsLeakage test Electrolux Product Specification General InformationOven Diagram Control Panel Operation Description of Operating SequenceVertical Venting Horizontal VentingRE-CIRCULATION Inside Venting Figure O-1. Oven Schematic-Off Condition Description and Function of Components FunctionsTroubleshooting Guide CK = Check / RE = Replace Procedure Component Test Letter Magnetron Assembly Test Microwave Output PowerPower Transformer Test Magnetron Temperature Fuse Test High Voltage Capacitor TestCavity Thermal CUT-OUT Test Primary Interlock Switch Test Procedure Component Test LetterTEMPERATURE, Replace Temperature Fuse Door Sensing SwitchMonitor Switch Test Secondary Interlock Relay RY2Procedure Hood Thermal CUT-OUT TestHood FAN Motor Test Before testing KEY Unit Test Relay Test1ST Stage 2ND Stage Foil Pattern on the Printed Wiring Board TestDefrost Center Test Level TimeOccurrence Cause or Correction RemovalSteps Occurrence Cause or Correction Procedure Component Test Letter Noise Filter Test Measuring Point Indication of OHM-METERTouch Control Panel Assembly Description of LSILSI Signal coming from touch key Signal to sound buzzer 2.0 kHzOUT Oven lamp, fan motor and turntable motor driving signal Signal similar to P46Hood motor driving signal Key strobe signalHood lamp driving signal Segment data signalShapes of Electronic Components Other PrecautionsServicing Servicing of Touch Control PanelComponent Replacement and Adjustment Procedure Hood Exhaust Louver RemovalPictorial Diagram Power Transformer RemovalRe-install Hood FAN Motor RemovalHood FAN Thermal CUT-OUT Removal Magnetron RemovalHigh Voltage Rectifier and High Voltage Capacitor Removal Thermal CUT-OUT Cavity RemovalInstallation Cooling FAN Motor RemovalSide View Positive lock connector Positive Lock Connector NO-CASE Type RemovalControl Panel ASSEMBLY, Control Unit and KEY Unit Removal Turntable MotorKey unit location Control Unit and KEY Unit RemovalDoor Replacementdoor Assembly Removal Door Assembly RE-INSTALLChoke Cover Door DisassemblyDoor Frame Assembly Latch SPRING, Latch Head and Door PanelDiagram PictorialFigure S-2. Power Unit Circuit LSI Unit Circuit Figure S-4. Printed Wiring Board Cabinet Parts Parts ListElectric Parts Control Panel PartsDoor Parts MiscellaneousSCREWS,NUTS, Washers and Other Oven and Cabinet Parts Control Panel Parts Door Parts Miscellaneous Packing and Accessories Non-replaceable itemsFMV156DBE FMV156DSE FMV156DQE FMV156DCF FMV156DBE FMV156DSE FMV156DQE FMV156DCF FMV156DBE FMV156DSE FMV156DQE FMV156DCF

FMV156DBE specifications

The Electrolux FMV156DBE is a modern and versatile microwave oven that combines sleek aesthetics with cutting-edge technology, making it a popular choice for contemporary kitchens. This model offers a range of advanced features designed to streamline cooking and enhance convenience while ensuring users can prepare meals efficiently.

One of the standout features of the Electrolux FMV156DBE is its powerful 1.6 cubic feet capacity, which provides ample space for cooking various dishes, from reheating leftovers to defrosting frozen goods. Its 1,000-watt power output allows for fast and efficient cooking, ensuring that food is heated evenly and thoroughly. The microwave also features multiple power levels, enabling users to customize cooking intensity based on their specific needs.

This model is equipped with the Sensor Cooking technology, which automatically adjusts cooking time and power based on the moisture released from the food. This intelligent feature helps to prevent overcooking or undercooking, delivering perfectly prepared meals every time. Additionally, the FMV156DBE includes a range of pre-programmed cooking settings that cater to different food types, further enhancing usability and efficiency.

Another notable aspect of the Electrolux FMV156DBE is its intuitive touch control panel, allowing for easy navigation through cooking options and settings. The illuminated LED display enhances visibility, making it simple to monitor cooking progress at a glance. The microwave also features a convenient kitchen timer and a clock function, adding to its overall functionality.

The microwave not only excels in cooking performance but also in design. It features a contemporary stainless-steel finish that adds a touch of elegance to any kitchen decor. The streamlined design ensures it can fit seamlessly into various kitchen layouts, while the built-in design options provide flexibility for installation.

Safety is also a priority with the Electrolux FMV156DBE, which includes a child lock feature, preventing unintended use by little hands. This quality makes it an ideal appliance for families with children.

In summary, the Electrolux FMV156DBE is a highly functional microwave oven that features advanced cooking technologies, an ample cooking capacity, and a stylish design. With its combination of performance, convenience, and safety features, it serves as a valuable addition to any modern kitchen.
Top Page Image Contents