Electrolux FMV156DBE service manual Oven Diagram

Page 7

FMV156DBE

FMV156DSE

FMV156DQE

FMV156DCF

Electrical Requirements

The oven is equipped with a 3-prong grounding plug. DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE GROUNDING PIN FROM THE PLUG.

The power supply cord and plug must be connected to a separate 120 Volt AC, 60 Hz, 15 Amp. or more dedicated line, using a grounded receptacle.The receptacle should be located inside the cabinet directly above the Microwave Oven/Hood system mounting location.

3-Pronged Plug

Grounded

Receptacle Box

Grounding Pin

3-Pronged Receptacle

OVEN DIAGRAM

1

6

9

8

3 5

7

2 4

12

9

14

13

1.Oven door with see-through window.

2.Door hinges.

3.Waveguide cover.

4.Turntable motor shaft.

5.Oven lamp.

It will light when oven is operating or door is open.

6.Door latches.

The oven will not operate unless the door is securely closed.

7.Auto Touch control panel

8.Time display: Digital display, 99 minutes 99 seconds.

9.Ventilation openings.

11

10.Light Cover.

11.Grease filters.

12.Removable turntable.

The turntable will rotate clockwise or counterclockwise.

Only remove for cleaning.

13.Removable turntable support.

14. Power supply cord

Image 7

Contents Over the Range Microwave Oven Models Table of ContentsBefore Servicing Dont Touch Before Servicing When the testing is completed Requirements Microwave Measurement Procedure Leakage test Electrolux General Information Product SpecificationOven Diagram Control Panel Description of Operating Sequence OperationHorizontal Venting Vertical VentingRE-CIRCULATION Inside Venting Figure O-1. Oven Schematic-Off Condition Functions Description and Function of ComponentsTroubleshooting Guide CK = Check / RE = Replace Microwave Output Power Procedure Component Test Letter Magnetron Assembly TestPower Transformer Test High Voltage Capacitor Test Magnetron Temperature Fuse TestCavity Thermal CUT-OUT Test Door Sensing Switch Procedure Component Test LetterTEMPERATURE, Replace Temperature Fuse Primary Interlock Switch TestSecondary Interlock Relay RY2 Monitor Switch TestHood Thermal CUT-OUT Test ProcedureHood FAN Motor Test Before testing Relay Test KEY Unit TestLevel Time Foil Pattern on the Printed Wiring Board TestDefrost Center Test 1ST Stage 2ND StageRemoval Occurrence Cause or CorrectionSteps Occurrence Cause or Correction Measuring Point Indication of OHM-METER Procedure Component Test Letter Noise Filter TestDescription of LSI Touch Control Panel AssemblyLSI Signal similar to P46 Signal to sound buzzer 2.0 kHzOUT Oven lamp, fan motor and turntable motor driving signal Signal coming from touch keySegment data signal Key strobe signalHood lamp driving signal Hood motor driving signalServicing of Touch Control Panel Other PrecautionsServicing Shapes of Electronic ComponentsHood Exhaust Louver Removal Component Replacement and Adjustment ProcedureHood FAN Motor Removal Power Transformer RemovalRe-install Pictorial DiagramThermal CUT-OUT Cavity Removal Magnetron RemovalHigh Voltage Rectifier and High Voltage Capacitor Removal Hood FAN Thermal CUT-OUT RemovalCooling FAN Motor Removal InstallationSide View Turntable Motor Positive Lock Connector NO-CASE Type RemovalControl Panel ASSEMBLY, Control Unit and KEY Unit Removal Positive lock connectorControl Unit and KEY Unit Removal Key unit locationDoor Assembly RE-INSTALL Door Replacementdoor Assembly RemovalLatch SPRING, Latch Head and Door Panel Door DisassemblyDoor Frame Assembly Choke CoverPictorial DiagramFigure S-2. Power Unit Circuit LSI Unit Circuit Figure S-4. Printed Wiring Board Control Panel Parts Parts ListElectric Parts Cabinet PartsMiscellaneous Door PartsSCREWS,NUTS, Washers and Other Oven and Cabinet Parts Control Panel Parts Door Parts Miscellaneous Non-replaceable items Packing and AccessoriesFMV156DBE FMV156DSE FMV156DQE FMV156DCF FMV156DBE FMV156DSE FMV156DQE FMV156DCF FMV156DBE FMV156DSE FMV156DQE FMV156DCF