Electrolux FMV156DBE service manual Positive Lock Connector NO-CASE Type Removal, Turntable Motor

Page 33

FMV156DBE

FMV156DSE

FMV156DQE

FMV156DCF

TURNTABLE MOTOR and Food Lamp Sockets REMOVAL

1.Disconnect the power supply cord.

2.Open the door and block it open.

3.To discharge the high voltage capacitor, wait for 60 seconds.

4.Remove the one (1) screw holding the base cover to the oven cavity back plate.

5.Remove the three (3) screws holding the base cover to the oven cavity front face plate.

6.Open the base cover.

7.Release the two hood lamp sockets from the base cover.

8.Remove the base cover from the oven cavity by pulling down and moving to the left slightly.

TURNTABLE MOTOR

9.Disconnect the wire leads from the turntable motor.

10.Remove one (1) screw holding turntable motor to the oven cavity.

11.Now the turntable motor is free.

Hood Lamp Socket

9. Screw the hood lamp off from the lamp socket.

10.Disconnect the wire leads from the lamp socket by pushing the terminal hole of the lamp socket with the small flat type screw driver.

11. Now, the lamp socket is free.

OVEN LAMP and Lamp Socket REMOVAL

1.Disconnect the power supply cord, remove the oven from the wall and remove the outer case. (Refer to procedure of "Removal of Oven from Wall" and "Outer Case removal".). And proceed as follows.

2.Open the door and block it open.

3.To discharge the high voltage capacitor, wait for 60 seconds.

4.Remove the three (3) screws holding the hood intake duct R to the oven cavity top plate, the oven cavity front flange and the fan duct. And remove the hood intake duct R.

5.Turn the lamp socket and release it from the magnetron duct.

6.Screw the oven lamp off from the lamp socket.

7.Now, the oven lamp is free.

8.Pull the wire leads from the oven lamp socket by pushing

the terminal hole of the oven lamp socket with the small flat type screw driver.

9. Now, the oven lamp socket is free.

Oven lamp socket

Terminal

Wire lead

Terminal hole

Flat type small screw driver

POSITIVE LOCK® CONNECTOR (NO-CASE TYPE) REMOVAL

1.Disconnect the power supply cord and remove the oven from wall and remove outer case. (Refer to procedure of "Removal of Oven from Wall" and "Outer case Removal")

2.Open the door and block it open.

3.To discharge the high voltage capacitor, wait for 60 seconds.

4.Push the lever of positive lock® connector.

5.Pull down on the positive lock® connector.

CAUTION: When connecting the positive lock® connectorstotheterminals, install the positive lock® so that the lever

Terminal

Positive lock¨ connector

1

Push

Lever

2 Pull down

faces you.

Positive lock® connector

CONTROL PANEL ASSEMBLY, CONTROL UNIT AND KEY UNIT REMOVAL

1. Disconnect the power supply cord.

2. Open the door and block it open.

3. To discharge the high voltage capacitor, wait for 60 seconds.

4. Remove three (3) screws holding the hood exhaust louver to oven cavity front face plate.

5. Remove the hood exhaust louver from the oven by pushing the right and left tabs of the hood exhaust louver. (Refer to procedure of "HOOD EXHAUST LOUVER REMOVAL")

6. Remove one (1) screw holding the control panel to the oven cavity front face plate.

33

7.Release the control panel from the oven cavity front face plate by lifting it up.

8.Disconnect the wire leads from the relays RY1 and RY2.

9.Disconnect the connectors CN-A, CN-C and CN-E from the control unit.

10.Remove the control panel assembly from the oven.

11.Now, the control panel assembly is free.

12.Disconnect the connector CN-G from the control unit.

13.Remove two (2) screws holding the power unit to the key

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Over the Range Microwave Oven Models Table of ContentsBefore Servicing Dont Touch Before Servicing When the testing is completedMicrowave Measurement Procedure RequirementsLeakage test Electrolux General Information Product SpecificationOven Diagram Control Panel Description of Operating Sequence OperationVertical Venting Horizontal VentingRE-CIRCULATION Inside Venting Figure O-1. Oven Schematic-Off Condition Functions Description and Function of ComponentsTroubleshooting Guide CK = Check / RE = Replace Procedure Component Test Letter Magnetron Assembly Test Microwave Output PowerPower Transformer Test Magnetron Temperature Fuse Test High Voltage Capacitor TestCavity Thermal CUT-OUT Test TEMPERATURE, Replace Temperature Fuse Procedure Component Test LetterPrimary Interlock Switch Test Door Sensing SwitchSecondary Interlock Relay RY2 Monitor Switch TestProcedure Hood Thermal CUT-OUT TestHood FAN Motor Test Before testing Relay Test KEY Unit TestDefrost Center Test Foil Pattern on the Printed Wiring Board Test1ST Stage 2ND Stage Level TimeOccurrence Cause or Correction RemovalSteps Occurrence Cause or Correction Measuring Point Indication of OHM-METER Procedure Component Test Letter Noise Filter TestTouch Control Panel Assembly Description of LSILSI OUT Oven lamp, fan motor and turntable motor driving signal Signal to sound buzzer 2.0 kHzSignal coming from touch key Signal similar to P46Hood lamp driving signal Key strobe signalHood motor driving signal Segment data signalServicing Other PrecautionsShapes of Electronic Components Servicing of Touch Control PanelHood Exhaust Louver Removal Component Replacement and Adjustment ProcedureRe-install Power Transformer RemovalPictorial Diagram Hood FAN Motor RemovalHigh Voltage Rectifier and High Voltage Capacitor Removal Magnetron RemovalHood FAN Thermal CUT-OUT Removal Thermal CUT-OUT Cavity RemovalInstallation Cooling FAN Motor RemovalSide View Control Panel ASSEMBLY, Control Unit and KEY Unit Removal Positive Lock Connector NO-CASE Type RemovalPositive lock connector Turntable MotorControl Unit and KEY Unit Removal Key unit locationDoor Assembly RE-INSTALL Door Replacementdoor Assembly RemovalDoor Frame Assembly Door DisassemblyChoke Cover Latch SPRING, Latch Head and Door PanelPictorial DiagramFigure S-2. Power Unit Circuit LSI Unit Circuit Figure S-4. Printed Wiring Board Electric Parts Parts ListCabinet Parts Control Panel PartsDoor Parts MiscellaneousSCREWS,NUTS, Washers and Other Oven and Cabinet Parts Control Panel Parts Door Parts Miscellaneous Non-replaceable items Packing and AccessoriesFMV156DBE FMV156DSE FMV156DQE FMV156DCF FMV156DBE FMV156DSE FMV156DQE FMV156DCF FMV156DBE FMV156DSE FMV156DQE FMV156DCF

FMV156DBE specifications

The Electrolux FMV156DBE is a modern and versatile microwave oven that combines sleek aesthetics with cutting-edge technology, making it a popular choice for contemporary kitchens. This model offers a range of advanced features designed to streamline cooking and enhance convenience while ensuring users can prepare meals efficiently.

One of the standout features of the Electrolux FMV156DBE is its powerful 1.6 cubic feet capacity, which provides ample space for cooking various dishes, from reheating leftovers to defrosting frozen goods. Its 1,000-watt power output allows for fast and efficient cooking, ensuring that food is heated evenly and thoroughly. The microwave also features multiple power levels, enabling users to customize cooking intensity based on their specific needs.

This model is equipped with the Sensor Cooking technology, which automatically adjusts cooking time and power based on the moisture released from the food. This intelligent feature helps to prevent overcooking or undercooking, delivering perfectly prepared meals every time. Additionally, the FMV156DBE includes a range of pre-programmed cooking settings that cater to different food types, further enhancing usability and efficiency.

Another notable aspect of the Electrolux FMV156DBE is its intuitive touch control panel, allowing for easy navigation through cooking options and settings. The illuminated LED display enhances visibility, making it simple to monitor cooking progress at a glance. The microwave also features a convenient kitchen timer and a clock function, adding to its overall functionality.

The microwave not only excels in cooking performance but also in design. It features a contemporary stainless-steel finish that adds a touch of elegance to any kitchen decor. The streamlined design ensures it can fit seamlessly into various kitchen layouts, while the built-in design options provide flexibility for installation.

Safety is also a priority with the Electrolux FMV156DBE, which includes a child lock feature, preventing unintended use by little hands. This quality makes it an ideal appliance for families with children.

In summary, the Electrolux FMV156DBE is a highly functional microwave oven that features advanced cooking technologies, an ample cooking capacity, and a stylish design. With its combination of performance, convenience, and safety features, it serves as a valuable addition to any modern kitchen.
Top Page Image Contents