Owner’s Manual
Remote Control Setup and Operation
Example of Programming a Macro Sequence:
To program the M1 button in the AUD mode to turn on the Audio receiver, turn on the TV and turn on the VCR.
1.Press AUD and MUTE buttons simultaneously.
The red LED and the AUD button remain lit.
2.Press the M1 button.
3.Press the following buttons:
Press the Power button to select the Audio Power command. Press the TV Device button to select the TV mode.
Press the Power button to select the TV Power command. Press the VCR Device button to select the VCR mode. Press the Power button to select the VCR Power command.
4.Press the CHANNEL UP button.
The red LED and the Device button will blink twice to confirm the program and then turn off.
Note: Each insertion of a Device Button adds a 1/2 second delay to the command sequence. It can take up to 10 seconds to send out 10 commands from a macro button. Please continue to point the remote control at the device(s) until all the commands on the Macro but- ton have been sent out. This will ensure that all the commands are received by the device(s).
Learning Commands from Another Remote
The Model 950’s remote control allows you to transfer a command from a button on your original equipment remote control to a button on the 950’s remote control. New commands can be taught to any button in the DVD, VCR, CD, CBL, AUX, SAT and TV modes except the 8 Source buttons.
The remote control provides distinct visual feedback with the Status LED, located at the top left of the remote control, and with the Source buttons. The LED operates in three colors (red, orange and green). The Device buttons have a red color LED behind them. These LEDs will assist you in programming the learning of the remote control.
Learning a New Command
Select a Source mode in which you would like to teach the new command. For example, if you wanted to learn a new command to the MENU button in the SAT mode on the remote, you would select the SAT Source button and then use the instructions below to teach the new command to the MENU button.
To learn a new command from another remote control:
1.Press a Source button and the SEL/PLAY buttons simultaneously until the orange LED and the Device button turn on and remain lit.
2.On the remote control, press the button that is to be taught the new command.
The orange Status LED will begin to flash continuously. The Device LED will turn off.
3.On the source remote control (original remote control), press and hold the button for the command to be learned until the Status LED on the remote turns green. Release the button on the source remote control.
Both remote controls must be next to each other with the IR emitters face to face.
4.Press the button on the source remote control, once again to verify that the new command has been learned correctly. The Status LED will flash green twice and then turn to a steady orange color indicating that the programming was successful. The Source button will light.
Repeat Steps 2 through 4 for any other buttons to be taught in the Device mode selected in Step 1. Once you have completed learning new com- mands to buttons in the selected Source mode, proceed to Step 5.
5.To save the learned commands, press and hold the Source and SEL/PLAY buttons simultaneously until the orange Status LED flashes twice.
The Source button light will turn off.
Please repeat for any other Source modes starting from Step 1.
To erase a learned command from a button:
1.Press the Source button and SEL buttons simultaneously until the orange Status LED and the Device button turn on and remain lit.
2.On the remote control, press the button that is to be erased.
The orange Status LED will flash continuously and the Device button will turn off.
3.Press the Light button.
The green status LED will flash twice, then turn to a steady orange. The Device button will turn on.
Repeat from Step 2 for any other buttons to be erased in the selected Source mode.
4.To exit, press and hold the Source button and the SEL/PLAY button simultaneously once again. The orange Status LED will flash twice and then turn off. The Device button will turn off.
To erase all the learned commands in one device mode:
1.Press the Source button and SEL buttons simultaneously until the orange Status LED and the Device button turn on and remain lit.
2.Press the LIGHT button until the red Status LED flashes five times and then flash green twice.
The Device button will turn off. The Status LED will go to a constant orange indicating that all the learned information on buttons in the Device mode have been erased. The Device button will turn on.
3.To exit, press and hold the Source button and the SEL/PLAY button simultaneously once again. The orange Status LED will flash twice and then turn off. The Device button will turn off.
To erase all the learned commands in all device modes:
Note: This procedure will erase all learned commands on all buttons in the CD, TV, DVD, SAT, CBL, VCR and AUX Source modes.
Press and hold the TV Source button and the LIGHT button simultaneously.
The red Status LED will flash continuously. The Status LED will then flash green once, orange once then turn off, indicating that all of the learned commands on all of the device modes on the remote control have been erased.
