Electrolux 50740 manual Connecting the Dishwasher, Water Connection, Permitted water pressure

Page 36

Installation and Connection Instructions

Connecting the Dishwasher

Water Connection

The dishwasher is fitted with safety devices that prevent the wash water returning into the drinking water system and comply with the applicable plumbing regulations.

The dishwasher must be connected to a cold water supply.

The dishwasher must not be connected to open hot water appliances or instantaneous water heaters.

Permitted water pressure

Lowest permitted water pressure:

Consult your installer if the water pres-

1 bar (=10 N/cm2 =100 kPa)

sure is less than 1 bar.

Highest permitted water pressure:

In the case of a water pressure greater

10 bar (=100 N/cm2 =1 MPa)

than 10 bar, a pressure reduction valve

 

must be used (available from your

 

dealer).

 

 

 

Connect the inlet hose

1

The water inlet hose must not be kinked, crushed or entangled when it

 

is being connected up.

0Connect the threaded hose fitting (ISO 228-1:2000) on the water inlet hose to a tap with an external thread (¾ inch). Tighten the threaded hose fitting hand tight only.

3

• In order that access to the tap in the kitchen is not limited by the use

 

of the dishwasher, we recommend the installation of an additional

tap, or fitting a two way adapter to the existing tap.

• If you need a longer water inlet hose than that supplied, VDE approved complete hose sets are to be used. These are available from your local Service Force Centre.

• Do not use, for connection, old hoses which have been used for another appliance.

36

Image 36
Contents Favorit Tips on using the appliance Dear customerPlease read these user instructions carefully Pass them on to any subsequent owner of the applianceContents Installation and Connection Instructions Safety Instructions Installation, Connection and Placing into OperationChild Safety General SafetyCorrect Use Disposal Economical and Ecological DishwashingDisposing of the Packaging Material Disposal of Old AppliancesAppliance Features and Control Panel Control panel NingPrior to using for the first time Adjust the water softenerYour area PanelDishwasher must be switched off Manual settingElectronic setting Ing the appropriate buttonFilling with Salt for the Water Softener Fill with dishwasher saltRemain illuminated Open the door, remove the lower Basket Turning it anticlockwiseTo switch off the control indicator for rinse aid Rinse aidRinse aid can be added in one of two ways Filling with rinse aid Fully open the rinse aid compartment lidAdjusting Rinse Aid Dosing Daily UseLoading Cutlery and Dishes Not be washed in the dishwasherLoading Cutlery Loading Pans, Frying Pans Large Plates Folded over to the leftTo ease the loading of large items Two right-hand plate insertsFolded across one another Across one anotherTwo rear plate inserts in the lower Baskets can be folded across one anotherLoading Cups, Glasses and Coffee Services Adjusting the Height of the Upper Basket Lowering the Upper BasketRaising the Upper Basket Filling with Detergent Fill with detergentGeneral Advice Special AdviceUse of 3 in 1/ Combi Detergent Tablets Concentrated Detergent Detergent tabletsSelecting the Wash Programme Programme Table AdditionStart the wash programme Interrupting or ending the wash programmeWasher Open the door carefullySetting or changing the delay start timer Setting the delay start timerChanging the delay start timer Pause functionCare and Cleaning Switching Off the DishwasherSive cleaners Emptying the DishwasherCleaning the Filter StancesFault warnings are displayed What to do, ifThere are problems with the operation of the dish- washer Wash results are not satisfactoryDishes are still dirty Dishes are wet and dullTechnical Data Lower rinse aid dosingThere are dried water drops on the glasses and dishes Sample loading arrangements Upper basket Lower basket with cutlery basketInstalling the Dishwasher See enclosed installation instructionsBuilt-Under Dishwasher Free-Standing AppliancesPlinth on free-standing appliances is not adjustable Work surface must be re-mountedConnecting the Dishwasher Water ConnectionPermitted water pressure Connect the inlet hoseWater inlet hose with safety valve Please take care when installing the water inlet hoseWater drain Leak Prevention System Appliance is automatically pumped outElectrical Connection Changing a fuseConnections Guarantee Conditions 08705 929 Customer CareCalls may be recorded for training purposes AEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG