Electrolux CSIG 511 Connecting to GAS, Connection to the Electricity Supply

Page 47

4. CONNECTING TO GAS

This appliance is designed to be installed with an appliance flexible connection only. Supply piping should not be less that R³/8. Connection is made to the Rc ½ (½" B.S.P.) female threaded entry pipe located just below the hotplate level on the rear left hand side of the appliance. NOTE:

ONLY LIQUID SEALANTS TO BE USED WHEN INLET GAS PIPE IS FITTED TO SHUT OFF VALVE I.E.: DO NOT USE P.T.F.E. SEALANT TAPE. Check for gas soundness after connecting to the gas supply.

The gas bayonet connector must be fitted in the shaded area indicated in Fig.3. Take into account that it must be possible to pull the appliance forward sufficiently. The hose must not get caught on the stability bracket.

IMPORTANT: FLEXIBLE TUBING USED MUST COMPLY WITH BS. 669 CURRENT EDITION.

L.P.G. FLEXIBLE CONNECTIONS MUST BE OF A TYPE SUITABLE FOR L.P.G. AND CAPABLE OF OPERATION UP TO 50 mbar AND TO CARRY A RED STRIPE, BAND OR LABEL.

50 100

Fig.3

850 700

250

450

All dimensions in

mm

5. CONNECTION TO THE ELECTRICITY SUPPLY

WARNING: THIS APPLIANCE MUST BE EARTHED. DO NOT EARTH THIS APPLIANCE TO THE GAS SUPPLY PIPING.

This appliance must be connected to 230V-240V A.C. 50Hz supply. It is supplied with 2 metres of 5 amp 3 core cable incorporating a moulded 13 amp plug , fitted with a 3 amp fuse, which can be plugged directly into the nearest suitable socket. Ensure the plug is accessible to the user. If this is not long enough, the supply cable can be replaced totally by a longer cable at least 0.75mm² nominal cross sectional area (24/0.2mm).

IF THE MOULDED PLUG IS CUT FROM THE CABLE

 

FOR ANY REASON, IT MUST BE DESTROYED OR

 

DISPOSED OF SAFELY, AS THE PROTRUDING

 

WIRES WILL BE AN ELECTRIC SHOCK HAZARD.

Fig.4

If any other type of plug is used it should incorporate a 3

amp fuse in either the plug or adapter or at the distribution

 

board.

 

If the cable has to be threaded through small apertures in cabinets etc., it may be disconnected from the appliance, then re-connected to as shown in Fig.4.

DO NOT EXTEND THE CABLE USING PLASTIC OR CERAMIC CONNECTION TERMINAL BLOCKS AND/OR INSULATION TAPE.

ALL EXTERNAL WIRING BETWEEN THE APPLIANCE AND THE ELECTRICAL SUPPLY SHALL COMPLY WITH I.E.E. WIRING REGULATIONS.

47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Csig Introduction For your safetyContents Hotplate Lighting the applianceSecond oven Leave the grill door open when you are using the grillGrill/second oven GrillOven light Main ovenTo turn off any burner Heat control Prior to using the grillHigh setting GrillPositioning food onthe grid Cooking positionsGeneral PreheatingGrill pan is supplied with a removable handle Grill pan and handleBurner sizes HotplateFor your safety Helpful hints Oven shelves OvensHeat zones Most second oven cooking should be Baking trays and dishesCondensation RoastingOven cooking chart Main oven 205 mm ½ 2¾ hours Mins. per ½kg 1lb and 25 minsMins. per ½kg 1lb and 15 mins ¼ 2¾ hoursRolls and buns 10 20 mins 30 40 minsBase Well Done Oven cooking chart Second ovenBase Medium Lamb Shelf on Medium½ hours Individual 20 30 mins Cakes Christmas Cake Shelf ½ 4½ hoursBaked custard 50 60 mins Pastries Plate tart shortcrust 25 35 minsFruit pie shortcrust 25 35 mins Baking trayTo use the Countdown Electronic timerTurn the selector knob to Manual then turn to Time Setting To set the time of dayAutomatic control Setting the controls for automatic useWill go out How long will Turn the selector knob to Food takeTo cook? Cooked by?Hints and tips for automatic cooking Please note There is no slow cook on the second oven Slow cookingFood preparation slow cooking Thaw thoroughly before cooking Do not cook casseroles over 2.7kg 6lbCover food with a tight fitting lid or tin foil Cleaning the brass plated handle Where applicable Care and cleaning For your safetyCrown to body Do not try to force the crown on to the body When replacing hotplate burner partsGrill and top oven Main oven Main oven cleaning cycle To remove the outer glass Cleaning between the outer and inner door glassFor further details see Cleaning The Door GlassInstalling the appliance LocationHeight to hotplate 900mm 920mm Appliance dimensionsPositioning Curtains behind the applianceMoving your appliance General information For your safetyConnecting to the electricity supply Replacing the oven light bulb Check What is wrong and why?Probably a fault 7 0 5 9 2 9 9 2 Service and spare partsCustomer Care Department Installation Instructions Hotplate DimensionsConnections GrillGeneral Important Safety RequirementsMain Oven Second OvenLocation of Appliance Fitting the Stability Bracket Parts RequiredLevelling the Appliance Connection to the Electricity Supply Connecting to GASChecking LID SHUT-OFF Device Pressure TestingChecking the Grill Checking the HotplateAutomatic Operation Checking the Main Oven ControlsChecking the Main Oven General Note CSIG511Checking the Second Oven Checking the Main Oven LightContents Check List Telephone 0870 5 Part Number311590704 55 77 High Street

CSIG 511 specifications

The Electrolux CSIG 511 is a modern, sleek steam generator iron designed to make the task of ironing more efficient and comfortable. This appliance combines powerful steam technology with user-friendly features, ensuring that every crease is smoothed out with ease.

One of the standout features of the CSIG 511 is its impressive steam output. With a continuous steam production of up to 130 g/min, it delivers a strong burst of steam that penetrates fabrics deep, making it particularly effective for tackling stubborn wrinkles on various materials, including cotton and linen. This high steam output is complemented by a steam boost function, which can generate an even more concentrated burst of steam at 480 g, ideal for vertical steaming of hanging garments or delicate fabrics.

The CSIG 511 also boasts a large water tank capacity of 1.5 liters, allowing for extended ironing sessions without the need for frequent refills. The tank is detachable, making it convenient to fill up under the tap. Additionally, the appliance features a built-in anti-calc system that helps combat limescale buildup, ensuring longevity and performance over time.

User comfort is a priority in the design of the Electrolux CSIG 511. It features an ergonomic handle that is comfortable to grip for prolonged use, and the iron itself is lightweight, reducing fatigue during lengthy ironing tasks. The 2.5-meter power cord provides flexibility and ease of movement, allowing users to freely navigate around the ironing area.

Another noteworthy characteristic is the advanced soleplate technology of the CSIG 511. The soleplate is designed with a durable non-stick coating that glides smoothly over fabrics, preventing snagging while enhancing heat distribution for optimal results. The pointed tip of the soleplate aids in reaching difficult areas such as collars and seams with precision.

Safety features have also been thoughtfully incorporated into the CSIG 511. It includes an automatic shut-off function that activates when the appliance is left unattended for a designated period, reducing fire risks and providing peace of mind.

In summary, the Electrolux CSIG 511 steam generator iron is a powerful and efficient appliance that combines cutting-edge technology with user-friendly design. With high steam output, a large water tank, ergonomic features, and safety mechanisms, it transforms ironing into a quick and hassle-free experience for users.
Top Page Image Contents