LEG Leveler Installation, Final Preparation | Viking F20497 specification

LEG LEVELER INSTALLATION

Read Before Installing Leg Levelers

WARNING: Do not lay unit on top, side, back, or front. If unit is accidentally laid in any position other than right side up, then the unit must remain in the right side up position for at least 24 hours before plugging the unit in.

1.	Tip unit backwards so there is one foot of clearance on front of the unit. Have someone to assist you in tilting the
	unit to prevent it from falling on you while installing the leg levelers.
2.	Screw front two (2) leg levelers into the weldnuts (24” W. Models) or screw impressions (15” W. Models). Leg
	levelers should be screwed in until snug.
3.	Repeat steps 1 & 2 with the exception of tipping the unit forwards to screw in the back two leg levelers.
4.	The leg levelers are now installed.
5.	The unit should be level from front to back and side to side. If floor conditions do not allow the unit to sit level,
	adjust the leg leveler by turning the required leg leveler counter-clockwise to increase the height and clockwise to
	reduce the height.

FINAL PREPARATION

1.Some stainless steel parts may have a plastic protective wrap which must be peeled off. The interior of the refrigerated beverage center should be washed thoroughly with hot, soapy water, rinsed and wiped dry to remove film residue and any installation dust or debris before being used. Solutions stronger than soap and water are rarely needed.

2.All stainless steel parts should be wiped with hot soapy water. If buildup occurs, do not use steel wool, abrasive cloths, cleaners, or powders. If it is necessary to scrape stainless steel to remove encrusted materials, soak with hot, wet cloths to loosen the material, then use a wood or nylon scraper. Do not use a metal knife, spatula, or any other metal tool to scrape stainless steel; scratches are almost impossible to remove.

LIGHT ASSEMBLY REPLACEMENT - 15” W. Models

WARNING	ELECTRICAL SHOCK HAZARD
WARNING	Failure to follow these instructions could result in fire or electrical shock.

ELECTRICAL CONNECTION

WARNING	ELECTRICAL SHOCK HAZARD
WARNING	Failure to follow these instructions could result in fire or electrical shock.

NOTE: Please co ntact y our Vi king R ange Corporation parts distributor or dealer to o rder new light assembly.

To replace the light, first disconnect the refrigerated beverage center’s power cord. Next,

Green		Light
ground wire		assembly

Hex head screw

Electrical Requirements

A 115 volt, 60 Hz, AC on ly 15 am p fused electr ical supply is required. (A time delay fuse or circuit breaker is recommended.) It is recommended that a separate circuit, serving only this appliance, be provided.

•ELECTRICAL GROUND IS REQUIRED ON THIS APPLIANCE. •DO NOT UNDER ANY CIRCUMSTANCES REMOVE THE POWER SUPPLY CORD GROUND PLUG.

•DO NOT USE AN EXTENSION CORD

		Grounding type wall
	Power Supply with	Grounding type wall
	Power Supply with	receptacle
	3-prong grounding	receptacle
	3-prong grounding
	plug

remove both the green ground wire screw located on the left of the light assem bly and the other screw located o n the right of the light assembly with a 5-16” hex head screwdriver. (See drawing). Unplug the light unit and r emove complete light assembly.

To install the new light assem bly, screw in the green ground wire screw and the screw located on the right with a 5/16” hex head screwdriver and plug the light unit in.

	Hex head
Plug	screw
Plug

Recommended Grounding Methods

For your personal safety, this refrigerated beverage center must be grounded. This appliance is equipped with a 7’ (2.1

m)power supply cord having a 3-prong grounding plug. To minimize possible shock hazard, the cord must be plugged into a mating 3-prong grounding type wall receptacle grounded in accordance with the National Electrical Code and local codes and ordinances. If the circuit does not have a grounding type receptacle, it is the responsibility and obligation of the customer to e xchange the existing receptacle in accordance with the National Electrical Code and applicable local codes and ordinances. The third ground plug SHOULD NOT, under any circumstances, be cut or removed. All UL listed refrigerated beverage centers are equipped with this type of plug.

LIGHT BULB REPLACEMENT - 24” W. Models

WARNING	ELECTRICAL SHOCK HAZARD
WARNING	Failure to follow these instructions could result in fire or electrical shock.

This unit uses a 15-watt incandescent bulb located behind the display housing.

To replace the light bulb:

1.Unscrew the old light bulb located behind the display housing.

2.Discard the old light bulb.

3.Screw new light bulb into location behind the display housing.

ENERGY SAVING TIPS

•Reduce door openings.

•Close the door as soon as you can.

•Keep the condenser coils on bottom of the refrigerated beverage center clean. (See “Cleaning and Maintenance”.) •Adjust the temperature control to a warmer setting when practical.

•Do not put hot foods in the refrigerated beverage center. •Install unit away from the stove or other heat sources.

F20497 specifications

The Viking F20497 is a notable addition to the lineup of utility vehicles that prioritize performance, reliability, and versatility. Designed primarily for agricultural and off-road applications, the F20497 showcases a robust framework that stands out in its class.

One of the most commendable features of the Viking F20497 is its powerful engine. Equipped with a 4-stroke, liquid-cooled engine, it delivers impressive horsepower, allowing the vehicle to navigate through challenging terrains effortlessly. The engine is designed for optimal fuel efficiency, ensuring that operators can work longer hours without the frequent need for refueling.

The drivetrain is complemented by a seamless automatic transmission, enhancing the ease of use for operators. This transmission is engineered to deliver smooth gear shifts and provides the flexibility required for various applications, from hauling and towing to navigating steep inclines. The four-wheel drive (4WD) system further aids traction, making the F20497 a reliable companion for both work and recreational use.

In terms of size and dimensions, the F20497 is compact enough to maneuver in tight spaces while still providing ample cargo capacity. Its generous payload capacity makes it an excellent choice for transporting materials, tools, and equipment across fields or construction sites.

The Viking F20497 is designed with comfort and safety in mind. The spacious cab offers ample legroom and is equipped with ergonomic seating, ensuring that operators remain comfortable even during extended use. Additionally, the vehicle features a rugged design with reinforced chassis and body panels, making it capable of enduring rough handling.

Technologically, the F20497 stands out with its integrated digital display, which provides essential information at a glance. This feature enhances operational efficiency by allowing drivers to monitor speed, engine performance, and fuel levels easily.

Furthermore, the Viking F20497 is designed with environmental considerations in mind, as the engine adheres to the latest emission standards, making it a more eco-friendly choice for operators seeking to reduce their carbon footprint.

Overall, the Viking F20497 is a formidable utility vehicle that combines power, efficiency, and comfort, making it an ideal option for those in need of a reliable workhorse in demanding environments. Whether used for agricultural tasks, outdoor adventures, or job site operations, the features and capabilities of the F20497 ensure it remains a top contender in its category.