KitchenAid manual Installation Instructions, UnpackRefrigerator, Reduce TippingRadius

Page 18

INSTALLATION INSTRUCTIONS

UnpackRefrigerator

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure do so can result in death or serious injury.

IMPORTANT:

Do not remove the protective film or cardboard from door or grille until the refrigerator is in its operating position.

All 4 leveling legs must contact the floor to support and stabilize the full weight of the refrigerator.

Keep the cardboard shipping piece or plywood under the refrigerator until it is installed in the operating position.

1.Remove the 4 brackets (2 on each side) that attach the shipping base to the refrigerator bottom.

NOTE: Do not remove tape and door bracing until the refrigerator is in its final position.

2.Place an appliance dolly under the freezer side of the refrigerator. Be sure to protect the side trims and handles. Place the corner posts from the packing materials over the trims and handles as appropriate. Carefully tighten the strap.

NOTE: Pass the dolly strap under the handles for the Architect® Series.

Reduce TippingRadius

(if required)

Before bringing the refrigerator into the home, be sure there is adequate ceiling height to stand the refrigerator upright. See “Tipping Radius” in the “Installation Requirements and Design Specifications” section for more information.

If you do not have adequate ceiling height to stand the refrigerator upright, the tipping radius can be reduced by removing the top grille and side trims (see the following chart).

Model Reduced Tipping Radius

3688" (223.5 cm)

4288¹⁄₂" (224.8 cm)

4889¹⁄₄" (226.7 cm)

Classic and Overlay Series

1.Grasp both ends of the top grille.

2.Push the top grille straight up, then pull straight out. Lay the grille on a soft surface.

BAB

A. Top grille

B. Cabinet side trim

3.Remove the 6 screws attaching each cabinet side trim to the refrigerator and remove the side trims.

4.Stand the refrigerator up. First, place the left bottom edge of the refrigerator on the floor, stand the refrigerator upright and then lower the right-hand side of the refrigerator to the floor.

5.Reassemble the trim and top grille after the dolly has been removed from the refrigerator.

Architect® Series

1.Grasp both ends of the louver panel. Push the louver panel straight up, then pull straight out. Lay the panel on a soft surface.

2.Grasp both ends of the top grille. Push the top grille straight up, then pull straight out. Lay the top grille on a soft surface.

BAB

3.Place pieces of the shipping carton on the floor when rolling the dolly and refrigerator into the house. Move the refrigerator close to the built-in opening.

C

A. Top grille

B. Cabinet side trim C. Louver panel

18

Image 18
Contents Table of Contents/Índice/Table des matières Side by Side BUILT-IN RefrigeratorTable of Contents ÍndiceTable DES Matières Refrigerator Safety Your safety and the safety of others are very importantArchitect Series Design SpecificationsModels Side by Side Non-Dispensing Refrigerators Overlay SeriesModels Side by Side Dispensing Refrigerators Classic SeriesComplete Series Front View Product DimensionsSide View Top ViewForward Tipping Radius DoorSwing DimensionsTipping Radius ModelsHandleandDoorClearances Overlay Series Door Classic SeriesFactory Panelsand Kits Classic SeriesCustom PanelsDoor Panels Routing Requirements Door Panels for Dispenser ModelsTop Grille Panel Routing Requirements Standard Handle Top View40¹⁄₂ 102.87 cm OverlaySeries CustomPanels34¹⁄₂ 87.63 cm 46¹⁄₂ 118.11 cmClassic, Architect and Pro Line Series Custom Side Panels OverlaySeries Custom Side PanelsRefrigerator Side Trim Installation RequirementsTools and Parts Measure the distance from point a as shown to back wallLocation Requirements Opening DimensionsSwing Dimensions Location should permit doors to open fully. See DoorRecommended Grounding Method Electrical RequirementsWater Supply Requirements Cold Water SupplyReduce TippingRadius Installation InstructionsUnpackRefrigerator Classic and Overlay SeriesStyle 1 Connecting to a Water Valve Install Anti-Tip BoardsTo Install Anti-tip Boards Connect Water SupplyPlug in Refrigerator Install ClassicSeries CustomPanelsLowerLevelingLegs Move Refrigerator toFinal PositionInstall OverlaySeries Custom Panels Door Panel InstallationReinstall the handle-side and top trims Level Refrigerator Adjustand Remove Doors Install Side Panel Install Base GrilleComplete Installation Seguridad DEL Refrigerador Su seguridad y la seguridad de los demás es muy importanteEspecificaciones DE Diseño Modelos Refrigeradores de dos puertas sin despachadorModelos Refrigeradores de dos puertas con despachador Serie CompletaVista superior Medidasdel productoVista lateral Vista frontalArco de vuelco hacia adelante Modelos de Arco devuelcoMedidas de oscilación de las puertas Arco de vuelco lateralEspaciospara la agarradera y la puerta Serie Overlay Soporte Panelesy juegosde fábrica delaSerie Classic Panelesde la puerta a la medida para la Serie ClassicRequisitos de contorneado de los paneles de la puerta Paneles de puerta para modelos con despachadorRequisitos de contorneado del panel de la rejilla SuperiorPaneles a la medida de la Serie Overlay Paneles decorativos Overlay ModeloPaneles de soporte Modelo Paneles laterales a la medida para la Serie Overlay Requisitos DE Instalación Piezas y HerramientasRequisitosde ubicación Medidas de la aberturaRequisitoseléctricos Método de conexión a tierra recomendadoSuministro de agua fría Cómoreducirelarco de vuelco Instrucciones DE InstalaciónCómo desempacarsurefrigerador Series Classic y OverlaySerie Pro Line Cómo instalarlos tablerosantivuelcoCómoconectar el suministro de agua Cómo instalar los tableros antivuelcoEstilo 1 Conexión a una válvula de agua Cómo enchufarel refrigeradorUbicación final delrefrigerador Estilo 2 Conexión a una tubería de aguaPaneles de la puerta Baje las patas niveladorasCómo instalarlos panelesa la medida para la Serie Classic Pulg lb cm kgCómo instalarlos panelesa la medida para la Serie Overlay Instalación del panel de la puertaCómo quitar la puerta Cómonivelar el refrigeradorAjuste y quite las puertas Siga los siguientes pasos para volver a instalar la puertaModelos Overlay Cómoinstalarel panellateralCómo ajustar la oscilación de las puertas Quite la placa de traba, como se muestraCómo instalarla rejilla de la base Cómoterminarla instalaciónSécurité DU Réfrigérateur Votre sécurité et celle des autres est très importanteSérie Architect Spécifications DE DesignModèles Réfrigérateurs côte à côte sans distributeur Série Overlay Série ClassicModèles Réfrigérateurs côte à côte avec distributeur Série OverlaySérie Complète Vue avant Dimensionsdu produitVue latérale Vue de dessusModèles de Dimensionspourle pivotement des portesRayon debasculement Rayon de basculement avantDégagementspourlespoignées et portes Série Overlay Panneau Ensembles de panneaux dorigine de la série Classic Panneaux personnalisés de la Série ClassicExigences dusinage des panneaux de porte Panneaux de porte pour modèles avec distributeurExigences dusinage du panneau de la grille supérieure Poignée standard Vue supérieurePanneaux personnalisés de la série Overlay Panneaux de soutien ModèlePanneaux latéraux personnalisés de la Série Overlay Exigences ’INSTALLATION Outillage etpiècesnécessairesSupérieure. Voir Dimensions de l’ouverture Exigences d’emplacementDimensions de l’ouverture Modèle Largeur a tel quillustré ci-dessusSpécifications de l’alimentation en eau Méthode recommandée de mise à la terreSpécifications électriques Arrivée d’eau froideRéduction du rayon de basculement Instructions D’INSTALLATIONDéballage du réfrigérateur Séries Classic et OverlaySérie Architect Installation de planchesantibasculementInstallation des planches antibasculement Série Pro LineBrancherle réfrigérateur Déplacementdu réfrigérateurà Lemplacement finalRaccordementde la canalisation d’eau Style 1 Raccordement à la canalisation deauInstallation des panneaux personnalisés de la Série Classic Déploiement despiedsde nivellementPanneaux de porte Installation despanneaux personnalisés de la Série Overlay Installation des panneaux de porteTringle supérieure Ajustementetenlèvement desportes Suivre les étapes suivantes pour réinstaller la porteNivellementdu réfrigérateur Enlèvement des portesInstallation du panneau latéral Ajustement de l’ouverture des portesModèles Overlay Installation de la grille de la base Acheverl’installation2266811A All rights reserved
Related manuals
Manual 23 pages 20.17 Kb

Refrigerator specifications

The KitchenAid 338 Refrigerator, model 4KSRF42D, is an exemplary appliance that combines functionality with a sleek design, making it a prime choice for modern kitchens. This refrigerator offers an impressive blend of features, technologies, and characteristics that elevate food storage and preservation.

One of the standout features of the 4KSRF42D is its spacious interior. With a total capacity that accommodates a significant amount of groceries, this refrigerator ensures that there is ample room for all your food items and beverages. Configured with adjustable shelves and spacious bins, organization and access to your favorite foods are simple and efficient.

The refrigerator incorporates the innovative Preserva Food Care System. This advanced technology utilizes dual cooling systems that maintain optimal humidity levels and temperature, helping to keep fruits and vegetables fresher for longer periods. The system cleverly prevents the transfer of odors between the refrigerator and freezer, ensuring that your food maintains its intended flavor.

Another notable characteristic of the KitchenAid 338 is its sleek stainless-steel exterior, which not only looks modern but is also easy to clean. The fingerprint-resistant finish helps keep the appliance looking immaculate, even in bustling kitchen environments. Additionally, the countertop depth design means it seamlessly integrates into kitchen cabinetry for a built-in look.

Energy efficiency is a key consideration for modern consumers, and the 4KSRF42D excels in this regard as it meets Energy Star certification standards. This ensures minimal energy consumption without compromising on performance, ultimately reducing your utility bills while being environmentally friendly.

The refrigerator is equipped with a sophisticated ice maker located in the freezer compartment. This feature means you always have a reliable supply of ice at hand for those hot summer days or entertaining guests. The easy-to-access water dispenser on the exterior front allows for instant hydration with filtered water.

In terms of digital technology, the KitchenAid 338 comes with an intuitive LCD display that allows users to easily monitor and adjust temperature settings in both compartments. Smart functionality ensures that users can even receive alerts to changes in temperature through mobile notifications, offering added convenience.

Overall, the KitchenAid 338 Refrigerator, model 4KSRF42D, is a culmination of advanced features and elegant design. Its emphasis on preserving food quality, energy efficiency, and user-friendly technology makes it an excellent addition to any contemporary kitchen. Whether you are an avid home chef or simply looking to upgrade your kitchen appliances, this refrigerator constitutes a worthy investment that promises reliability and aesthetic appeal.