KitchenAid Refrigerator manual Adjustand Remove Doors

Page 23

Adjustand Remove Doors

Door Removal

NOTE: Do not remove the two ¹⁄₄" hex-head mounting screws.

A

B

A.T27 flat-head mounting screws

B.¹⁄₄" hex-head mounting screws

Use the following steps to remove doors during installation.

1.Loosen and remove the 4 T27 flat-head mounting screws on top of both hinges. Keep the screws together.

2.Lift the doors up and away from the refrigerator and set them aside.

Use the following steps to reinstall the door.

1.Position the doors so the mounting screw holes on top of both hinges are aligned.

2.Insert the 4 T27 flat-head mounting screws on top of both hinges. Make sure the spacing between the doors is the same distance at the top and bottom.

3.Tighten the screws on the hinge.

Door Height Adjustment

Use the following steps to adjust the door height, up or down, after the doors have been leveled.

1.Open the freezer or refrigerator door. Locate the bottom hinge and remove the door stop screw.

Classic and Architect® Models

Remove the door stop screw from the bottom side of the hinge.

AB C

A.Bushing

B.Door stop screw

C.Locking plate

Overlay Models

Remove the 2 door stop screws: one from the bottom side using a ³⁄₈" open end wrench and one from the top side using an Allen wrench.

AB

A.Door stop screw from bottom

B.Door stop screw from top (110°)

2.Remove the locking plate as shown.

3.Turn the bushing located underneath the bottom of the hinge using the open-end wrench. Turning the bushing to the left (counterclockwise) will raise the door. Turning the bushing right (clockwise) will lower the door.

4.After adjusting, check the doors to make sure they are even at the top and bottom. If the doors are not even, continue to turn the bushing to adjust the door height.

5.Replace the locking plate.

6.Turn the bushing slightly to align the hinge and locking plate screw holes.

7.Replace the door stop screw or screws and tighten.

IMPORTANT: Do not place the door stop screw in the 130° position on Overlay Series models. See “Handle and Door Clearances.”

8.Make final recheck to make sure the doors are aligned and even.

Door Swing Adjustment

1.Check that the refrigerator door can open freely. If the door opens too wide, remove the door stop screw or screws (depending on your model) from the bottom hinge. See “Door Height Adjustment” earlier in this section.

2.Hold the door open to a position that is less than 90°.

23

Image 23
Contents Side by Side BUILT-IN Refrigerator Table of Contents/Índice/Table des matièresTable DES Matières Table of ContentsÍndice Your safety and the safety of others are very important Refrigerator SafetyOverlay Series Design SpecificationsModels Side by Side Non-Dispensing Refrigerators Architect SeriesComplete Series Models Side by Side Dispensing RefrigeratorsClassic Series Top View Product DimensionsSide View Front ViewModels DoorSwing DimensionsTipping Radius Forward Tipping RadiusHandleandDoorClearances Overlay Series Door Classic SeriesCustom Panels Classic SeriesFactory Panelsand KitsStandard Handle Top View Door Panels for Dispenser ModelsTop Grille Panel Routing Requirements Door Panels Routing Requirements46¹⁄₂ 118.11 cm OverlaySeries CustomPanels34¹⁄₂ 87.63 cm 40¹⁄₂ 102.87 cmOverlaySeries Custom Side Panels Classic, Architect and Pro Line Series Custom Side PanelsMeasure the distance from point a as shown to back wall Installation RequirementsTools and Parts Refrigerator Side TrimLocation should permit doors to open fully. See Door Opening DimensionsSwing Dimensions Location RequirementsCold Water Supply Electrical RequirementsWater Supply Requirements Recommended Grounding MethodClassic and Overlay Series Installation InstructionsUnpackRefrigerator Reduce TippingRadiusConnect Water Supply Install Anti-Tip BoardsTo Install Anti-tip Boards Style 1 Connecting to a Water ValveMove Refrigerator toFinal Position Install ClassicSeries CustomPanelsLowerLevelingLegs Plug in RefrigeratorReinstall the handle-side and top trims Install OverlaySeries Custom PanelsDoor Panel Installation Level Refrigerator Adjustand Remove Doors Complete Installation Install Side PanelInstall Base Grille Su seguridad y la seguridad de los demás es muy importante Seguridad DEL RefrigeradorModelos Refrigeradores de dos puertas sin despachador Especificaciones DE DiseñoSerie Completa Modelos Refrigeradores de dos puertas con despachadorVista frontal Medidasdel productoVista lateral Vista superiorArco de vuelco lateral Arco devuelcoMedidas de oscilación de las puertas Arco de vuelco hacia adelante Modelos deEspaciospara la agarradera y la puerta Serie Overlay Soporte Panelesde la puerta a la medida para la Serie Classic Panelesy juegosde fábrica delaSerie ClassicSuperior Paneles de puerta para modelos con despachadorRequisitos de contorneado del panel de la rejilla Requisitos de contorneado de los paneles de la puertaPaneles de soporte Modelo Paneles a la medida de la Serie OverlayPaneles decorativos Overlay Modelo Paneles laterales a la medida para la Serie Overlay Piezas y Herramientas Requisitos DE InstalaciónMedidas de la abertura Requisitosde ubicaciónSuministro de agua fría RequisitoseléctricosMétodo de conexión a tierra recomendado Series Classic y Overlay Instrucciones DE InstalaciónCómo desempacarsurefrigerador Cómoreducirelarco de vuelcoCómo instalar los tableros antivuelco Cómo instalarlos tablerosantivuelcoCómoconectar el suministro de agua Serie Pro LineEstilo 2 Conexión a una tubería de agua Cómo enchufarel refrigeradorUbicación final delrefrigerador Estilo 1 Conexión a una válvula de aguaPulg lb cm kg Baje las patas niveladorasCómo instalarlos panelesa la medida para la Serie Classic Paneles de la puertaInstalación del panel de la puerta Cómo instalarlos panelesa la medida para la Serie OverlaySiga los siguientes pasos para volver a instalar la puerta Cómonivelar el refrigeradorAjuste y quite las puertas Cómo quitar la puertaQuite la placa de traba, como se muestra Cómoinstalarel panellateralCómo ajustar la oscilación de las puertas Modelos OverlayCómoterminarla instalación Cómo instalarla rejilla de la baseVotre sécurité et celle des autres est très importante Sécurité DU RéfrigérateurSérie Overlay Série Classic Spécifications DE DesignModèles Réfrigérateurs côte à côte sans distributeur Série ArchitectSérie Complète Modèles Réfrigérateurs côte à côte avec distributeurSérie Overlay Vue de dessus Dimensionsdu produitVue latérale Vue avantRayon de basculement avant Dimensionspourle pivotement des portesRayon debasculement Modèles deDégagementspourlespoignées et portes Série Overlay Panneau Panneaux personnalisés de la Série Classic Ensembles de panneaux dorigine de la série ClassicPoignée standard Vue supérieure Panneaux de porte pour modèles avec distributeurExigences dusinage du panneau de la grille supérieure Exigences dusinage des panneaux de portePanneaux de soutien Modèle Panneaux personnalisés de la série OverlayPanneaux latéraux personnalisés de la Série Overlay Outillage etpiècesnécessaires Exigences ’INSTALLATIONModèle Largeur a tel quillustré ci-dessus Exigences d’emplacementDimensions de l’ouverture Supérieure. Voir Dimensions de l’ouvertureArrivée d’eau froide Méthode recommandée de mise à la terreSpécifications électriques Spécifications de l’alimentation en eauSéries Classic et Overlay Instructions D’INSTALLATIONDéballage du réfrigérateur Réduction du rayon de basculementSérie Pro Line Installation de planchesantibasculementInstallation des planches antibasculement Série ArchitectStyle 1 Raccordement à la canalisation deau Déplacementdu réfrigérateurà Lemplacement finalRaccordementde la canalisation d’eau Brancherle réfrigérateurPanneaux de porte Installation des panneaux personnalisés de la Série ClassicDéploiement despiedsde nivellement Installation des panneaux de porte Installation despanneaux personnalisés de la Série OverlayTringle supérieure Enlèvement des portes Suivre les étapes suivantes pour réinstaller la porteNivellementdu réfrigérateur Ajustementetenlèvement desportesModèles Overlay Installation du panneau latéralAjustement de l’ouverture des portes Acheverl’installation Installation de la grille de la baseAll rights reserved 2266811A
Related manuals
Manual 23 pages 20.17 Kb

Refrigerator specifications

The KitchenAid 338 Refrigerator, model 4KSRF42D, is an exemplary appliance that combines functionality with a sleek design, making it a prime choice for modern kitchens. This refrigerator offers an impressive blend of features, technologies, and characteristics that elevate food storage and preservation.

One of the standout features of the 4KSRF42D is its spacious interior. With a total capacity that accommodates a significant amount of groceries, this refrigerator ensures that there is ample room for all your food items and beverages. Configured with adjustable shelves and spacious bins, organization and access to your favorite foods are simple and efficient.

The refrigerator incorporates the innovative Preserva Food Care System. This advanced technology utilizes dual cooling systems that maintain optimal humidity levels and temperature, helping to keep fruits and vegetables fresher for longer periods. The system cleverly prevents the transfer of odors between the refrigerator and freezer, ensuring that your food maintains its intended flavor.

Another notable characteristic of the KitchenAid 338 is its sleek stainless-steel exterior, which not only looks modern but is also easy to clean. The fingerprint-resistant finish helps keep the appliance looking immaculate, even in bustling kitchen environments. Additionally, the countertop depth design means it seamlessly integrates into kitchen cabinetry for a built-in look.

Energy efficiency is a key consideration for modern consumers, and the 4KSRF42D excels in this regard as it meets Energy Star certification standards. This ensures minimal energy consumption without compromising on performance, ultimately reducing your utility bills while being environmentally friendly.

The refrigerator is equipped with a sophisticated ice maker located in the freezer compartment. This feature means you always have a reliable supply of ice at hand for those hot summer days or entertaining guests. The easy-to-access water dispenser on the exterior front allows for instant hydration with filtered water.

In terms of digital technology, the KitchenAid 338 comes with an intuitive LCD display that allows users to easily monitor and adjust temperature settings in both compartments. Smart functionality ensures that users can even receive alerts to changes in temperature through mobile notifications, offering added convenience.

Overall, the KitchenAid 338 Refrigerator, model 4KSRF42D, is a culmination of advanced features and elegant design. Its emphasis on preserving food quality, energy efficiency, and user-friendly technology makes it an excellent addition to any contemporary kitchen. Whether you are an avid home chef or simply looking to upgrade your kitchen appliances, this refrigerator constitutes a worthy investment that promises reliability and aesthetic appeal.