Clarion installation manual APX200.2M Power System Amplifier

Page 10

APX200.2M Power System Amplifier

5.Add an external fuse on the amplifier's positive (+) power lead and connect it as close as possible to the vessel's (+) battery terminal. Use a rating that equals the total current consumption at full output of all amplifiers in the system. Adding an external fuse will protect the electrical system from short circuits that can cause a fire.

6.Refer to Figure 6 when making electrical connections. Connect the amplifier's positive (+) lead via a fuse directly to the positive (+) terminal on

the battery. Do not connect this wire to the vessel's fuse panel. Use red-insulated 10-gauge (or larger) wire for the amplifier's positive (+) power lead

and the same-gauge black-insulated wire for the ground.

7.When replacing the amplifier 's fuse, always use one having the same current rating. Substituting a higher-rated fuse or a slow-blow type can result in serious damage to the amplifier.

8.Make sure that your vessel's electrical system (alternator, battery, etc.) is capable of handling the additional load. If you are planning a multi-amplifier system, you may need to add a second battery and possibly upgrade the alternator with a higher-output rated model. Consult your authorized Clarion dealer for recommendations.

9.To avoid noise problems, run the amplifier's positive (+) power lead along

one side of the vessel to the battery. Run the remote turn-on wire and RCA audio cables down the center, and route the speaker wires along the remaining side. If wires must cross, run them perpendicular to each other.

10.When creating passage holes for the power wire, use grommets to eliminate any sharp edges created during drilling. This will protect the wire from being nicked and causing a short circuit.

11.Extra cable can cause signal loss and act as an "antenna" for noise. Use only high-quality RCA cables that are no longer than necessary to make a direct connection with the source unit or equalizer.

8

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Operational Installation Manual Table of Contents About the Manual and WarrantyIntroduction Description Input Connections and Audio ControlsHigh-pass/Low-pass Filter Controls Connections for Power and Speakers Applications Channel Full-Range, Satellite, or Subwoofer Stereo System Mixed-Mode Satellite and Subwoofer System Mounting Precautions InstallationWiring Precautions APX200.2M Power System Amplifier Electrical connections for the APX200.2M Setting the Crossover Setting the GainSetting the Bass Boost Troubleshooting Final System ChecksProduct Specs APX200.2MPage APX200.2M-10 Rev.1 03/01

APX200 specifications

The Clarion APX200 is an advanced mobile audio processing unit designed to enhance the audio experience in vehicles. Renowned for its exceptional sound quality and innovative technologies, the APX200 represents the cutting-edge of in-car entertainment solutions.

One of the standout features of the APX200 is its multi-channel configuration, allowing users to connect up to 16 channels of output. This flexibility enables the setup of complex audio systems tailored to individual preferences and vehicle acoustics. With a built-in digital signal processor (DSP), the APX200 provides extensive tuning capabilities, giving users the power to adjust parameters such as equalization, crossover settings, and time alignment for optimal sound staging.

The device supports high-resolution audio formats, ensuring that every nuance of the music is reproduced with fidelity. Users can take advantage of its high-performance DACs, which convert digital audio signals into analog with stunning clarity. The APX200 is also equipped with advanced noise-cancelling technology, reducing background noise and enhancing overall listening quality.

Another impressive aspect of the Clarion APX200 is its user-friendly interface. The unit features an intuitive touchscreen display that allows for easy navigation through settings and adjustments. The built-in Bluetooth functionality enables wireless streaming, allowing users to play music from their smartphones or other devices seamlessly.

The APX200 is designed with installation flexibility in mind. Its compact size and versatile mounting options make it suitable for a range of vehicle types without taking up unnecessary space. The robust build quality ensures durability, allowing the unit to withstand the rigors of daily use.

In addition to sound quality and ease of use, the Clarion APX200 incorporates advanced connectivity options. It includes multiple input types, including auxiliary and USB inputs, enabling users to connect various audio sources without hassle.

In summary, the Clarion APX200 is a top-tier mobile audio processor offering a rich feature set designed to elevate any in-car audio experience. With its powerful DSP, high-resolution audio support, and user-friendly interface, it stands out as a formidable choice for automotive audio enthusiasts looking to create their perfect soundscape. Whether enjoying music on a long drive or setting up a custom audio system, the APX200 provides the tools necessary for an unparalleled listening experience.
Top Page Image Contents