Clarion APX200 installation manual High-pass/Low-pass Filter Controls

Page 4

APX200.2M Power System Amplifier

•Gain Control - This allows you to set the nominal operating level of the amplifier. The amplifier's range, 250mV to 2.5V for RCA inputs or 500mV to

5V for speaker level inputs, can accommodate input levels from virtually any brand of source unit.

•Bass Boost Control- The amplifier also features a "high-Q" (i.e. narrow frequency band) Bass Boost circuit. It acts much like an equalizer, with adjustable gain (from 0 to +18dB) fixed at 45Hz. Use this feature to tune low-fre- quency audio response to compensate for a less than ideal subwoofer enclosure design. The added boost produces rich, full bass tones that are normally difficult to reproduce in the car audio environment. NOTE: If Bass Boost is undesirable, set Bass Boost to 0dB.

High-pass/Low-pass Filter Controls

•Frequency (Hz) Selection Control - The crossover frequency is fully adjustable between 55Hz and 5500Hz (via the Crossover Frequency Multiplier) for a wide range of crossover points. Use this feature, along with your speaker manufacturer's recommended crossover frequencies, to quickly design a more advanced system (see Applications on page 5.) NOTE: If the X-Over Mode Switch is set to OFF, varying the Freq (Hz) Control will produce no effect.

•Crossover Frequency Multiplier Switch - When engaged, this switch increases the crossover frequency by a factor of 10. Example: If the Freq (Hz) dial is set for 240 Hz, pushing in the Multiplier Switch changes the setting to 2400 Hz.

•X-Over Mode Switch - This switch is equipped with a 12dB per octave electronic filter for precise frequency attenuation with minimal phase distortion. The steep crossover slope keeps midrange tones out of the subwoofer and thereby eliminates an unnatural "nasal" tone quality in the audio system. A filter is activated by sliding the X-Over Mode Switch to either LP or HP.

•Input Mode Switch - This switch allows you to set the input mode. Stereo input allows full left and right stereo operation. Right (bridged) input allows

single channel input for bridged operation. This is especially useful in high-powered systems when using one amplifier for each subwoofer/speaker. L + R

(sum mono) allows a stereo input to be summed into a mono output.

•Speaker Level Inputs - These provide connections for a high-level stereo source. In addition, these connections are provided for installations where the source unit's RCA outputs are unavailable.

WARNING: When using the speaker (high-level) inputs, the Black wire must be grounded at the Radio. Failure to do this will result in noise and improper operation.

2

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Operational Installation Manual Table of Contents About the Manual and WarrantyIntroduction Description Input Connections and Audio ControlsHigh-pass/Low-pass Filter Controls Connections for Power and Speakers Applications Channel Full-Range, Satellite, or Subwoofer Stereo System Mixed-Mode Satellite and Subwoofer System Mounting Precautions InstallationWiring Precautions APX200.2M Power System Amplifier Electrical connections for the APX200.2M Setting the Crossover Setting the GainSetting the Bass Boost Troubleshooting Final System ChecksProduct Specs APX200.2MPage APX200.2M-10 Rev.1 03/01

APX200 specifications

The Clarion APX200 is an advanced mobile audio processing unit designed to enhance the audio experience in vehicles. Renowned for its exceptional sound quality and innovative technologies, the APX200 represents the cutting-edge of in-car entertainment solutions.

One of the standout features of the APX200 is its multi-channel configuration, allowing users to connect up to 16 channels of output. This flexibility enables the setup of complex audio systems tailored to individual preferences and vehicle acoustics. With a built-in digital signal processor (DSP), the APX200 provides extensive tuning capabilities, giving users the power to adjust parameters such as equalization, crossover settings, and time alignment for optimal sound staging.

The device supports high-resolution audio formats, ensuring that every nuance of the music is reproduced with fidelity. Users can take advantage of its high-performance DACs, which convert digital audio signals into analog with stunning clarity. The APX200 is also equipped with advanced noise-cancelling technology, reducing background noise and enhancing overall listening quality.

Another impressive aspect of the Clarion APX200 is its user-friendly interface. The unit features an intuitive touchscreen display that allows for easy navigation through settings and adjustments. The built-in Bluetooth functionality enables wireless streaming, allowing users to play music from their smartphones or other devices seamlessly.

The APX200 is designed with installation flexibility in mind. Its compact size and versatile mounting options make it suitable for a range of vehicle types without taking up unnecessary space. The robust build quality ensures durability, allowing the unit to withstand the rigors of daily use.

In addition to sound quality and ease of use, the Clarion APX200 incorporates advanced connectivity options. It includes multiple input types, including auxiliary and USB inputs, enabling users to connect various audio sources without hassle.

In summary, the Clarion APX200 is a top-tier mobile audio processor offering a rich feature set designed to elevate any in-car audio experience. With its powerful DSP, high-resolution audio support, and user-friendly interface, it stands out as a formidable choice for automotive audio enthusiasts looking to create their perfect soundscape. Whether enjoying music on a long drive or setting up a custom audio system, the APX200 provides the tools necessary for an unparalleled listening experience.
Top Page Image Contents