Clarion APX200 installation manual Installation, Mounting Precautions, Wiring Precautions

Page 9

OWNER’S MANUAL

INSTALLATION

This section lists Mounting and Wiring Precautions for installing a Clarion APX200.2M marine amplifier. Combined with the experience of a professional installer, these safeguards provide enough detail to successfully complete an installation. If you do not have the necessary skills, do not install the amplifier yourself. Instead, see your authorized Clarion dealer for installation recommendations.

MOUNTING PRECAUTIONS

Although the Clarion APX200.2M incorporates heat sinks and protection circuits, mounting the amplifier in a tight space without any air movement can still damage internal circuitry over time. Choose a site that provides adequate ventilation and is isolated from the marine environment. For easy system set-up, mount the amplifier so the front panel controls will be accessible after installation.

In addition, observe the following precautions:

1.For the most efficient cooling, mount the amplifier so cool air runs along the length of the fins rather than across them. Remember, any moving air will dissipate heat.

2.Mount the amplifier on a rigid surface. Avoid mounting to subwoofer enclosures or areas prone to vibration.

3.Prior to drilling, make sure proposed mounting holes will not cut into the fuel tank, fuel lines, or electrical wiring.

WIRING PRECAUTIONS

Read all wiring precautions. If you are not sure of the connections, contact your authorized Clarion dealer.

1.Before installation, make sure the source unit Power switch is in the OFF position.

2.Disconnect the negative (-) lead of the battery before making any power connections.

3.When making connections, be sure that each connection is clean and secure. Insulate final connections with electrical tape or shrink tubing. Failure to do so may damage your equipment.

4.A secure clean ground connection is critical to the performance of your Clarion amplifier. Use the shortest ground wire possible and securely connect to the vessel battery to minimize resistance and avoid noise problems.

7

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Operational Installation Manual About the Manual and Warranty Table of ContentsIntroduction Input Connections and Audio Controls DescriptionHigh-pass/Low-pass Filter Controls Connections for Power and Speakers Applications Channel Full-Range, Satellite, or Subwoofer Stereo System Mixed-Mode Satellite and Subwoofer System Installation Mounting PrecautionsWiring Precautions APX200.2M Power System Amplifier Electrical connections for the APX200.2M Setting the Gain Setting the CrossoverSetting the Bass Boost Final System Checks TroubleshootingAPX200.2M Product SpecsPage APX200.2M-10 Rev.1 03/01

APX200 specifications

The Clarion APX200 is an advanced mobile audio processing unit designed to enhance the audio experience in vehicles. Renowned for its exceptional sound quality and innovative technologies, the APX200 represents the cutting-edge of in-car entertainment solutions.

One of the standout features of the APX200 is its multi-channel configuration, allowing users to connect up to 16 channels of output. This flexibility enables the setup of complex audio systems tailored to individual preferences and vehicle acoustics. With a built-in digital signal processor (DSP), the APX200 provides extensive tuning capabilities, giving users the power to adjust parameters such as equalization, crossover settings, and time alignment for optimal sound staging.

The device supports high-resolution audio formats, ensuring that every nuance of the music is reproduced with fidelity. Users can take advantage of its high-performance DACs, which convert digital audio signals into analog with stunning clarity. The APX200 is also equipped with advanced noise-cancelling technology, reducing background noise and enhancing overall listening quality.

Another impressive aspect of the Clarion APX200 is its user-friendly interface. The unit features an intuitive touchscreen display that allows for easy navigation through settings and adjustments. The built-in Bluetooth functionality enables wireless streaming, allowing users to play music from their smartphones or other devices seamlessly.

The APX200 is designed with installation flexibility in mind. Its compact size and versatile mounting options make it suitable for a range of vehicle types without taking up unnecessary space. The robust build quality ensures durability, allowing the unit to withstand the rigors of daily use.

In addition to sound quality and ease of use, the Clarion APX200 incorporates advanced connectivity options. It includes multiple input types, including auxiliary and USB inputs, enabling users to connect various audio sources without hassle.

In summary, the Clarion APX200 is a top-tier mobile audio processor offering a rich feature set designed to elevate any in-car audio experience. With its powerful DSP, high-resolution audio support, and user-friendly interface, it stands out as a formidable choice for automotive audio enthusiasts looking to create their perfect soundscape. Whether enjoying music on a long drive or setting up a custom audio system, the APX200 provides the tools necessary for an unparalleled listening experience.
Top Page Image Contents