Temperature and Moisture, Ice and Water

■Is the dispenser light set to NIGHT LIGHT or AUTO? If the dispenser is set to the NIGHT LIGHT or AUTO mode, be sure the dispenser light sensor is not blocked. See “Water and Ice Dispensers.”

Temperature and Moisture

Temperature is too warm

■New installation? Allow 24 hours following installation for the refrigerator to cool completely.

■Door(s) opened often or left open? Allows warm air to enter refrigerator. Minimize door openings and keep doors fully closed.

■Large load of food added? Allow several hours for refrigerator to return to normal temperature.

■Controls set correctly for the surrounding conditions? Adjust the controls a setting colder. Check temperature in 24 hours. See “Using the Controls.”

There is interior moisture buildup

NOTE: Some moisture build-up is normal.

■Humid room? Contributes to moisture build-up.

■Door(s) opened often or left open? Allows humid air to enter refrigerator. Minimize door openings and keep doors fully closed.

Ice and Water

The ice maker is not producing ice or not enough ice

■Refrigerator connected to a water supply and the supply shutoff valve turned on? Connect refrigerator to water supply and turn water shutoff valve fully open.

■Kink in the water source line? A kink in the line can reduce water flow. Straighten the water source line.

■Ice maker turned on? Make sure wire shutoff arm or switch (depending on model) is in the ON position.

■New installation? Wait 24 hours after ice maker installation for ice production to begin. Wait 72 hours for full ice production.

■Large amount of ice recently removed? Allow 24 hours for ice maker to produce more ice.

■Ice cube jammed in the ice maker ejector arm? Remove ice from the ejector arm with a plastic utensil.

■Reverse osmosis water filtration system connected to your cold water supply? This can decrease water pressure. See “Water Supply Requirements” in either the Installation Instruction booklet or the Use & Care Guide.

The ice cubes are hollow or small

NOTE: This is an indication of low water pressure.

■Water shutoff valve not fully open? Turn the water shutoff valve fully open.

■Kink in the water source line? A kink in the line can reduce water flow. Straighten the water source line.

■Reverse osmosis water filtration system connected to your cold water supply? This can decrease water pressure. See “Water Supply Requirements.”

■Questions remain regarding water pressure? Call a licensed, qualified plumber.

Off-taste, odor or gray color in the ice

■New plumbing connections? New plumbing connections can cause discolored or off-flavored ice.

■Ice stored too long? Discard ice. Wash ice bin. Allow 24 hours for ice maker to make new ice.

■Odor transfer from food? Use airtight, moisture proof packaging to store food.

■Are there minerals (such as sulfur) in the water? A water filter may need to be installed to remove the minerals.

■Is there a water filter installed on the refrigerator? Gray or dark discoloration in ice indicates that the water filtration system needs additional flushing.

The ice dispenser will not operate properly

■Freezer door closed completely? Close the door firmly. If it does not close completely, see “The doors will not close completely.”

■Ice bin installed correctly? Be sure the ice bin is firmly in position.

■New installation? Wait 24 hours after ice maker installation for ice production to begin. Wait 72 hours for full ice production.

■Ice stuck in the delivery chute? Use a plastic utensil to clear the delivery chute.

■Has the wrong ice been added to the bin? Use only cubes produced by the current ice maker.

■Has the ice melted around the auger (metal spiral) in the ice bin? Dump the ice cubes and clean the ice bin.

WARNING

Cut Hazard

Use a sturdy glass when dispensing ice or water.

Failure to do so can result in cuts.

■Is the ice dispenser stalling while dispensing “crushed” ice? Change the ice button from “crushed” to “cubed.” If cubed ice dispenses correctly, depress the button for “crushed” ice and begin dispensing again.

■Has the dispenser arm been held in too long? Ice will stop dispensing when the arm is held in too long. Wait 3 minutes for dispenser motor to reset before using again.

The water dispenser will not operate properly

■Freezer door closed completely? Close the door firmly. If it does not close completely, see “The doors will not close completely.”

■Refrigerator connected to a water supply and the supply shutoff valve turned on? Connect refrigerator to water supply and turn water shutoff valve fully open.

■Is the water pressure at least 30 psi? The water pressure to the home determines the flow from the dispenser. See “Water Supply Requirements.”

■Kink in the home water source line? Straighten the water source line.

KSRN25FRWH00, KSRF25FRBT00, KSRF25FRBT01, KSRN25FRSS01, 2308392 specifications

The KitchenAid appliance line has become synonymous with high-quality kitchen solutions, and models such as the KSRF25FRWH00, KSRF25FRBL01, KSRF25FRBT01, KSRN25FRWH00, and KSRT25CRSS00 are no exception. Each model is designed with advanced refrigeration technology, aiming to enhance food preservation and user convenience.

One standout feature across these models is the FreshSeal crisper drawers. These drawers are engineered to maintain optimal humidity levels, ensuring that fruits and vegetables stay fresh for longer periods. The adjustable temperature controls allow users to customize their storage environment based on the specific needs of different food items.

The exterior design of these refrigerators showcases a sleek finish, with the KSRF25FRWH00 and KSRF25FRWH00 both featuring a traditional white finish, while the KSRF25FRBL01 and KSRF25FRBT01 offer stylish black options, catering to various kitchen aesthetics. The KSRT25CRSS00 model stands out with its stainless steel exterior, providing a modern and professional look that complements contemporary kitchen settings.

The convenience of storage is greatly enhanced through the use of adjustable shelving. Each model features glass shelves that can be easily repositioned to accommodate taller items, maximizing usable space. Additionally, the integrated LED lighting system ensures that every corner of the refrigerator is illuminated, making it easy to find what you need.

Another crucial aspect of these KitchenAid models is their energy efficiency. Equipped with Energy Star certification, they are designed to consume less electricity while still delivering optimum performance. This not only helps reduce household energy bills but also minimizes environmental impact.

Moreover, the advanced cooling system implemented in these refrigerators provides consistent temperature control and quick recovery after door openings. This feature helps in maintaining food quality and safety, essential for any kitchen enthusiast.

Overall, the KitchenAid KSRF25FRWH00, KSRF25FRBL01, KSRF25FRBT01, KSRN25FRWH00, and KSRT25CRSS00 models exemplify what modern refrigeration should be. With their emphasis on food preservation, energy efficiency, and design versatility, they serve as a reliable choice for all kitchen needs. Whether you prioritize fresh produce, energy savings, or a stylish look, these refrigerators deliver on multiple fronts to enhance your culinary experience.