KitchenAid W10331007B InstallRange Hood, Install Range HoodInternal BlowerMotor

Page 8

6.Remove terminal box cover and set aside.

7.Remove knockout from the back of the range hood and install a UL listed or CSA approved ¹⁄₂" (1.3 cm) strain relief.

8.Place the range hood near its mounting position and run the power supply cable through the strain relief into terminal box (enough to make connection).

9.Tighten the strain relief screws.

NOTE: Your range hood requires you to purchase either an internal type or an in-line (external type) blower motor system.

For internal blower systems, there are blower motor mounting parts in the blower motor installation packet that must be added to the range hood prior to mounting the range hood to the wall. See the “Install Range Hood Internal Blower Motor” section and the instructions supplied with the blower motor.

InstallRange Hood

The range hood attaches to the wall by the 2 mounting screws in the wood support mounted to the wall in the “Range Hood Mounting Screws Installation” section.

1.Using 2 or more people, hang the range hood on the wall by placing the slotted holes in the range hood back over the

2 screws mounted to the wood support mounted to the wall.

NOTE: If your installation uses the optional duct cover, the vent system needs to be connected to the range hood and the duct cover mounted to the top of the range hood before tightening the mounting screws. See steps 3 - 5.

→

→

Install Range HoodInternal BlowerMotor

NOTE: Your range hood requires you to purchase either an internal type or an in-line (external type) blower motor system. See “Blower Motor System” in the “Accessories” section.

The internal blower system can be mounted for top venting or rear venting. For top venting, the mounting bracket and spring clip that comes with the blower system will mount to the top panel of the range hood. For rear venting, the mounting bracket and spring clip that comes with the blower system will mount to the rear panel of the range hood.

Prepare the Internal Blower System

IMPORTANT: Perform steps 1-4 before mounting the range hood.

1.Remove grease filters from range hood. See the “Range Hood Care” section in the Use and Care Guide.

2.Install the motor support bracket using three 4.2 x 8 mm screws. Screw bracket to the inside top or back (alternate location on some models), toward the left side of the range hood.

3.Install motor spring clip using two 4.2 x 8 mm screws. Screw spring clip to the inside top or back (alternate location on some models) of the range hood at the proper location for the selected motor system. Slide the mounting tab of the spring clip through the slot in the panel and secure with the screws. Use the inside set of mounting holes for the single motor system. Use the outside set of mounting holes for the dual motor system.

B

A

2.Push the range hood up into the narrow slots, align the bottom of the hood to the horizontal line, level the hood, and tighten the 2 mounting screws.

3.Mark 2 lower mounting hole center point locations. Drill

¹⁄₈" (0.32 cm) pilot holes if the holes are located into wood. If holes are not located into wood, drill two ³⁄₈" (0.95 cm) pilot holes and insert 10 x 50 mm wall anchors. Install 2 - 6 x

80 mm screws with D5.3 x 20 mm washers into the lower mounting anchors and tighten.

4.Install 4 - 4.2 x 19 mm screws through the back of the hood into the wood support and tighten.

5.Connect vent system to hood. Seal all joints with clamps.

NOTE: If your installation uses the optional full-width duct cover, attach the duct cover to the top of the range hood following the instructions and using the screws that are provided with the duct cover. For information on ordering the optional duct cover, see the “Accessories” section.

D E

C

A. 4.2 x 8 mm screws (3) for motor support bracket B. 4.2 x 8 mm screws (2) for motor spring clip

C. Motor support bracket

D. Motor spring clip (single motor assembly location) E. Motor spring clip (dual motor assembly location)

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Commercial Style WALL-MOUNT Canopy Range Hood Table of Contents Range Hood SafetyTools needed Installation RequirementsTools and Parts Product Dimensions Location RequirementsParts needed Parts suppliedMakeup air Cold weather installationsVenting Requirements Typical In-line Blower Motor System Venting Installations Electrical RequirementsCalculating Vent System Length Example vent systemInstallation Instructions Range Hood Mounting Screws InstallationPrepareLocation Complete PreparationPrepare the Internal Blower System InstallRange HoodInstall Range HoodInternal BlowerMotor Dual Blower Motor Assembly Install Range Hood Internal Blower MotorSingle Blower Motor Assembly Prepare the In-line Blower System InstallRange Hood In-Line ExternalType BlowerMotorPrepare for Mounting the In-Line Blower System Inlet Side Install In-line Blower SystemOutlet Side MakeElectrical Connectionsfor In-Line BlowerMotor System Electrical Connection Inside In-line Blower SystemMakeElectricalPower Supply Connection to Range Hood RangeHood Controls Complete InstallationandCheck OperationRange Hood USE RangeHoodLamps CleaningRange Hood Care Wiring Diagram SE112AAssistance or Service AccessoriesIntheU.S.A InCanadaKitchenaid Ventilation Warranty This limited warranty does not coverSécurité DE LA Hotte DE Cuisinière Votre sécurité et celle des autres est très importanteImportantes Instructions DE Sécurité Outillageetpièces Exigences DinstallationExigences demplacement Dimensions d’installation Vue arrièreInstallations pour régions à climat froid Exigences concernant lévacuationAir dappoint Pour un fonctionnement efficace et silencieuxSpécificationsélectriques Calcul de la longueur effective du circuit dévacuationExemple de système de décharge Composant Longueur équivalenteInstructions D’INSTALLATION PréparationdelemplacementInstallation des vis de montage de la hotte Achever la préparationPréparation du système de ventilation interne Installationdela hotteInstallation du moteurduventilateurinterne Delahotte Ensemble à deux moteurs-ventilateurs Installer le moteur du ventilateur interne de la hotteEnsemble à un seul moteur-ventilateur Préparation du système de ventilation en ligne Installationdumoteurduventilateurenligne Externe dela hottePréparation du montage du système de ventilation en ligne Côté entrée Installation du système de ventilation en ligneCôté sortie La hotte étant montée voir la section Instructions Connexion de l’alimentationélectriqueà la Hotte Utilisation DE LA Hotte Achever linstallation et vérifierle FonctionnementCommandes delahotte decuisinière Nettoyage Entretien DE LA Hotte DE CuisinièreLampesdela hotte decuisinière Schéma DE Câblage MARAuCanada Assistance OU ServiceAccessoires W10331007B Garantie DU Système DE Ventilation KitchenaidLa présente garantie limitée ne couvre pas

W10331007B specifications

The KitchenAid W10331007B is a versatile and essential addition to any kitchen, designed to enhance both functionality and convenience. This product combines traditional craftsmanship with modern technology, making it an indispensable tool for culinary enthusiasts and home bakers alike.

One of the standout features of the W10331007B is its powerful motor, which ensures consistent performance whether you're mixing dough, whipping cream, or blending ingredients. The motor's high efficiency allows for quiet operation, making it suitable for early morning baking sessions or late-night meal preparations without disturbing the household.

This model is equipped with a range of attachments that expand its capabilities far beyond that of a standard mixer. From the flat beater for mixing batters to the dough hook for kneading, every attachment is designed to provide optimal results. Additionally, the inclusion of a wire whip makes it easy to achieve fluffy meringues or whipped cream, catering to a variety of recipes and culinary techniques.

The W10331007B boasts a user-friendly design with intuitive controls that allow for precise speed adjustments. Users can select from multiple speeds to suit their tasks, ensuring that delicate ingredients are treated with care while sturdier mixtures are thoroughly combined. This versatility empowers cooks to achieve professional-quality results with minimal effort.

Built with durability in mind, the KitchenAid W10331007B features a robust construction that stands up to frequent use. The stainless steel components not only ensure longevity but also make cleanup a breeze. The removable parts are dishwasher safe, allowing for quick maintenance and more time spent enjoying culinary creations rather than scrubbing dishes.

Another remarkable characteristic of the W10331007B is its iconic design. Offered in a variety of colors, it can seamlessly blend into any kitchen decor or serve as a stylish focal point on countertops. This aesthetic appeal, combined with its high functionality, makes it an excellent choice for both cooking aficionados and casual users.

In summary, the KitchenAid W10331007B embodies the perfect balance of form and function. Its powerful motor, versatile attachments, user-friendly controls, and durable construction make it a top choice for anyone looking to elevate their cooking or baking experience. Whether you're preparing a simple weekday dinner or an elaborate feast, this mixer is designed to meet your needs with ease and style.
Top Page Image Contents