Location Requirements

Parts needed

■1 UL or CSA listed, ¹⁄₂" (12.5 mm) strain relief

■2 UL listed wire connectors

■Home power supply cable

■4 Concrete anchors for ¹⁄₄" x 4" hex head lag bolts (for concrete installation)

For vented installations, you will also need:

■1 wall or roof cap

■Metal vent system

For non-vented (recirculating) installations, you will also need:

■Chimney Kit Part Number 8212716 (Stainless Steel), 8212717 (White), or 8212718 (Black). See “Assistance or Service” section to order.

■Charcoal Filter Kit Part Number 8285507 for non-vented (recirculating) installations only. See “Assistance or Service” section to order

Parts supplied

Remove parts from packages. Check that all parts were included.

■Literature package

■Hood canopy assembly with ventilator and light bulbs installed

■3 Filters

■Chimney assembly

■Ceiling template

■Mounting template

■Upper chimney cover

■Lower chimney cover

■Parts bag containing:

–Damper

–4 Mounting wood screws / 4 wood shelf bolts

–4 Wood shelf washers

–4 Wood shelf nuts

–4 Bolts to attach canopy to chimney

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located inside the range hood on the rear wall of the range hood.

Island hood location should be away from strong draft areas, such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance.

Grounded electrical outlet is required. See “Electrical Requirements” section.

It is recommended that the hood be fastened into solid wood.

The island hood is factory set for venting through the roof or wall. For non-vented (recirculating) installations see “Recirculating Installations” in “Install Chimney Covers” section.

All openings in ceiling and where island hood will be installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local codes.

Product Dimensions

Vented Installations

13³⁄₄"		12¹⁄₁₆"
(34.9 cm)		(30.6 cm)
(34.9 cm)		(30.6 cm)

26³⁄₈"

(65.1 cm)

min.

38¹⁄₂"

(97.8 cm)

23⁵⁄₈"max.

(60.0 cm)

3¹⁵⁄₁₆"

(10.0 cm)

27¹⁄₂"

36" (91.4 cm)

(69.9 cm)

Non-vented (recirculating) Installations

For non-vented (recirculating) installations, optional Recirculating Chimney Kit Part Number 8212718 (Black), Kit Part Number 8212716 (Stainless Steel) or Kit Part Number 8212717 (White) must be used. These kits include a new lower chimney cover (that replaces the lower chimney cover shipped with the island hood), a charcoal filter and a diverter.

13³⁄₄"		12¹⁄₁₆"
(34.9 cm)		(30.6 cm)
(34.9 cm)		(30.6 cm)

						26³⁄₈	"
						(65.1	cm)
						min.
3¹⁄₂"						38¹⁄₂	"
3¹⁄₂"						(97.8	cm)
(8.9 cm)				23⁵⁄	₈"	(97.8	cm)
(8.9 cm)						max.
						max.
	(60.0				cm)
12¹⁄₂"		5"
(31.8 cm)		5"
(31.8 cm)	(12.7		cm)

36"(91.4CM) ISLAND RANGE HOOD specifications

The KitchenAid 36" (91.4CM) Island Range Hood is an exceptional addition to any modern kitchen, combining functionality with sophisticated design. This hood is engineered to efficiently remove smoke, steam, and odors while enhancing the aesthetic appeal of your kitchen island setup.

One of the standout features of the KitchenAid Island Range Hood is its powerful ventilation system. With multiple speed settings, including a powerful boost function, it ensures optimal air circulation and keeps your kitchen environment fresh, regardless of the intensity of your cooking. The hood boasts a high CFM (cubic feet per minute) rating, allowing it to capture and vent even the most pungent cooking odors effectively.

The hood is designed with a sleek, stainless steel finish that complements any kitchen decor. Its modern appearance adds elegance and sophistication, making it not just a functional appliance, but also a statement piece in your kitchen. The adjustable duct cover allows for versatile installation heights, ensuring a perfect fit for various ceiling heights, making it an ideal choice for island installations.

Equipped with innovative technologies, the KitchenAid Island Range Hood features LED lighting that enhances visibility over your cooking area. The bright, energy-efficient lights illuminate your workspace without excessive heat, providing the right ambiance for culinary creativity. Additionally, it has a dishwasher-safe baffle filter, which traps grease and can be easily cleaned, ensuring the hood maintains its performance and appearance over time.

The hood also includes a convenient remote control feature, allowing you to adjust settings and switch the unit on and off from a distance. It integrates seamlessly with other KitchenAid appliances, creating a cohesive and modern kitchen environment.

Furthermore, noise levels are kept to a minimum, thanks to the hood’s design and advanced engineering, enabling you to enjoy a peaceful cooking experience. Whether you are a professional chef or a home cooking enthusiast, the KitchenAid 36" Island Range Hood offers the perfect blend of style, efficiency, and advanced technology—all essential elements for an exceptional cooking environment.