KitchenAid W10246119C Wire connection Power Supply Cord, Line 2 red Line 1 black

Page 11

4-wire connection: Power Supply Cord

Use this method for:

■New branch-circuit installations (1996 NEC)

■Mobile homes

■Recreational vehicles

■In an area where local codes prohibit grounding through the neutral.

1.Cut out and remove part of the metal ground strap (B).

A

B

C

A. Metal ground strap

B.Discard

C.Ground-link screw

2.Use a Phillips screwdriver to remove the ground-link screw from the back of the range. Save the ground-link screw and the end of the ground link under the screw.

3.Feed the power supply cord through the strain relief on the cord/conduit plate on bottom of range. Allow enough slack to easily attach the wiring to the terminal block.

A

B

C

D

A. Terminal block

B. Ground-link screw

C. UL listed strain relief

D. Power supply cord wires

4.Use a Phillips screwdriver to connect the green ground wire from the power supply cord to the range with the ground-link screw and ground-link section. The ground wire must be attached first.

5.Use ³⁄₈" nut driver to connect the neutral (white) wire to the center terminal block post with one of the 10–32 hex nuts.

A

F

 

B

 

C

E

 

 

D

A. 10–32 hex nut

D. Green ground wire

B. Ground-link screw

E. Neutral (center) wire

C. Line 2 (red)

F. Line 1 (black)

6.Connect line 2 (red) and line 1 (black) wires to the outer terminal block posts with 10-32 hex nuts.

7.Securely tighten hex nuts.

NOTE: For power supply cord replacement, use only a power cord rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with nominal 1³⁄₈" (3.5 cm) diameter connection opening, with ring terminals and marked for use with ranges.

8.Tighten strain relief screws.

9.Replace terminal block access cover.

3-wire connection: Power Supply Cord

Use this method only if local codes permit connecting chassis ground conductor to neutral wire of power supply cord.

1.Feed the power supply cord through the strain relief on the cord/conduit plate on bottom of range. Allow enough slack to easily attach the wiring to the terminal block.

A

B

C

D

A. Terminal block

B.Ground-link screw

C.UL listed strain relief

D.Power supply cord wires - large opening

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents W10246119C Table of Contents/Table des matièresTable DES Matières Range SafetyLocation Requirements Installation RequirementsToolsandParts Slide-in Range Mobile Home Additional Installation RequirementsProduct Dimensions Freestanding Range Mobile home installations requireElectrical Connection Cabinet DimensionsElectrical Requirements U.S.A.Only Electrical Requirements -CanadaOnly If connecting to a 4-wire systemIf connecting to a 3-wire system Local codes may permit the use of a UL listed, 3-wireSlide-In Ranges Installation InstructionsCountertopPreparation Measurefor Proper Height Unpack RangeFreestanding Ranges Adjust LevelingLegsInstall Anti-TipBracket Electrical Connection -U.S.A.Only Power Supply CordDirect Wire Style 1 Power supply cord strain reliefAssemble a UL listed strain relief in the opening Tighten strain relief screw against the power supply cordStyle 2 Direct wire strain relief Disconnect or Direct wire Circuit breaker BoxLine 2 red Line 1 black Wire connection Power Supply CordHex nut Green ground wire Ground-link screw Metal ground strap Discard Ground-link screwHex nut Direct Wire Installation Copper or Aluminum WireWire Connection Direct Wire Bare green ground wireGauge copper Lbs-in .8 N-m Gauge aluminum Lbs-in .0 N-m Bare Wire Torque SpecificationsWire Awg Torque Movingthe Range Complete InstallationVerify Anti-Tip BracketLocation Level RangeFor direct-wired ranges For power supply cord-connected rangesOutillage nécessaire Exigences DinstallationSécurité DE LA Cuisinière Outillage et piècesLors de l’utilisation d’un cordon d’alimentation électrique Exigences demplacementPièces nécessaires Planchette de remplissage arrière facultativeCuisinière coulissante Dimensions du produit Cuisinière autoportanteLargeur min. de louverture 30 76,2 cm Dimensions du placardCuisinière coulissante Déballage dela cuisinière Instructions DinstallationSpécifications électriques PréparationduplandetravailCuisinières coulissantes Installation dela brideantibasculementMesurespourunehauteurappropriée Ajuster les pieds de nivellementFixer le gabarit avec du ruban adhésif Vérification de lemplacement delabride AntibasculementSi la cuisinière ne fonctionne pas, contrôler ce qui suit Acheverl’installationRéglage delaplomb de lacuisinière Cuisinières alimentées par cordon dalimentation Déplacement delacuisinière

W10246119C specifications

The KitchenAid W10246119C is a versatile and essential kitchen appliance designed to enhance culinary experiences. This model focuses on providing efficiency and convenience for both amateur cooks and seasoned chefs.

One of its standout features is its powerful motor, which delivers optimum performance across a wide range of tasks. This motor is designed for durability and longevity, ensuring that users can rely on it for years to come. Coupled with a variety of attachments, the W10246119C allows users to tackle everything from mixing and blending to kneading and whipping, making it an invaluable addition to any kitchen.

The appliance typically incorporates several speed settings, allowing for precise control over mixing. This feature is crucial for achieving the perfect texture when preparing ingredients, be it for baking or cooking. Whether you need a slow stir for delicate mixtures or high-speed whipping for cream and egg whites, the W10246119C offers the flexibility required.

Technologically, the KitchenAid W10246119C often includes a user-friendly interface, featuring simple controls that make operation straightforward. The design is elegant, usually available in various colors to complement any kitchen décor. Additionally, its compact build ensures that it can fit comfortably on any countertop without taking up excessive space.

Another noteworthy characteristic is the appliance’s ease of cleaning. Many components are dishwasher-safe, simplifying the post-cooking cleanup process. The robust construction of the attachments also means they are built to withstand regular use, ensuring that the appliance remains a staple in the kitchen.

Furthermore, this model is often equipped with safety features, such as a locking mechanism, to prevent accidental operation. This is particularly beneficial when handling large quantities of ingredients or when using higher speeds.

In conclusion, the KitchenAid W10246119C combines power, versatility, and ease of use, making it an excellent tool for anyone looking to elevate their culinary skills. With its robust motor, multiple speed options, and range of attachments, it has become a trusted appliance in kitchens around the world, promising consistent results and effortless operation. Whether you are preparing a holiday feast or a simple weeknight dinner, the W10246119C stands ready to assist in creating delicious meals.
Top Page Image Contents