KitchenAid W10246119C Direct Wire Installation Copper or Aluminum Wire, Hex nut

Page 12

2.Use ³⁄₈" nut driver to connect the neutral (white) wire to the center terminal block post with one of the 10–32 hex nuts.

A

E

 

B

D

 

C

 

A. 10–32 hex nut

D. Neutral (white) wire

B. Line 2 (red)

E. Line 1 (black)

C.Ground-link screw

3.Connect line 2 (red) and line 1 (black) wires to the outer terminal block posts with 10-32 hex nuts.

4.Securely tighten hex nuts.

NOTE: For power supply cord replacement, use only a power cord rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with nominal 1³⁄₈" (3.5 cm) diameter connection opening, with ring terminals and marked for use with ranges.

5.Tighten strain relief screws.

6.Replace terminal block access cover.

Direct Wire Installation: Copper or Aluminum Wire

This range may be connected directly to the fuse disconnect or circuit breaker box. Depending on your electrical supply, make the required 3-wire or 4-wire connection.

1.Strip outer covering back 3" (7.6 cm) to expose wires. Strip the insulation back ³⁄₈" (1.0 cm) from the end of each wire.

³⁄₈"

(1.0 cm)

3"

(7.6 cm)

2.Allow enough slack in the wire to easily attach the wiring terminal block.

3.Complete electrical connection according to your type of electrical supply (4-wire or 3-wire connection).

1.Cut out and remove part of the metal ground strap (B).

A

B

C

A. Metal ground strap

B.Discard

C.Ground-link screw

2.Use a Phillips screwdriver to remove the ground-link screw from the back of the range. Save the ground-link screw and the end of the ground link under the screw.

3.Pull the wires through the strain relief on bottom of range. Allow enough slack to easily attach wiring to the terminal block.

A

 

 

B

 

 

C

D

 

G

 

 

E

F

 

 

 

A. Terminal block

 

E. Line 2 (red) wire

B. Ground-link screw

 

F. Neutral (white) wire

C. Cord/conduit plate

 

G. Line 1 (black) wire

D. Bare (green) ground wire

 

4.Attach terminal lugs to line 1 (black), neutral (white), and line 2 (red) wires. Loosen (do not remove) the setscrew on the front of the terminal lug and insert exposed wire end through bottom of terminal lugs. Securely tighten setscrew to torque as shown in the following Bare Wire Torque Specifications chart.

A

4-wire Connection: Direct Wire

Use this method for:

B

 

■New branch-circuit installations (1996 NEC)

■ Mobile homes

■ Recreational vehicles

CDE

■In an area where local codes prohibit grounding through the neutral

A. Terminal lug

B. Setscrew

C. Line 2 (red) wire

D. Neutral (white) wire

E. Line 1 (black) wire

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Table of Contents/Table des matières W10246119CRange Safety Table DES MatièresInstallation Requirements ToolsandPartsLocation Requirements Mobile Home Additional Installation Requirements Product Dimensions Freestanding RangeMobile home installations require Slide-in RangeCabinet Dimensions Electrical Requirements U.S.A.OnlyElectrical Connection If connecting to a 4-wire system If connecting to a 3-wire systemLocal codes may permit the use of a UL listed, 3-wire Electrical Requirements -CanadaOnlyInstallation Instructions CountertopPreparation Measurefor Proper HeightUnpack Range Slide-In RangesAdjust LevelingLegs Install Anti-TipBracketFreestanding Ranges Power Supply Cord Direct WireStyle 1 Power supply cord strain relief Electrical Connection -U.S.A.OnlyTighten strain relief screw against the power supply cord Style 2 Direct wire strain reliefDisconnect or Direct wire Circuit breaker Box Assemble a UL listed strain relief in the openingWire connection Power Supply Cord Hex nut Green ground wire Ground-link screwMetal ground strap Discard Ground-link screw Line 2 red Line 1 blackDirect Wire Installation Copper or Aluminum Wire Wire Connection Direct WireBare green ground wire Hex nutBare Wire Torque Specifications Wire Awg TorqueGauge copper Lbs-in .8 N-m Gauge aluminum Lbs-in .0 N-m Complete Installation Verify Anti-Tip BracketLocationLevel Range Movingthe RangeFor power supply cord-connected ranges For direct-wired rangesExigences Dinstallation Sécurité DE LA CuisinièreOutillage et pièces Outillage nécessaireExigences demplacement Pièces nécessairesPlanchette de remplissage arrière facultative Lors de l’utilisation d’un cordon d’alimentation électriqueDimensions du produit Cuisinière autoportante Cuisinière coulissanteDimensions du placard Cuisinière coulissanteLargeur min. de louverture 30 76,2 cm Instructions Dinstallation Spécifications électriquesPréparationduplandetravail Déballage dela cuisinièreInstallation dela brideantibasculement MesurespourunehauteurappropriéeAjuster les pieds de nivellement Cuisinières coulissantesVérification de lemplacement delabride Antibasculement Fixer le gabarit avec du ruban adhésifAcheverl’installation Réglage delaplomb de lacuisinièreSi la cuisinière ne fonctionne pas, contrôler ce qui suit Déplacement delacuisinière Cuisinières alimentées par cordon dalimentation

W10246119C specifications

The KitchenAid W10246119C is a versatile and essential kitchen appliance designed to enhance culinary experiences. This model focuses on providing efficiency and convenience for both amateur cooks and seasoned chefs.

One of its standout features is its powerful motor, which delivers optimum performance across a wide range of tasks. This motor is designed for durability and longevity, ensuring that users can rely on it for years to come. Coupled with a variety of attachments, the W10246119C allows users to tackle everything from mixing and blending to kneading and whipping, making it an invaluable addition to any kitchen.

The appliance typically incorporates several speed settings, allowing for precise control over mixing. This feature is crucial for achieving the perfect texture when preparing ingredients, be it for baking or cooking. Whether you need a slow stir for delicate mixtures or high-speed whipping for cream and egg whites, the W10246119C offers the flexibility required.

Technologically, the KitchenAid W10246119C often includes a user-friendly interface, featuring simple controls that make operation straightforward. The design is elegant, usually available in various colors to complement any kitchen décor. Additionally, its compact build ensures that it can fit comfortably on any countertop without taking up excessive space.

Another noteworthy characteristic is the appliance’s ease of cleaning. Many components are dishwasher-safe, simplifying the post-cooking cleanup process. The robust construction of the attachments also means they are built to withstand regular use, ensuring that the appliance remains a staple in the kitchen.

Furthermore, this model is often equipped with safety features, such as a locking mechanism, to prevent accidental operation. This is particularly beneficial when handling large quantities of ingredients or when using higher speeds.

In conclusion, the KitchenAid W10246119C combines power, versatility, and ease of use, making it an excellent tool for anyone looking to elevate their culinary skills. With its robust motor, multiple speed options, and range of attachments, it has become a trusted appliance in kitchens around the world, promising consistent results and effortless operation. Whether you are preparing a holiday feast or a simple weeknight dinner, the W10246119C stands ready to assist in creating delicious meals.
Top Page Image Contents