KitchenAid W10246119C Adjust LevelingLegs, Install Anti-TipBracket, Freestanding Ranges

Page 8

Freestanding Ranges:

1.Measure the distance of the countertop to the floor.

2.Then measure from the top of the range cooktop trim to the floor.

A

A. Distance from the top of the range cooktop trim to the floor

3.Your leveling height will be the difference between the 2 measurements you have just taken.

Adjust LevelingLegs

1.If range height adjustment is necessary, use a wrench or pliers to loosen the 4 leveling legs.

This may be done with the range on its back or with the range supported on 2 legs after the range has been placed back to a standing position.

NOTE: To place range back up into a standing position, put a sheet of cardboard or hardboard in front of range. Using 2 or more people, stand range back up onto the cardboard or hardboard.

2.Adjust the leveling legs to the correct height. Leveling legs can be loosened to add up to a maximum of 1" (2.5 cm). A minimum of ³⁄₁₆" (5 mm) is needed to engage the anti-tip bracket.

NOTE: If height adjustment is made when range is standing, tilt the range back to adjust the front legs, then tilt forward to adjust the rear legs.

3.When the range is at the correct height, check that there is adequate clearance under the range for the anti-tip bracket. Before sliding range into its final location, check that the anti- tip bracket will slide under the range and onto the rear leveling leg prior to anti-tip bracket installation.

Install Anti-TipBracket

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.

Failure to follow these instructions can result in death or serious burns to children and adults.

Contact a qualified floor covering installer for the best procedure for drilling mounting holes through your type of floor covering.

Before moving range, slide range onto shipping base, cardboard or hardboard.

1.Remove template from the anti-tip bracket kit (found inside the oven cavity) or from the back page of this manual.

2.Place template on the floor in cabinet opening so that the left edge is against cabinet and top edge is against rear wall, molding or cabinet.

3.Tape template in place.

4.If countertop is not flush with cabinet opening edge, align template with overhang.

If cabinet opening is wider than specified in the “Location Requirements” section, adjust template so range will be centered in cabinet opening.

5.To mount anti-tip bracket to wood floor, drill two ¹⁄₈" (3.2 mm) holes at the positions marked on the bracket template. Remove template from floor.

To mount anti-tip bracket to concrete or ceramic floor, use a ³⁄₁₆" (4.8 mm) masonry drill bit to drill 2 holes at the positions marked on the bracket template. Remove template from floor. Tap plastic anchors into holes with a hammer.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Table of Contents/Table des matières W10246119CRange Safety Table DES MatièresLocation Requirements Installation RequirementsToolsandParts Mobile Home Additional Installation Requirements Product Dimensions Freestanding RangeMobile home installations require Slide-in RangeElectrical Connection Cabinet DimensionsElectrical Requirements U.S.A.Only If connecting to a 4-wire system If connecting to a 3-wire systemLocal codes may permit the use of a UL listed, 3-wire Electrical Requirements -CanadaOnlyInstallation Instructions CountertopPreparation Measurefor Proper HeightUnpack Range Slide-In RangesFreestanding Ranges Adjust LevelingLegsInstall Anti-TipBracket Power Supply Cord Direct WireStyle 1 Power supply cord strain relief Electrical Connection -U.S.A.OnlyTighten strain relief screw against the power supply cord Style 2 Direct wire strain reliefDisconnect or Direct wire Circuit breaker Box Assemble a UL listed strain relief in the openingWire connection Power Supply Cord Hex nut Green ground wire Ground-link screwMetal ground strap Discard Ground-link screw Line 2 red Line 1 blackDirect Wire Installation Copper or Aluminum Wire Wire Connection Direct WireBare green ground wire Hex nutGauge copper Lbs-in .8 N-m Gauge aluminum Lbs-in .0 N-m Bare Wire Torque SpecificationsWire Awg Torque Complete Installation Verify Anti-Tip BracketLocationLevel Range Movingthe RangeFor power supply cord-connected ranges For direct-wired rangesExigences Dinstallation Sécurité DE LA CuisinièreOutillage et pièces Outillage nécessaireExigences demplacement Pièces nécessairesPlanchette de remplissage arrière facultative Lors de l’utilisation d’un cordon d’alimentation électriqueDimensions du produit Cuisinière autoportante Cuisinière coulissanteLargeur min. de louverture 30 76,2 cm Dimensions du placardCuisinière coulissante Instructions Dinstallation Spécifications électriquesPréparationduplandetravail Déballage dela cuisinièreInstallation dela brideantibasculement MesurespourunehauteurappropriéeAjuster les pieds de nivellement Cuisinières coulissantesVérification de lemplacement delabride Antibasculement Fixer le gabarit avec du ruban adhésifSi la cuisinière ne fonctionne pas, contrôler ce qui suit Acheverl’installationRéglage delaplomb de lacuisinière Déplacement delacuisinière Cuisinières alimentées par cordon dalimentation

W10246119C specifications

The KitchenAid W10246119C is a versatile and essential kitchen appliance designed to enhance culinary experiences. This model focuses on providing efficiency and convenience for both amateur cooks and seasoned chefs.

One of its standout features is its powerful motor, which delivers optimum performance across a wide range of tasks. This motor is designed for durability and longevity, ensuring that users can rely on it for years to come. Coupled with a variety of attachments, the W10246119C allows users to tackle everything from mixing and blending to kneading and whipping, making it an invaluable addition to any kitchen.

The appliance typically incorporates several speed settings, allowing for precise control over mixing. This feature is crucial for achieving the perfect texture when preparing ingredients, be it for baking or cooking. Whether you need a slow stir for delicate mixtures or high-speed whipping for cream and egg whites, the W10246119C offers the flexibility required.

Technologically, the KitchenAid W10246119C often includes a user-friendly interface, featuring simple controls that make operation straightforward. The design is elegant, usually available in various colors to complement any kitchen décor. Additionally, its compact build ensures that it can fit comfortably on any countertop without taking up excessive space.

Another noteworthy characteristic is the appliance’s ease of cleaning. Many components are dishwasher-safe, simplifying the post-cooking cleanup process. The robust construction of the attachments also means they are built to withstand regular use, ensuring that the appliance remains a staple in the kitchen.

Furthermore, this model is often equipped with safety features, such as a locking mechanism, to prevent accidental operation. This is particularly beneficial when handling large quantities of ingredients or when using higher speeds.

In conclusion, the KitchenAid W10246119C combines power, versatility, and ease of use, making it an excellent tool for anyone looking to elevate their culinary skills. With its robust motor, multiple speed options, and range of attachments, it has become a trusted appliance in kitchens around the world, promising consistent results and effortless operation. Whether you are preparing a holiday feast or a simple weeknight dinner, the W10246119C stands ready to assist in creating delicious meals.
Top Page Image Contents