KitchenAid W10246119C Installation Requirements, ToolsandParts, Location Requirements

Page 3

INSTALLATION REQUIREMENTS

ToolsandParts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed

Tape measure

Masking tape

Flat-blade screwdriver

¼" nut driver

Level

⁵⁄₁₆" nut driver

Hammer

¹⁄₈" (3.2 mm) drill bit (for

Hand or electric drill

 

wood floors)

 

³⁄₁₆" (4.8 mm) carbide-tipped

Wrench or pliers

 

masonry drill bit (for

 

Marker or pencil

 

 

concrete/ceramic floors)

Parts supplied

Check that all parts are included.

A

B

C

A.Anti-tip bracket

B.Plastic anchors (2)

C.#10 x ¹⁄₂" screws (2)

Anti-tip bracket must be securely mounted to subfloor. Thickness of flooring may require longer screws to anchor bracket to subfloor. Longer screws are available from your local hardware store.

Parts needed

If using a power supply cord:

A UL listed power supply cord kit marked for use with ranges. The cord should be rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with nominal 1³⁄₈" (3.5 cm) diameter connection opening and must end in ring terminals or open-end spade terminals with upturned ends.

A UL listed strain relief.

Check local codes. Check existing electrical supply. See “Electrical Requirements” section.

It is recommended that all electrical connections be made by a licensed, qualified electrical installer.

Rear Filler Strip (optional)

The rear filler strip may be used to fill a gap between the rear of the slide-in cooktop and the wall in a freestanding cutout.

A

B

B

C

A. Rear filler strip

B.Countertop

C.Countertop cutout

Please reference the “Assistance or Service” section of the Use and Care Guide to order.

Black - W10113902A

White - W10113903A

Biscuit - W10113904A

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located inside the oven door on the right-hand side oven door trim.

The range should be located for convenient use in the kitchen.

To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood or microwave range hood combination that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances.

The floor anti-tip bracket must be installed. To install the anti- tip bracket shipped with the range, see “Install Anti-Tip Bracket” section.

Grounded electrical supply is required. See “Electrical Requirements” section.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194°F (90°C).

3

Image 3
Contents W10246119C Table of Contents/Table des matièresTable DES Matières Range SafetyInstallation Requirements ToolsandPartsLocation Requirements Slide-in Range Mobile Home Additional Installation RequirementsProduct Dimensions Freestanding Range Mobile home installations requireCabinet Dimensions Electrical Requirements U.S.A.OnlyElectrical Connection Electrical Requirements -CanadaOnly If connecting to a 4-wire systemIf connecting to a 3-wire system Local codes may permit the use of a UL listed, 3-wireSlide-In Ranges Installation InstructionsCountertopPreparation Measurefor Proper Height Unpack RangeAdjust LevelingLegs Install Anti-TipBracketFreestanding Ranges Electrical Connection -U.S.A.Only Power Supply CordDirect Wire Style 1 Power supply cord strain reliefAssemble a UL listed strain relief in the opening Tighten strain relief screw against the power supply cordStyle 2 Direct wire strain relief Disconnect or Direct wire Circuit breaker BoxLine 2 red Line 1 black Wire connection Power Supply CordHex nut Green ground wire Ground-link screw Metal ground strap Discard Ground-link screwHex nut Direct Wire Installation Copper or Aluminum WireWire Connection Direct Wire Bare green ground wireBare Wire Torque Specifications Wire Awg TorqueGauge copper Lbs-in .8 N-m Gauge aluminum Lbs-in .0 N-m Movingthe Range Complete InstallationVerify Anti-Tip BracketLocation Level RangeFor direct-wired ranges For power supply cord-connected rangesOutillage nécessaire Exigences DinstallationSécurité DE LA Cuisinière Outillage et piècesLors de l’utilisation d’un cordon d’alimentation électrique Exigences demplacementPièces nécessaires Planchette de remplissage arrière facultativeCuisinière coulissante Dimensions du produit Cuisinière autoportanteDimensions du placard Cuisinière coulissanteLargeur min. de louverture 30 76,2 cm Déballage dela cuisinière Instructions DinstallationSpécifications électriques PréparationduplandetravailCuisinières coulissantes Installation dela brideantibasculementMesurespourunehauteurappropriée Ajuster les pieds de nivellementFixer le gabarit avec du ruban adhésif Vérification de lemplacement delabride AntibasculementAcheverl’installation Réglage delaplomb de lacuisinièreSi la cuisinière ne fonctionne pas, contrôler ce qui suit Cuisinières alimentées par cordon dalimentation Déplacement delacuisinière

W10246119C specifications

The KitchenAid W10246119C is a versatile and essential kitchen appliance designed to enhance culinary experiences. This model focuses on providing efficiency and convenience for both amateur cooks and seasoned chefs.

One of its standout features is its powerful motor, which delivers optimum performance across a wide range of tasks. This motor is designed for durability and longevity, ensuring that users can rely on it for years to come. Coupled with a variety of attachments, the W10246119C allows users to tackle everything from mixing and blending to kneading and whipping, making it an invaluable addition to any kitchen.

The appliance typically incorporates several speed settings, allowing for precise control over mixing. This feature is crucial for achieving the perfect texture when preparing ingredients, be it for baking or cooking. Whether you need a slow stir for delicate mixtures or high-speed whipping for cream and egg whites, the W10246119C offers the flexibility required.

Technologically, the KitchenAid W10246119C often includes a user-friendly interface, featuring simple controls that make operation straightforward. The design is elegant, usually available in various colors to complement any kitchen décor. Additionally, its compact build ensures that it can fit comfortably on any countertop without taking up excessive space.

Another noteworthy characteristic is the appliance’s ease of cleaning. Many components are dishwasher-safe, simplifying the post-cooking cleanup process. The robust construction of the attachments also means they are built to withstand regular use, ensuring that the appliance remains a staple in the kitchen.

Furthermore, this model is often equipped with safety features, such as a locking mechanism, to prevent accidental operation. This is particularly beneficial when handling large quantities of ingredients or when using higher speeds.

In conclusion, the KitchenAid W10246119C combines power, versatility, and ease of use, making it an excellent tool for anyone looking to elevate their culinary skills. With its robust motor, multiple speed options, and range of attachments, it has become a trusted appliance in kitchens around the world, promising consistent results and effortless operation. Whether you are preparing a holiday feast or a simple weeknight dinner, the W10246119C stands ready to assist in creating delicious meals.