KitchenAid 2313684A manual Leveling, ConnectWater Supply, Tools needed, Connecting the water line

Page 5

Leveling

It is important for the ice maker to be level in order to work properly. Depending upon where you install the ice maker, you may need to make several adjustments to level it. You may also use the leveling legs to lower the height of the ice maker for undercounter installations.

Tools needed:

Gather the required tools and parts before starting installation.

■9" level

■Adjustable wrench

NOTE: It is easier to adjust the leveling legs if you have another person to assist you.

1.Move the ice maker to its final location.

NOTE: If this is a built-in installation, move the ice maker as close as possible to the final location.

2.Place a carpenter’s level on top of the product to see if the ice maker is level from front to back and side to side.

3.Push up on the top front of the ice maker, and then locate the leveling screws that are on the bottom front of the ice maker.

4.Using an adjustable wrench, change the height of the legs as follows:

■Turn the leveling leg to the right to lower that side of the ice maker.

■Turn the leveling leg to the left to raise that side of the ice maker.

NOTE: The ice maker should not wobble. Use shims to add stability when needed.

5.Push up on the top rear of the ice maker and locate the leveling legs that are on the bottom rear of the ice maker.

6.Follow the instructions in Step 4 to change the height of the legs.

7.Use a carpenter’s level to recheck the ice maker to see that it is even from front to back and side to side. If the ice maker is not level, repeat steps 2 to 5. If the ice maker is level, go to the “Connect Water Supply” section.

■¹⁄₄" nut driver

■¹⁄₄" drill bit

■Hand drill or electric drill properly grounded

NOTE: Your ice maker dealer has a kit available with a ¹⁄₄"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or ³⁄₁₆"

(4.76 mm) saddle valve which reduces water flow and clogs more easily.

Connecting the water line

1.Turn off main water supply. Turn on nearest faucet long enough to clear line of water.

2.Find a ¹⁄₂" (12.70 mm) to 1¹⁄₄" (3.18 cm) vertical cold water pipe near the ice maker.

NOTE: Horizontal pipe will work, but the following procedure

must be followed: Drill on the top side of the pipe, not the bottom. This will help keep water away from the drill. This also keeps normal sediment from collecting in the valve.

3.Using a grounded drill, drill a ¹⁄₄" (6.35 mm) hole in the cold water pipe you have selected.

4.Fasten shutoff valve to cold water pipe with pipe clamp. Be sure outlet end is solidly in the ¹⁄₄" (6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten packing nut. Tighten the pipe clamp screws carefully and evenly so washer makes a watertight seal. Do not overtighten the pipe clamp or you may crush cold water pipe if it is soft copper tubing. Do not use a piercing-type or ³⁄₁₆" (4.76 mm) saddle-type valve which reduces water flow and clogs more easily.

5.Now you are ready to connect the copper tubing. Use ¹⁄₄" (6.35 mm) OD soft copper tubing for the cold water supply.

■Ensure that you have the proper length needed for the job. Be sure both ends of the copper tubing are cut square.

■Slip compression sleeve and compression nut on copper tubing as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

A

H B

C

ConnectWater Supply

G F E

D

Read all directions thoroughly before you begin.

IMPORTANT:

■Plumbing shall be installed in accordance with the International Plumbing Code and any local codes and ordinances.

■Use copper tubing and check for leaks.

■Install copper tubing only in areas where temperatures will remain above freezing.

Tools needed:

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

■Flat-blade screwdriver

■⁷⁄₁₆" and ¹⁄₂" open-end wrenches or two adjustable wrenches

A. Cold water pipe

E. Compression nut

B. Pipe clamp

F. Compression sleeve

C. Copper tubing

G. Shutoff valve

D. Coupling (purchased)

H. Packing nut

6.Place the free end of the tubing into a container or sink, and turn on main water supply and flush out tubing until water is clear. Turn off shutoff valve on the water pipe.

NOTE: Always drain the water line before making the final connection to the inlet of the water valve to avoid possible water valve malfunction.

7.Bend the copper tubing to meet the water line inlet which is located on the back of the ice maker cabinet as shown. Leave a coil of copper tubing to allow the ice maker to be pulled out of the cabinet or away from the wall for service.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents ICE Maker Table of Contents/Table des matièresTable DES Matières Table of ContentsInstallation Instructions ICE Maker SafetyCleaning Before Use Unpack the Ice MakerElectrical Requirements Location RequirementsWater Supply Requirements Recommended grounding methodLeveling Connecting the water lineConnectWater Supply Tools neededDrain Connection Connecting the DrainDrain Pump System on some models Gravity Drain SystemIce Maker Door Normal Sounds ICE Maker USEHow Your Ice Maker Works Reverse Door CatchICE Maker Care Usingthe ControlsCleaning Dirty or clogged condenser CondenserInterior Components To shut down the ice maker Vacation and MovingCareIce Production TroubleshootingIce Maker Operation Plumbing Problems Assistance or ServiceIce Quality U.S.AONE Year Limited Warranty Kitchenaid ICE Maker WarrantyItems Kitchenaid will not PAY for Disclaimer of Implied Warranties Limitation of RemediesSécurité DE LA Machine À Glaçons Instructions D’INSTALLATIONDéballage de la machine à glaçons Enlèvement des matériaux d’emballageMéthode de mise à la terre recommandée Exigences demplacementSpécificationsélectriques Spécifications de l’alimentation en eauRaccordement à lacanalisation d’eau NivellementOutillage nécessaire Outils requisVUE Arrière Raccordementau conduit dévacuationVidange par gravité Système avec pompe de vidange sur certains modèles Porte de la machine à glaçonsRaccordement du conduit dévacuation Dépose de la porteSons normaux Réinstallation de la porteInversion des charnières Inversion du loquet de porte Charnière supérieureHoliday Mode mode vacances Utilisation des commandesUtilisation DE LA Machine À Glaçons Fonctionnement dela machine à glaçonsNettoyage Entretien DE LA Machine À GlaçonsVis de serrage Support de pelle à glace Composants intérieursArrêt de la machine à glaçons Précautions à prendre avant lesvacances Ou déménagementProduction deglaçons DépannageLa machine à glaçons ne fonctionne pas La machine à glaçons semble bruyanteProblèmes deplomberie Assistance OU ServiceQualité des glaçons Kitchenaid NE Prendra PAS EN Charge Garantie DE LA Machine À Glaçons KitchenaidGarantie Limitée DE UN AN All rights reserved 2313684A

2313684A specifications

The KitchenAid 2313684A is a versatile and powerful addition to any kitchen, designed to cater to the needs of home cooks and professional chefs alike. This model stands out with its exceptional design and array of features that enhance the cooking experience.

One of the main highlights of the KitchenAid 2313684A is its robust construction. Built to last, it combines a stainless steel body with a powerful motor that ensures durability and resilience. The elegant design not only makes it aesthetically pleasing but also easy to clean, maintaining its polished look after numerous culinary adventures.

The 2313684A is equipped with a variety of attachments, enabling users to perform multiple functions in the kitchen. From mixing and kneading to whipping and pounding, this device eliminates the need for various gadgets, as it can handle a range of tasks with ease. This feature is especially useful for those who wish to streamline their kitchen tools without sacrificing functionality.

Another significant feature is the variable speed control. Users can choose from multiple speeds, allowing for precise mixing according to individual recipes and preferences. This flexibility is essential when dealing with different ingredients, ensuring perfect results whether making delicate meringues or robust bread doughs.

The KitchenAid 2313684A also embraces modern technology with its ergonomic design, which provides a comfortable grip and usability. The bowl-lift mechanism allows for easy access to ingredients and the ability to work with larger batches, making it a practical choice for larger households or those who like to entertain.

Safety is integral to KitchenAid's philosophy, and the 2313684A incorporates various safety measures, including a locking mechanism during operation. This feature provides peace of mind, allowing users to focus on their culinary creations without worrying about accidental mishaps.

Moreover, KitchenAid offers a range of color options for the 2313684A, allowing customers to choose a model that matches their kitchen decor and personal style. This attention to detail ensures that the appliance not only performs well but also complements the overall aesthetic of the kitchen.

In conclusion, the KitchenAid 2313684A combines power, versatility, and style, making it an indispensable tool for any cooking enthusiast. Its high-quality construction, numerous attachments, variable speed options, and safety features set it apart in the competitive market of kitchen appliances, ensuring that it meets the demands of both casual cooks and seasoned professionals. Whether you’re baking a cake, whipping cream, or kneading dough, the KitchenAid 2313684A is designed to make the process efficient and enjoyable.
Top Page Image Contents