KitchenAid W10300928B Problem Solution Will not Fill, Water Remains, TUB/WILL not Drain, Odors

PROBLEM	SOLUTION
WILL NOT FILL	Be sure the water is turned on to the dishwasher.
	Check that the float is free from obstructions. (See “Parts and Features.”)
	Check for suds in the dishwasher. If foam or suds are detected, the dishwasher may not operate
	properly or may not fill with water. (See “BLINKING LIGHTS” in “Troubleshooting.”)
WATER REMAINS IN THE	Be sure the cycle has completed (the Clean light is on). If it has not, you will need to resume the
TUB/WILL NOT DRAIN	cycle by closing the door and pressing START/RESUME.
	If dishwasher is connected to a food waste disposer, be sure the knockout plug has been removed
	from the disposer inlet.
	Check for kinks in the drain hose.
	Check for food obstructions in the drain or disposer.
	Check your house fuse or circuit breaker.
HARD WATER	NOTE: Extremely hard water mineral deposits can cause damage to your dishwasher and make it
(WHITE RESIDUE ON	difficult to achieve good cleaning. A water softener is strongly recommended if your hardness is
DISHWASHER INTERIOR OR	15 grains or more. If a water softener is not installed, the following steps may help:
GLASSWARE)	Use a commercial cleaner designed for dishwashers once per month.
	Always use a rinse aid.
	Always use a high-quality, fresh detergent.
	Use a detergent booster/water softener additive designed for dishwashers.
ODORS	NOTE: If the dishwasher is not used daily, you can run a rinse cycle with the partial load daily until
	a full load is ready to run, or use the Top Rack Only option (on some models) for partial loads.
	Run a vinegar rinse through the dishwasher by putting 2 cups (500 mL) of white vinegar in an
	upright glass measuring cup in the lower rack. Run a normal cycle with the Heat Dry option turned
	off. Do not use detergent.
	The dishwasher may not be draining properly, see “WATER REMAINS IN THE TUB/WILL NOT
	DRAIN” in “Troubleshooting.”
NOISY	NOTES:
	■ Surging sounds can occur periodically throughout the cycle while the dishwasher is draining.
	■ Normal water valve hissing may be heard periodically.
	■ A normal snap sound may be heard when the detergent dispenser opens during the cycle and
	when the door is opened at the end of the cycle.
	■ Improper installation will affect noise levels.
	A thumping sound may be heard if items extend beyond the racks and interfere with the wash
	arms. Readjust the dishware and resume the cycle.
FOOD SOILS REMAIN	Be sure the dishwasher is loaded correctly. Improper loading can greatly decrease the washing
ON DISHES	performance (see Dishwasher Use”).
	Select the proper cycle and option for the type of soils. The Heavy Duty cycle with the ProScrub®
	(on some models) option can be used for tougher loads.
	Be sure the incoming water temperature is at least 120°F (49ºC).
	Use the proper amount of fresh detergent. More detergent is needed for heavier-soiled loads and
	hard water conditions.
	Scrape food from dishes prior to loading (do not prerinse).
DISHES DIRTY/SUDS IN	If foam or suds are detected by the dishwasher sensing system, the dishwasher may not operate
DISHWASHER/CYCLE NOT	properly or may not fill with water.
COMPLETE	Suds can come from:
	■ Using the incorrect type of detergent, such as dish detergent for hand washing dishes, laundry
	detergent, or hand soap.
	■ Not replacing the rinse aid dispenser cap after filling (or refilling) the rinse aid.
	■ Using an excessive amount of dishwasher detergent.
	Call for service.
	If no water was present in the machine at any time during a heated wash cycle, the cycle will end
	and the Clean LED will not come on. See “Will Not Fill” in “Troubleshooting.”
DID NOT SANITIZE	If the sanitized light is blinking, the load is NOT sanitized. The cycle was interrupted in the final
	rinse, or the temperature for your water heater is set too low. Set your water heater to 120ºF (49ºC).
DAMAGE TO DISHWARE	Improper loading can cause dishes to become chipped or damaged. (See specific loading
	instructions within this guide.)
BLINKING LIGHTS	Blinking LED's will occur when the cycle is paused or when the cycle has been interrupted by
	opening the door. In this case, the Start/Resume button LED, the Cycle Status Indicator LED(s),
	and the countdown bars on the Cycle Status Display all blink together to indicate that attention is
	needed. See Start or Resume a Cycle in the “Dishwasher Use” section.
	Blinking LED's can also occur when certain errors have been detected. In this case,the Clean/
	Complete LED will blink one time with a pause in between blinks.
	Call for service.

14