KitchenAid W10275503B installation instructions Install Custom Panel Option

Page 15

Custom panel dimensions - Dishwashers with control panel on the front

(65.8 cm)

(19.1 mm)

(3.2 mm)

*This dimension is for 4" (10.2 cm) toe kick. If the installation needs a higher toe kick, adjust the height of the wood panel accordingly. Not recommended for toe kicks greater than 6" (15.2 cm).

Follow directions in Option 2 of “Install custom panel” section.

Install Custom Panel – Option 1

(Models KUDS40FVPA, KUDS50FVPA, KUDE60FVPA, and KUDE70FVPA)

NOTE: The handle for the custom panel is not included.

IMPORTANT: If the handle is attached from the back of the custom panel, the screw holes should be countersunk for the screws heads to be flush with the panel. If the handle is attached to the front of the custom panel, the screw lengths cannot exceed the panel thickness. For more information on KitchenAid custom handle selection, refer to the KitchenAid Catalog, visit www.kitchenaid.com, or call 1-800-422-1230.

NOTE: A customer-supplied full-front panel must weigh no more than 16 lbs (7.3 kg) and must be made to specific dimensions. It is recommended that a cabinetmaker cut the custom panel because of the precise dimensions needed.

NOTE: All mounting hardware supplied is for a ³⁄₄"

(19.1 mm) thick wood panel. If a thinner wood panel, or materials other than wood are used, it is the consumer’s responsibility to obtain the proper length screws and adjust the pilot holes accordingly.

IMPORTANT: Use a moisture-resistant sealer on both sides and all edges of the panel to avoid damage from humidity.

1 Custom panel installation - Dishwashers with control panel on the top

23¹⁄₂"

 

 

*30³⁄₁₆" (76.7 cm)

(59.7 cm)

 

 

 

³⁄₄" (19.1 mm)

*This dimension is for 4" (10.2 cm) toe kick. If the installation needs a higher toe kick, adjust the height of the wood panel accordingly. Not recommended for toe kicks greater than 6" (15.2 cm).

With a TORX® screwdriver, remove three screws from both sides, as shown; hold the outer panel up while removing the screws. Save screws for reinstallation.

2 Custom panel dimensions— Dishwashers with control panel on the top

3 screws per side

outer panel

Gently set outer panel aside. Lay the customer-supplied custom panel face down on a covered, non-scratching surface.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents W10275503B You Need to Table of ContentsTools and Parts Location Requirements Insulation may be compressed Not used on all models Product and Cabinet Opening DimensionsUse of air gap Drain RequirementsWater Supply Requirements Electrical RequirementsPrepare Cabinet Opening-New Utilities Prepare Cabinet Opening-Existing UtilitiesPrepare and Route Water Line Add 90 elbow fitting to the water supply line Route water supply lineFlush water supply line Slide nut and ferrule onto tubingWaste disposer no air gap Install Drain HoseRoute drain hose Connect drain hosePrepare Dishwasher Install Moisture Barrier under a wood countertopRemove terminal box cover Make Power Supply Cord ConnectionPower Cord-Route cord into terminal box Remove panelsDetermine Cabinet Opening Custom Panel Dimensions Install the Door Handle on some modelsModels KUDS40FVPA, KUDS50FVPA, KUDE60FVPA, and KUDE70FVPA Install Custom Panel OptionAttach body panel Install custom panelMark line Mark pilot holesModels KUDC03IV and KUDS30IV Choose Attachment OptionMove Dishwasher into Cabinet Opening Check water and drain hose position Closes too quickly- Decrease spring tensionDoor falls open- Increase spring tension Connect to Water Supply Connect to Drain Make Direct Wire Electrical ConnectionSlide clamp onto connector Direct Wire-Route cable into terminal boxDirect Wire-Reinstall terminal box cover Direct Wire-Connect ground wireDirect Wire-Connect remaining wires Direct Wire-Secure cable in strain reliefSecure Dishwasher in Cabinet Opening Check side attachment Bottom Sound Pad Installation on some modelsComplete Installation Reinstall access panelsCheck lower panel edge Power supply cord-Plug into a grounded 3 prong outletReconnect power Reconnect PowerCheck Operation If Dishwasher Does Not OperateAdditional Tips Il faut Table des matièresOutillage et pièces Exigences demplacement 60,6 Dimensions Produit et cavité d’encastrementUtilisation du dispositif de brise-siphon Exigences dévacuationSpécifications de l’alimentation en eau Spécifications électriquesQuel type de connexion lutilisateur emploie-t-il? Déconnecter la source de courant électriqueFermeture de lalimentation en eau Lutilisateur possède-t-il déjà des moyens de raccordement?Raccordement direct Préparation du trou Préparation et acheminement de la canalisation d’eauCordon dalimentation électrique Préparation du trou Perçage du trouAcheminement de la canalisation dalimentation en eau Vidange de la canalisation dalimentation en eauEnfiler l’écrou et la virole sur la canalisation Pas de broyeur à déchets sans brise-siphon Installation du tuyau d’évacuationAcheminement du tuyau dévacuation Broyeur à déchets sans brise-siphonOption D pas de broyeur à déchets avec brise-siphon Broyeur à déchets avec brise-siphonPas de broyeur à déchets avec brise-siphon Option C broyeur à déchets avec brise-siphonDépose des panneaux Installation dun serre-câblePréparation du lave-vaisselle Placer le lave-vaisselle sur le dosCordon d’alimentation Conducteur de liaison à la terre Raccordement du cordon dalimentationTableau de réglage Hauteur du lave-vaisselle Configuration du câblageÉvaluation de l’ouverture dencastrement du placard Mesure de louverture dencastrement du placardPlanchers surélevés Ajouter des cales si nécessaire Installation de la poignée de porte sur certains modèlesDimensions du panneau personnalisé Installation de la poignée de porteModèles KUDS40FVPA, KUDS50FVPA, KUDE60FVPA, et KUDE70FVPA Installation du panneau personnalisé OptionMarquage de laxe Marquage des avant-trousModèles KUDC031V et KUDS301V Installation du panneau personnaliséFixation de la poignée Fixation du panneau principalOption 1, Fixation au plan de travail Choix de l’option de fixationSortir le bride Insérer la brideOption 2, Fixation au côté du lave-vaisselle Sectionnement de lextrémité de la brideInsertion des boutons en plastique Mise en position verticale du lave-vaisselleInsertion du lave-vaisselle dans louverture du placard Ouverture et fermeture de la porteRaccorder le raccord coudé de 90 à la valve Méthode recommandée Méthode facultativeRaccordement à l’alimentation en eau Vérification de laplomb et réglage des pieds si nécessaireEnfilement de la bride sur le raccord Raccordement au circuit dévacuationRaccordement électrique direct Position définitive de la bride de tuyauRaccordement direct Raccordement du fil de mise à la terre Raccordement direct Raccordement des fils restantsRaccordement direct Fixation du câble dans le serre-câble Fixation du lave-vaisselle Vérification de la distance de dégagement pour la porteVérification de lespacement Lintérieur Achever linstallation Réinstallation des panneaux daccèsVérification de la fixation latérale Rétablir la source de courant électrique Inspection de la rive de panneau inférieureSerrage des vis Reconnexion de la source de courant électriqueContrôle du fonctionnement Si le lave-vaisselle ne fonctionne pasConseils supplémentaires Page Page Page All rights reserved

W10275503B specifications

The KitchenAid W10275503B is a high-performance replacement water filter designed for KitchenAid refrigerators. This advanced filtration system ensures that your drinking water and ice are clean, fresh, and free from impurities.

One of the standout features of the W10275503B is its ability to reduce contaminants commonly found in tap water. This includes chlorine taste and odor, lead, mercury, and various other harmful substances. By utilizing activated carbon and advanced filtration technologies, this water filter significantly improves the taste and quality of your water, providing peace of mind for you and your family.

The W10275503B employs a simple push-button installation process, making it easy for homeowners to replace their filters without professional assistance. This user-friendly feature enhances the overall convenience, ensuring that your water filter replacement is hassle-free. Additionally, the filter is designed to be compatible with a wide range of KitchenAid refrigerator models, ensuring that you can find the right fit for your appliance.

Another impressive feature is the filter's longevity. The W10275503B can filter up to 200 gallons of water, depending on your water quality, before it needs to be replaced. This longevity reduces the frequency of replacements, saving you both time and money over the long run. The filter indicator light on compatible refrigerators also alerts you when it's time for a change, further simplifying the upkeep of your kitchen appliance.

The design of the W10275503B emphasizes efficiency and sustainability. Made with eco-friendly materials, the filter contributes to a reduced environmental footprint. KitchenAid's commitment to quality is evident in their rigorous testing and certification for NSF/ANSI standards, ensuring that the water filter meets strict safety and performance criteria.

In summary, the KitchenAid W10275503B is an essential accessory for KitchenAid refrigerator owners who value clean, great-tasting water. Its advanced filtration technology, ease of installation, and impressive lifespan make it a top choice. By investing in this replacement water filter, you enhance the quality of your drinking water and ice, all while enjoying the reliability that KitchenAid is known for.
Top Page Image Contents