KitchenAid W10275503B Choose Attachment Option, Models KUDC03IV and KUDS30IV

Page 17

Install Custom Panel – Option 2

(Models KUDC03IV and KUDS30IV)

All models require an accessory option to attach custom panels. Kit Number 8171555 (black), 8171556 (white) or 8171557 (biscuit) are available. To order, call customer service at 1-800-444-1230.

NOTE: A custom full-front panel must weigh no more than 14 lbs (6.3 kg) and must be made to specific dimensions. It is recommended that a cabinetmaker cut the custom panel because of the precise dimensions needed.

IMPORTANT: Use a moisture-resistant sealer on both sides and all edges of the panel to avoid damage from humidity.

NOTE: These dimensions are for frameless custom panel models with a 4" (10.2 cm) console only.

1 Custom panel installation - Dishwashers with control panel on the front

23³⁄₈"

 

 

*25²⁹⁄₃₂" (65.8 cm)

(65.8 cm)

 

 

 

³⁄₄"

 

(19.1 mm)

¹⁄₈" (3.2 mm)

 

¹⁄₈"

(3.2 mm)

*This dimension is for 4" (10.2 cm) toe kick. If the installation needs a higher toe kick, adjust the height of the wood panel accordingly. Not recommended for toe kicks greater than 6" (15.2 cm).

With a TORX® screwdriver, remove three screws from both sides, as shown; hold the outer panel up while removing the screws. Save screws for reinstallation.

2 Custom panel dimensions— Dishwashers with control panel on the front

3 screws per side

outer panel

Gently set outer panel aside. Lay the cutomer-supplied custom panel face down on a non-scratching surface. Position the outer panel on the back of the customer-supplied custom panel as shown; make sure top edge of the outer panel is aligned with the top edge of the customer-supplied custom panel, and both panels are centered side to side.

3 Mark pilot holes

Mark pilot

holes

Mark all four hole locations; remove outer panel and drill ³⁄₃₂" pilot holes ¹⁄₂" (13 mm) deep, in customer-supplied custom panel. Place the outer panel on the back of the customer-supplied custom panel and align holes. Attach outer panel to back of customer-supplied custom panel with four #10 x ¹⁄₂" wood screws (not supplied). If the customer-supplied custom panel is less than ³⁄₄" (1.9 cm) thick where the screws are attached, shorter screws may be required.

4 Attach body panel

 

Align top

Reinstall

edges

 

3 screws

 

each side

Customer-supplied

 

panel

Attach the panel assembly to the door by reinstalling the three screws on each side.

Choose Attachment Option

Excessive Weight Hazard

Use two or more people to move and install dishwasher.

Failure to do so can result in back or other injury.

Using 2 or more people, stand the dishwasher up.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents W10275503B You Need to Table of ContentsTools and Parts Location Requirements Insulation may be compressed Not used on all models Product and Cabinet Opening DimensionsWater Supply Requirements Drain RequirementsElectrical Requirements Use of air gapPrepare Cabinet Opening-New Utilities Prepare Cabinet Opening-Existing UtilitiesPrepare and Route Water Line Flush water supply line Route water supply lineSlide nut and ferrule onto tubing Add 90 elbow fitting to the water supply lineRoute drain hose Install Drain HoseConnect drain hose Waste disposer no air gapPrepare Dishwasher Install Moisture Barrier under a wood countertopPower Cord-Route cord into terminal box Make Power Supply Cord ConnectionRemove panels Remove terminal box coverDetermine Cabinet Opening Custom Panel Dimensions Install the Door Handle on some modelsModels KUDS40FVPA, KUDS50FVPA, KUDE60FVPA, and KUDE70FVPA Install Custom Panel OptionMark line Install custom panelMark pilot holes Attach body panelModels KUDC03IV and KUDS30IV Choose Attachment OptionMove Dishwasher into Cabinet Opening Door falls open- Increase spring tension Check water and drain hose positionCloses too quickly- Decrease spring tension Connect to Water Supply Slide clamp onto connector Make Direct Wire Electrical ConnectionDirect Wire-Route cable into terminal box Connect to DrainDirect Wire-Connect remaining wires Direct Wire-Connect ground wireDirect Wire-Secure cable in strain relief Direct Wire-Reinstall terminal box coverSecure Dishwasher in Cabinet Opening Complete Installation Bottom Sound Pad Installation on some modelsReinstall access panels Check side attachmentReconnect power Power supply cord-Plug into a grounded 3 prong outletReconnect Power Check lower panel edgeAdditional Tips Check OperationIf Dishwasher Does Not Operate Il faut Table des matièresOutillage et pièces Exigences demplacement 60,6 Dimensions Produit et cavité d’encastrementSpécifications de l’alimentation en eau Exigences dévacuationSpécifications électriques Utilisation du dispositif de brise-siphonFermeture de lalimentation en eau Déconnecter la source de courant électriqueLutilisateur possède-t-il déjà des moyens de raccordement? Quel type de connexion lutilisateur emploie-t-il?Cordon dalimentation électrique Préparation du trou Préparation et acheminement de la canalisation d’eauPerçage du trou Raccordement direct Préparation du trouEnfiler l’écrou et la virole sur la canalisation Acheminement de la canalisation dalimentation en eauVidange de la canalisation dalimentation en eau Acheminement du tuyau dévacuation Installation du tuyau d’évacuationBroyeur à déchets sans brise-siphon Pas de broyeur à déchets sans brise-siphonPas de broyeur à déchets avec brise-siphon Broyeur à déchets avec brise-siphonOption C broyeur à déchets avec brise-siphon Option D pas de broyeur à déchets avec brise-siphonPréparation du lave-vaisselle Installation dun serre-câblePlacer le lave-vaisselle sur le dos Dépose des panneauxCordon d’alimentation Conducteur de liaison à la terre Raccordement du cordon dalimentationÉvaluation de l’ouverture dencastrement du placard Configuration du câblageMesure de louverture dencastrement du placard Tableau de réglage Hauteur du lave-vaisselleDimensions du panneau personnalisé Installation de la poignée de porte sur certains modèlesInstallation de la poignée de porte Planchers surélevés Ajouter des cales si nécessaireMarquage de laxe Installation du panneau personnalisé OptionMarquage des avant-trous Modèles KUDS40FVPA, KUDS50FVPA, KUDE60FVPA, et KUDE70FVPAFixation de la poignée Installation du panneau personnaliséFixation du panneau principal Modèles KUDC031V et KUDS301VSortir le bride Choix de l’option de fixationInsérer la bride Option 1, Fixation au plan de travailInsertion des boutons en plastique Sectionnement de lextrémité de la brideMise en position verticale du lave-vaisselle Option 2, Fixation au côté du lave-vaisselleInsertion du lave-vaisselle dans louverture du placard Ouverture et fermeture de la porteRaccordement à l’alimentation en eau Méthode recommandée Méthode facultativeVérification de laplomb et réglage des pieds si nécessaire Raccorder le raccord coudé de 90 à la valveRaccordement électrique direct Raccordement au circuit dévacuationPosition définitive de la bride de tuyau Enfilement de la bride sur le raccordRaccordement direct Fixation du câble dans le serre-câble Raccordement direct Raccordement du fil de mise à la terreRaccordement direct Raccordement des fils restants Vérification de lespacement Lintérieur Fixation du lave-vaisselleVérification de la distance de dégagement pour la porte Vérification de la fixation latérale Achever linstallationRéinstallation des panneaux daccès Serrage des vis Inspection de la rive de panneau inférieureReconnexion de la source de courant électrique Rétablir la source de courant électriqueConseils supplémentaires Contrôle du fonctionnementSi le lave-vaisselle ne fonctionne pas Page Page Page All rights reserved

W10275503B specifications

The KitchenAid W10275503B is a high-performance replacement water filter designed for KitchenAid refrigerators. This advanced filtration system ensures that your drinking water and ice are clean, fresh, and free from impurities.

One of the standout features of the W10275503B is its ability to reduce contaminants commonly found in tap water. This includes chlorine taste and odor, lead, mercury, and various other harmful substances. By utilizing activated carbon and advanced filtration technologies, this water filter significantly improves the taste and quality of your water, providing peace of mind for you and your family.

The W10275503B employs a simple push-button installation process, making it easy for homeowners to replace their filters without professional assistance. This user-friendly feature enhances the overall convenience, ensuring that your water filter replacement is hassle-free. Additionally, the filter is designed to be compatible with a wide range of KitchenAid refrigerator models, ensuring that you can find the right fit for your appliance.

Another impressive feature is the filter's longevity. The W10275503B can filter up to 200 gallons of water, depending on your water quality, before it needs to be replaced. This longevity reduces the frequency of replacements, saving you both time and money over the long run. The filter indicator light on compatible refrigerators also alerts you when it's time for a change, further simplifying the upkeep of your kitchen appliance.

The design of the W10275503B emphasizes efficiency and sustainability. Made with eco-friendly materials, the filter contributes to a reduced environmental footprint. KitchenAid's commitment to quality is evident in their rigorous testing and certification for NSF/ANSI standards, ensuring that the water filter meets strict safety and performance criteria.

In summary, the KitchenAid W10275503B is an essential accessory for KitchenAid refrigerator owners who value clean, great-tasting water. Its advanced filtration technology, ease of installation, and impressive lifespan make it a top choice. By investing in this replacement water filter, you enhance the quality of your drinking water and ice, all while enjoying the reliability that KitchenAid is known for.
Top Page Image Contents