Hotpoint 50cm Gas Cooker, HAGL 51 P, HAGL 51 K Positioning, Installation of the cooker

Installation

The appliance must only be installed by a competent person. In the UK, CORGI registered installers undertake to work to safe and satisfactory standards. Before moving your cooker check that it is cool, and switch off at the cooker control unit. Movement of your cooker is most easily achieved by lifting the front as follows:

Open the grill door sufficiently to allow a comfortable grip on the underside front edge of the oven roof, avoiding any grill elements.

Note: Take care in moving the cooker as it is heavy. Take care to ensure that any floor covering is not damaged. (FIG. C)

Splashplate optional, apply to Parts Department (see Back Cover for contact number.)

The following instructions should be read by a qualified technician to ensure that the appliance is installed, regulated and technically serviced correctly in compliance with current regulations.

Important: remember to unplug the appliance from the mains before regulating the appliance or carrying out any maintenance work.

Positioning

Important: this unit may be installed and used only in permanently ventilated rooms according to the British Standards Codes Of Practice: B.S. 6172/B.S. 5440, Par. 2 and B.S. 6891 Current Editions. The following requirements must be observed:

a) The cooker should not be installed in a bed sitting

room with a volume of less than 20m3. If it is installed

in a room of volume less than 5m3 an air vent of

effective area of 110cm2 is required, if it is installed

in a room of volume between 5m3 and 10m3 a

supplementary airvent area of 50cm2 is required,

3

Installation of the cooker

GB

For a correct installation of the cooker the following precautions must be followed:

The height of the cooker can be adjusted by means of adjustable feet in the plinth (900mm - 915mm). Adjust the feet by tilting the cooker from the side. Then install the product into position.

NOTE: This appliance must not be fitted on a platform. The cooker is designed to fit between kitchen cabinets spaced 500mm apart. The space either side need only be sufficient to allow withdrawal of the cooker for servicing. It can be used with cabinets one side or both as well as in a corner setting. It can also be used free-standing.

Adjacent side walls which project above hob level, must not be nearer to the cooker than 150mm or 65mm (Fig. A) and should be protected by heat resistant material. Any overhanging surface or cooker hood should not be nearer than 750mm. (Fig.A)

a)The cooker may be located in a kitchen, a kitonen/ diner or bed sitting room, but not in a bathroom or shower room.

b)The hoods must be installed according to the requirements in the hood handbook.

c)The wall in contact with the back of the cooker must be of flameproof material.

d)The cooker is fitted with a safety chain that must be attached to a hook, secured to the wall behind the appliance.

Note: some models can have their gas connection inverted. It is important to make sure the safety chain is always situated on the side which corresponds to the hose holder (Fig. B).

if the volume exceeds 11m no airvent is required.

However, if the room has a door or a window which

opens directly to the outside no air vent is required

even when the volume is between 5m3 and 11m3.

b) During prolonged use of the appliance you may

consider it necessary to open a window to the

outside to improve ventilation.

c) If there are other fuel burning appliances in the

same room, B.S.5440 Part 2 Current Edition, should,

be consulted to determine the requisite air vent

requirements.

Tall cupboard on the right hand side of 50cm gas cooker

65 mm min	min
400 mm min	750 mm	150 mm min

500 mm min

Fig. A

Tall cupboard on the left hand side of 50cm gas cooker

	min	65 mm min
65 mm min	750 mm	400 mm min

500 mm min

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

5