Whirlpool W10240582A Location Requirements, Parts needed, For Mobile Home Installations

Page 4

Parts needed

For direct wire installation

UL listed or CSA approved ¹⁄₂" (12.5 mm) strain relief

2 - 75-watt max incandescent light bulbs or

1 - 75-watt max and 1 - 25-watt max incandescent light bulb (for use as a night light)

Power supply cable (if needed, for direct wire installation)

For power supply cord installation

UL Listed Power Supply Cord Connection Kit marked for range hood use.

2 - 75-watt max incandescent light bulbs or

1 - 75-watt max and 1 - 25-watt max incandescent light bulb (for use as a night light)

For vented installations you also need:

3¹⁄₄" x 10" (8.3 x 25.4 cm) or 6" (15.2 cm) or larger round metal venting

6" (15.2 cm) or larger round damper, if using 6" (15.2 cm) or larger round vent system

3¹⁄₄" x 10" (8.3 x 25.4 cm) to 6" (15.2 cm) or larger diameter transition piece

For cabinets with recessed bottoms:

Two 2" (5.1 cm) wide filler strips. Length and thickness determined by recess dimensions.

Four flat head wood screws or machine screws with washers and nuts (to attach filler strips).

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located inside the range hood on the left wall.

Range hood location should be away from strong draft areas, such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance. Consult the cooktop/range manufacturer installation instructions before making any cutouts.

Grounded electrical outlet is required. See “Electrical Requirements” section.

The hood is factory-set for vented installations. For non- vented (recirculating) installations, charcoal filter pad Part Number 4396390 is available. See the “Assistance or Service” section for information on ordering.

All openings in ceiling and wall where range hood will be installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local codes.

Product Dimensions

 

1¹⁄₂"

12"

(3.8 cm)

1"

(30.5 cm) 9"

(2.5 cm)

(22.9 cm)

 

 

2"

 

(5.1 cm)

9"

(22.9 cm)

³⁄₄"

1¹⁄₂"

(1.9 cm)

(3.8 cm)

 

³⁄₈"

(9.5 mm)

7¹⁄₂"

(19.1 cm)

29 ⁷⁄₈" (75.9 cm) - 30" (76.2 cm) model

20"

35 ⁷⁄₈" (91.1 cm) - 36" (91.4 cm) model

(44.5 cm)

 

Installation Clearances

30" (76.2 cm) or 36" (91.4 cm) min. cabinet opening width

24" (61.0 cm) min.

30" (76.2 cm)

suggested max. bottom of cabinet to cooking surface

13" (33.0 cm) cabinet depth

18" (45.7 cm) min. clearance upper cabinet to countertop

36" (91.4 cm) base cabinet height

4

Image 4
Contents Hotte D’ASPIRATION DE Range Hood Safety Table of ContentsInstallation Requirements For vented installations, you also needTools and Parts Tools neededFor Mobile Home Installations Product DimensionsInstallation Clearances Location RequirementsVenting Requirements Example vent system Electrical Requirements¹⁄₄ x 10 8.3 cm x 25.4 cm Vent System Installation Instructions Determine Wiring Hole LocationTo wire through top To wire through rear wallInstall Range Hood Install Vent SystemWall Venting To make a 4 x 10½ 10.2 cm x 26.7 cm rectangle in the wallIt is recommended that the blower assembly be removed to Make the range hood lighter and easier to installFor vented installations To removeFor Vented Installations Only For Power Supply InstallationsMake Electrical Connection Complete Installation Reinstall blower For vented installation onlyFor non-vented recirculating installation only Install filtersCleaning Range Hood USERange Hood Care Range Hood ControlsU.S.A Assistance or ServiceCanada Whirlpool Corporation Major Appliance Warranty This limited warranty does not coverSécurité DE LA Hotte DE Cuisinière Votre sécurité et celle des autres est très importanteConservez CES Instructions Exigences demplacement Exigences DinstallationOutils et pièces Exigences concernant lévacuation Exemple de système de décharge Système de décharge de 3¹⁄₄ x 10 8,3 cm x 25,4 cmCalcul de la longueur effective du circuit dévacuation Système de décharge circulaire de 6 15,2 cm ou plusInstructions Dinstallation Préparation de lemplacementDéterminer lemplacement du trou de passage du câble Spécifications électriquesCâblage à travers le dessus du placard Décharge à travers le murCâblage à travers le mur arrière Installation du conduit dévacuation Découpage dune ouverture circulaire sous la partieSupérieure du placard DéposePour les installations avec décharge à l’extérieur Pour les installations à raccordement directAchever linstallation Pour les installations avec cordon dalimentation électriqueRaccordement électrique Évacuation horizontale Évacuation verticaleInstallation des filtres Vérification du fonctionnement de la hotteCommandes de la hotte de cuisinière Utilisation DE LA HotteEntretien DE LA Hotte NettoyageAssistance OU Service Au CanadaSi vous avez besoin de pièces de rechange Pour plus d’assistanceLa présente garantie limitée ne couvre pas Garantie DES Gros Appareils Ménagers Whirlpool CorporationW10240582A

99044506A, W10240582A specifications

The Whirlpool W10240582A and 99044506A represent two key components in home appliance functionality, as they are essential parts for Whirlpool refrigerators. These models are designed to enhance the efficiency and performance of your appliance, ensuring that your food and beverages remain fresh and properly stored.

One of the main features of both models is their compatibility with a wide range of Whirlpool refrigerator models, making them versatile components for consumers. This adaptability allows homeowners to easily replace old or malfunctioning parts without needing to purchase a completely new unit, ultimately saving time and money.

The W10240582A is known for its high-quality construction, which emphasizes durability and longevity. This part is often an essential component in the ice-making function of the refrigerator. By providing efficient ice production, the W10240582A ensures that users have a constant supply of ice for cooling beverages, making it an ideal choice for families and social gatherings.

On the other hand, the 99044506A is designed to optimize temperature control within the refrigerator. It serves as a thermostat, ensuring that the appliance maintains the ideal cooling temperature for food preservation. This technology is crucial not only for preventing food spoilage but also for energy efficiency, as a well-regulated cooling system uses less power, contributing to lower utility bills.

Both models showcase Whirlpool's commitment to innovation and user-friendliness. They are designed for easy installation, allowing even those with minimal technical skills to replace them without professional help. The clear instructions provided with these parts further simplify the process, making it accessible for the average homeowner.

In terms of characteristics, the W10240582A and 99044506A are both backed by Whirlpool's reputation for quality. They are engineered to meet rigorous safety and performance standards, ensuring reliable operation over time. Additionally, these components often come with warranty options, reflecting the brand’s confidence in their longevity and performance.

Overall, the Whirlpool W10240582A and 99044506A serve as excellent examples of how replacement parts can significantly enhance the functionality of household appliances. With their advanced features and compatibility, they play a vital role in maintaining the efficiency and effectiveness of Whirlpool refrigerators.