Whirlpool 99044506A It is recommended that the blower assembly be removed to, To remove

Page 9

4. It is recommended that the blower assembly be removed to

make the range hood lighter and easier to install.

To remove:

If using rectangular vent, attach rectangular damper/vent connectors to the range hood using 2 black sheet metal screws.

Disconnect blower wiring plug.

A

A

E

B

C

D

B

A.Blower

B.Blower wiring plug

Loosen, but do not remove, knurled nuts on mounting rods. Slip rods out of blower mounting brackets.

A B

A. Mounting rod

B. Knurled nut

IMPORTANT: To avoid damage, do not grasp blower by blower wheels.

Lift blower out and set aside.

5.Depending on your installation, remove either back or top wiring knockout.

6.For vented installations:

Check that the louver cover is installed in front of hood.

Depending on your installation, remove either top or rear rectangular vent knockout. If using round vent, remove top rectangular knockout.

NOTE: Do not remove rectangular knockouts if installation of range hood is to be non-venting (recirculating).

BC

A.Vertical vent

B.Black sheet metal screws

C.Hinge pin

D.Vent knockouts

E.Horizontal vent

If using round vent, attach vent transition piece (purchased separately) to range hood top using 2 black sheet metal screws.

NOTE: If the wall cap is directly behind the vent connector, the dampers in the connector and wall cap must not interfere with each other. Remove the vent connector damper if they interfere.

7.Lift the range hood up under cabinet and determine final location by centering beneath cabinet. Mark on the underside of cabinet the location of the 4 keyhole mounting slots on the range hood. Set range hood aside on a covered surface.

A

A. Keyhole slot

8.Use ¹⁄₈" (3 mm) drill bit and drill 4 pilot holes as shown.

A

A. Drill pilot hole

9

Image 9
Contents Hotte D’ASPIRATION DE Table of Contents Range Hood SafetyFor vented installations, you also need Installation RequirementsTools and Parts Tools neededProduct Dimensions For Mobile Home InstallationsInstallation Clearances Location RequirementsVenting Requirements Electrical Requirements Example vent system¹⁄₄ x 10 8.3 cm x 25.4 cm Vent System Determine Wiring Hole Location Installation InstructionsTo wire through top To wire through rear wallInstall Vent System Install Range HoodWall Venting To make a 4 x 10½ 10.2 cm x 26.7 cm rectangle in the wallMake the range hood lighter and easier to install It is recommended that the blower assembly be removed toFor vented installations To removeFor Power Supply Installations For Vented Installations OnlyMake Electrical Connection Reinstall blower For vented installation only Complete InstallationFor non-vented recirculating installation only Install filtersRange Hood USE CleaningRange Hood Care Range Hood ControlsAssistance or Service U.S.ACanada This limited warranty does not cover Whirlpool Corporation Major Appliance WarrantyVotre sécurité et celle des autres est très importante Sécurité DE LA Hotte DE CuisinièreConservez CES Instructions Exigences Dinstallation Exigences demplacementOutils et pièces Exigences concernant lévacuation Système de décharge de 3¹⁄₄ x 10 8,3 cm x 25,4 cm Exemple de système de déchargeCalcul de la longueur effective du circuit dévacuation Système de décharge circulaire de 6 15,2 cm ou plusPréparation de lemplacement Instructions DinstallationDéterminer lemplacement du trou de passage du câble Spécifications électriquesDécharge à travers le mur Câblage à travers le dessus du placardCâblage à travers le mur arrière Découpage dune ouverture circulaire sous la partie Installation du conduit dévacuationSupérieure du placard DéposePour les installations à raccordement direct Pour les installations avec décharge à l’extérieurPour les installations avec cordon dalimentation électrique Achever linstallationRaccordement électrique Évacuation horizontale Évacuation verticaleVérification du fonctionnement de la hotte Installation des filtresUtilisation DE LA Hotte Commandes de la hotte de cuisinièreEntretien DE LA Hotte NettoyageAu Canada Assistance OU ServiceSi vous avez besoin de pièces de rechange Pour plus d’assistanceGarantie DES Gros Appareils Ménagers Whirlpool Corporation La présente garantie limitée ne couvre pasW10240582A

99044506A, W10240582A specifications

The Whirlpool W10240582A and 99044506A represent two key components in home appliance functionality, as they are essential parts for Whirlpool refrigerators. These models are designed to enhance the efficiency and performance of your appliance, ensuring that your food and beverages remain fresh and properly stored.

One of the main features of both models is their compatibility with a wide range of Whirlpool refrigerator models, making them versatile components for consumers. This adaptability allows homeowners to easily replace old or malfunctioning parts without needing to purchase a completely new unit, ultimately saving time and money.

The W10240582A is known for its high-quality construction, which emphasizes durability and longevity. This part is often an essential component in the ice-making function of the refrigerator. By providing efficient ice production, the W10240582A ensures that users have a constant supply of ice for cooling beverages, making it an ideal choice for families and social gatherings.

On the other hand, the 99044506A is designed to optimize temperature control within the refrigerator. It serves as a thermostat, ensuring that the appliance maintains the ideal cooling temperature for food preservation. This technology is crucial not only for preventing food spoilage but also for energy efficiency, as a well-regulated cooling system uses less power, contributing to lower utility bills.

Both models showcase Whirlpool's commitment to innovation and user-friendliness. They are designed for easy installation, allowing even those with minimal technical skills to replace them without professional help. The clear instructions provided with these parts further simplify the process, making it accessible for the average homeowner.

In terms of characteristics, the W10240582A and 99044506A are both backed by Whirlpool's reputation for quality. They are engineered to meet rigorous safety and performance standards, ensuring reliable operation over time. Additionally, these components often come with warranty options, reflecting the brand’s confidence in their longevity and performance.

Overall, the Whirlpool W10240582A and 99044506A serve as excellent examples of how replacement parts can significantly enhance the functionality of household appliances. With their advanced features and compatibility, they play a vital role in maintaining the efficiency and effectiveness of Whirlpool refrigerators.