B&B Electronics CR-25E manual Final drive gear box Low speed housing, Pillow Block Bearings

Page 8

Installation & Operations Manual

 

 

CR-25E Cable Beam Barrier

Installation, Adjustment & Maintenance

7 of 31

1.5CR-25E Lubrication Instructions (Reference Drawing: 0025-0053-B)

Mechanism lubrication should be checked at least once per month.

Transmission (Item 5 on Assembly drawing):

First gear drive box ( High speed housing):

1.Remove the front door of the housing (roadway side).

2.Check oil by removing the oil level plug located on the left-hand vertical surface of the transmission a few inches below the motor.

Note: Some barriers may have site glasses.

a.If oil is visible, oil level is adequate - replace plug and go to next section.

b.If oil is not visible, go to step 3.

3.Remove fill plug of first gear box located on top of gear box facing door).

4.Fill the case to the level plug or site glass (removed in step two) with multi- grade Mobil SHC 629 or a direct replacement. (See recommended replacement oils on the following page.)

5.Replace plugs.

Final drive gear box (Low speed housing):

1.Remove the back door of the housing (counterweight side).

2.Check the oil level by removing the oil level plug located on the left-hand vertical surface of transmission. Note: Some barriers may have site glasses.

a.If oil is visible, oil level is adequate - replace the plug and go to next section.

b.If oil is not visible, go to Step 2.

2.Remove oil fill plug on final gear box, on the left-hand vertical surface, top.

3.Fill the case to the level plug or site glass (removed in step one) with multi-grade Mobil SHC 629 or a direct replacement. (see recommended replacement oils on the following page)

4.Replace plugs.

Pillow Block Bearings:

1.Grease with Texaco Marfak 2 or equal.

2.Wipe off excess.

NOTE: 1 pillow block bearing is located inside unit on main shaft.

© 2007 B&B ARMR

WWW.BB-ARMR.COM

(800) 367-0387

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Corporate Technical Support Field Service Support Made in the USAIntroduction WelcomeHow to Contact Us Corporate Technical Support Service SupportTable of Contents INSTALLATION, Adjustment and Maintenance Have been installedHousing Operating mechanismCarefully. Consult Factory if Problem is not Found Necessary, refer to the enclosed installation instructions CR-25E Start Up InstructionsCR-25E Shut Down Instructions CR-25E Emergency Operation InstructionsFinal drive gear box Low speed housing Pillow Block BearingsLimit Switch Drive Chain Item Lubrication Replacement InstructionsConnecting Rod Ends Items11 Recommended Replacement Oils for CR-25E To remove the old assembly To mount the new assemblyMotor Replacement Instructions Main Power Switch S1 OFF Before Beginning Limit Switch Replacement InstructionsDisconnect Barrier Power by Throwing Indications Problem Solution Field Balancing InstructionsGate Arm Balancing Instructions Calculating Counterweight RequirementsCounterweight Sizes Adjusting the Barrier Movement 2007 B&B Armr 800 2007 B&B Armr 800 2007 B&B Armr 800 Specifications Limit Switch TransmissionMotor Braking MechanismSafety SWITCHES, Terminal Blocks and Wiring Energy Absorption CablesCable Anchoring System Quality AssuranceAccessories and Major Components Housing Assembly 0025-0050-AOperator Assembly 0025-0053-B Brake Assembly 0040-0023-C Limit Switch Assembly 0040-0009-F Motor Cut Sheet Installation 22’ Clear Opening System DrawingsInstallation 14’ Clear Opening Wiring Warranty

CR-25E specifications

B&B Electronics CR-25E is a robust and versatile device designed for fulfilling the needs of industrial communication systems. Characterized by its reliability and advanced functionality, the CR-25E is widely recognized in the automation and control sectors.

One of the key features of the CR-25E is its high-speed data transmission capabilities. With support for both RS-232 and RS-485 communication protocols, the device ensures seamless integration across various systems. The CR-25E operates at speeds up to 115.2 Kbps, allowing for rapid data exchange, which is crucial in applications like robotic controls, sensors, and monitoring systems.

Another standout characteristic of the CR-25E is its built-in isolation features. With 2.5 kV isolation on the serial lines, it protects the connected equipment from voltage spikes and noise, significantly enhancing the reliability of the communication link. This isolation effectiveness is particularly valuable in environments rife with electrical interference, as it ensures stable operation and long-lasting performance.

The CR-25E supports multiple power input options, including AC and DC power supplies. This flexibility enables easy integration into existing systems without the need for extensive modifications or additional components. The device also features wide input voltage ranges, thus accommodating different industrial environments and requirements.

In terms of mounting options, the CR-25E is designed with user-friendliness in mind. The compact design and DIN rail compatibility facilitate easy installation in control panels, maximizing space efficiency while maintaining accessible connectivity for maintenance or troubleshooting.

For monitoring and configuration, the CR-25E integrates effortlessly with various industrial software and applications. The device features diagnostic LEDs to provide real-time indications of operational status, simplifying troubleshooting by allowing users to quickly identify issues.

In summary, B&B Electronics CR-25E stands out due to its high-speed data transmission, robust isolation features, versatile power input capabilities, and user-friendly design. These attributes make it a preferred choice among engineers and technicians in the field of industrial communication, ensuring that systems remain efficient, reliable, and effective in demanding operational settings.
Top Page Image Contents