Frymaster 8196428 manual General, Replacing a Controller, Replacing Component Box Components

Page 5

YFPRE SERIES ELECTRIC FRYERS

CHAPTER 1: SERVICE PROCEDURES

1.1 General

Before performing any maintenance on your Frymaster fryer, disconnect the fryer from the electrical power supply.

When electrical wires are disconnected, it is recommended that they be marked to facilitate re- assembly.

1.2 Replacing a Controller

1.Disconnect the fryer from the electrical power supply.

2.The controller bezel is held in place by tabs at the top and bottom. Slide the metal bezel up to disengage the lower tabs. Then slide the bezel down to disengage the upper tabs.

3.Remove the two screws from the upper corners of the control panel. The control panel is hinged at the bottom and swings open from the top.

4.Unplug the wiring harness from the connector on the back of the controller and disconnect the grounding wire from terminal adjacent to the connector. Remove the control panel assembly by lifting it from the hinged slots in the control panel frame.

15-Pin Connector

Ground Wire Terminal

5.Remove the controller from the control panel assembly and install the replacement controller. Reinstall the control panel assembly by reversing Steps 1 and 2.

1.3 Replacing Component Box Components

1.Disconnect the fryer from the electrical power supply.

2.The controller bezel is held in place by tabs at the top and bottom. Slide the metal bezel up to disengage the lower tabs. Then slide the bezel down to disengage the upper tabs.

1-1

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Yfpre Series Electric Fryers Hour Service HotlinePage Page Yfpre Series Electric Fryers Table of Contents Replacing Component Box Components GeneralReplacing a Controller Replacing a High-Limit Thermostat Replacing a Temperature Probe Page Replacing a Heating Element Replacing Contactor Box Components Replacing a Frypot Page Drain Safety Switch Page Disconnect flexlines indicated by the arrows Replacing the Filter Transformer or Filter Relay Diagnostic LED Legend Interface Board Diagnostic ChartProbe Resistance Chart Probe Resistance ChartComponent Wiring Standard Wiring Yfpre Tilt Switch Wiring Terminal Block Wiring Contactor Delta Configuration, 3 Phase Contactor Single Phase Accessories Yfpre Series Electric Fryers Parts ListCabinetry 106-9431 Drain Components Not illustrated Tilt Switch Assembly Lane Controller Contactor Box Component Box Component Box to Filter Pump Harness Contactor Box Harness Assembly, MDI, 9-Pin Right ElementMain Wiring Harnesses Component Box and Filter Pump Filtration System Components RingPkg. of 5 used with Item Frypot and Associated Parts Wiring Connectors and Pin Connectors Fasteners Nuts, Bolts, Screws, Washers This page Intentionally Left Blank Service Hotline

8196428 specifications

The Frymaster 8196428 is a high-performance commercial fryer designed for efficiency and reliability in bustling kitchen environments. Known for its robust construction and innovative features, the Frymaster 8196428 stands out as a preferred choice for restaurants, cafeterias, and fast-food outlets.

One of the key characteristics of the Frymaster 8196428 is its advanced heating technology. This fryer utilizes a powerful heating system that ensures rapid temperature recovery, allowing for consistent cooking results, even during peak hours. This feature is essential in maintaining food quality and minimizing cook times, which is crucial in a fast-paced setting.

The Frymaster 8196428 is equipped with a digital control system that simplifies the frying process. The precise digital thermostat allows for accurate temperature settings, ensuring that the oil remains at the optimal frying temperature. This not only enhances the flavor and texture of the food but also contributes to food safety by preventing undercooking or overcooking.

Another significant feature is its efficient oil management system. The Frymaster 8196428 is designed with a high-capacity oil tank, allowing for extended frying sessions without the need for frequent oil changes. This not only saves costs but also reduces waste, making it an environmentally friendly option. Additionally, the fryer’s oil filtration system helps in prolonging oil life by filtering out food particles, ensuring that the oil remains clean and effective for longer periods.

The construction of the Frymaster 8196428 is another highlight. Made with durable stainless steel, the fryer is built to withstand the rigors of everyday use while remaining easy to clean. Its compact design ensures it can fit seamlessly into various kitchen layouts, making it an adaptable choice for different business sizes.

Safety features are paramount in the Frymaster 8196428’s design. It incorporates built-in safety mechanisms, such as automatic shut-off functions and cool-to-the-touch handles, to protect users from accidental burns and other hazards.

In summary, the Frymaster 8196428 is an exemplary commercial fryer that combines advanced technology, efficiency, and user-friendly features. Its precise temperature control, high-capacity oil management system, durable construction, and safety measures make it a reliable choice for any commercial kitchen aiming to serve high-quality fried foods with ease and consistency.
Top Page Image Contents