Frymaster 8196428 manual Drain Safety Switch

Page 13

21.Position the element tube assembly in the frypot and reinstall the machine screws and nuts removed in Step 14.

22.Reconnect the oil return flexline(s) to the frypot, and replace aluminum tape, if necessary, to secure heater strips to the flexline(s).

23.Insert the high-limit thermostat leads disconnected in Step 13 (see illustration on page 1-3 for pin positions).

24.Reconnect the drain safety switch wiring to the switch in accordance with the diagram below then reinstall the switch cover.

 

RIGHT

ORANGE Pin 15 J4

DRAIN SAFETY SWITCH

BLUE Pin 1 C6

 

25.Reinstall the drain tube assembly.

26.Reinstall the top cap, control panel, component box, tilt housing and back panels.

27.Reinstall the controller in the control panel frame and reconnect the wiring harnesses and ground wire.

28.Reposition the fryer under the exhaust hood and reconnect it to the electrical power supply.

1.9Built-in Filtration System Service Procedures 1.9.1 Filtration System Problem Resolution

One of the most common causes of filtration problems is placing the filter paper on the bottom of the filter pan rather than over the filter screen.

CAUTION

Ensure that filter screen is in place prior to filter paper placement and filter pump operation. Improper screen placement is the primary cause of filtration system malfunction.

Whenever the complaint is “the pump is running, but no oil is being filtered,” check the installation of the filter paper, and ensure that the correct size is being used. While you are checking the filter paper, verify that the O-rings on the pick-up tube of the filter pan are in good condition. Missing or worn O-rings allow the pump to take in air and decrease its efficiency.

If the pump motor overheats, the thermal overload will trip and the motor will not start until it is reset. If the pump motor does not start, press the red reset switch (button) located on the rear of the motor at the front of the fryer.

1-9

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Yfpre Series Electric Fryers Hour Service HotlinePage Page Yfpre Series Electric Fryers Table of Contents Replacing a Controller GeneralReplacing Component Box Components Replacing a High-Limit Thermostat Replacing a Temperature Probe Page Replacing a Heating Element Replacing Contactor Box Components Replacing a Frypot Page Drain Safety Switch Page Disconnect flexlines indicated by the arrows Replacing the Filter Transformer or Filter Relay Diagnostic LED Legend Interface Board Diagnostic ChartProbe Resistance Chart Probe Resistance ChartComponent Wiring Standard Wiring Yfpre Tilt Switch Wiring Terminal Block Wiring Contactor Delta Configuration, 3 Phase Contactor Single Phase Accessories Yfpre Series Electric Fryers Parts ListCabinetry 106-9431 Drain Components Not illustrated Tilt Switch Assembly Lane Controller Contactor Box Component Box Component Box to Filter Pump Harness Contactor Box Harness Assembly, MDI, 9-Pin Right ElementMain Wiring Harnesses Component Box and Filter Pump Filtration System Components RingPkg. of 5 used with Item Frypot and Associated Parts Wiring Connectors and Pin Connectors Fasteners Nuts, Bolts, Screws, Washers This page Intentionally Left Blank Service Hotline

8196428 specifications

The Frymaster 8196428 is a high-performance commercial fryer designed for efficiency and reliability in bustling kitchen environments. Known for its robust construction and innovative features, the Frymaster 8196428 stands out as a preferred choice for restaurants, cafeterias, and fast-food outlets.

One of the key characteristics of the Frymaster 8196428 is its advanced heating technology. This fryer utilizes a powerful heating system that ensures rapid temperature recovery, allowing for consistent cooking results, even during peak hours. This feature is essential in maintaining food quality and minimizing cook times, which is crucial in a fast-paced setting.

The Frymaster 8196428 is equipped with a digital control system that simplifies the frying process. The precise digital thermostat allows for accurate temperature settings, ensuring that the oil remains at the optimal frying temperature. This not only enhances the flavor and texture of the food but also contributes to food safety by preventing undercooking or overcooking.

Another significant feature is its efficient oil management system. The Frymaster 8196428 is designed with a high-capacity oil tank, allowing for extended frying sessions without the need for frequent oil changes. This not only saves costs but also reduces waste, making it an environmentally friendly option. Additionally, the fryer’s oil filtration system helps in prolonging oil life by filtering out food particles, ensuring that the oil remains clean and effective for longer periods.

The construction of the Frymaster 8196428 is another highlight. Made with durable stainless steel, the fryer is built to withstand the rigors of everyday use while remaining easy to clean. Its compact design ensures it can fit seamlessly into various kitchen layouts, making it an adaptable choice for different business sizes.

Safety features are paramount in the Frymaster 8196428’s design. It incorporates built-in safety mechanisms, such as automatic shut-off functions and cool-to-the-touch handles, to protect users from accidental burns and other hazards.

In summary, the Frymaster 8196428 is an exemplary commercial fryer that combines advanced technology, efficiency, and user-friendly features. Its precise temperature control, high-capacity oil management system, durable construction, and safety measures make it a reliable choice for any commercial kitchen aiming to serve high-quality fried foods with ease and consistency.
Top Page Image Contents