Frymaster 8196428 manual Replacing a High-Limit Thermostat

Page 6

3.Remove the two screws from the upper corners of the control panel and allow the control panel to swing down.

4.Unplug the wiring harness from the 15-pin connector on the interface board and disconnect the grounding wire from terminal adjacent to the 15-pin connector on the back of the controller. Remove the control panel assembly by lifting it from the hinge slots in the control panel frame.

5.Disconnect the wiring from the component to be replaced, being sure to make a note of where each wire was connected.

6.Dismount the component to be replaced and install the new component, being sure that any required spacers, insulation, washers, etc. are in place.

NOTE: If more room to work is required, the control panel frame assembly may be removed by removing the hex head screws that secure it to the fryer cabinet (see illustration below). Removing the component box itself from the fryer is not recommended due to the difficulty involved in disconnecting and reconnecting the oil-return valve rods, which pass through openings in the component box.

7.Reconnect the wiring disconnected in Step 3, referring to your notes and the wiring diagrams on the fryer door to ensure that the connections are properly made. Also, verify that no other wiring was disconnected accidentally during the replacement process.

8.Reverse Steps 1 through 4 to complete the replacement and return the fryer to service.

1.4 Replacing a High-Limit Thermostat

1.Remove the filter pan and lid from the unit. Drain the frypot into a Shortening Disposal Unit (SDU) or other appropriate metal container.

DANGER

DO NOT drain more than one full frypot or two split frypots into the SDU at one time.

2.Disconnect the fryer from the electrical power supply and reposition it to gain access to the rear of the fryer.

1-2

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Hour Service Hotline Yfpre Series Electric FryersPage Page Yfpre Series Electric Fryers Table of Contents General Replacing a ControllerReplacing Component Box Components Replacing a High-Limit Thermostat Replacing a Temperature Probe Page Replacing a Heating Element Replacing Contactor Box Components Replacing a Frypot Page Drain Safety Switch Page Disconnect flexlines indicated by the arrows Replacing the Filter Transformer or Filter Relay Interface Board Diagnostic Chart Diagnostic LED LegendProbe Resistance Chart Probe Resistance ChartComponent Wiring Standard Wiring Yfpre Tilt Switch Wiring Terminal Block Wiring Contactor Delta Configuration, 3 Phase Contactor Single Phase Yfpre Series Electric Fryers Parts List AccessoriesCabinetry 106-9431 Drain Components Not illustrated Tilt Switch Assembly Lane Controller Contactor Box Component Box Contactor Box Harness Assembly, MDI, 9-Pin Right Element Component Box to Filter Pump HarnessMain Wiring Harnesses Component Box and Filter Pump Filtration System Components RingPkg. of 5 used with Item Frypot and Associated Parts Wiring Connectors and Pin Connectors Fasteners Nuts, Bolts, Screws, Washers This page Intentionally Left Blank Service Hotline

8196428 specifications

The Frymaster 8196428 is a high-performance commercial fryer designed for efficiency and reliability in bustling kitchen environments. Known for its robust construction and innovative features, the Frymaster 8196428 stands out as a preferred choice for restaurants, cafeterias, and fast-food outlets.

One of the key characteristics of the Frymaster 8196428 is its advanced heating technology. This fryer utilizes a powerful heating system that ensures rapid temperature recovery, allowing for consistent cooking results, even during peak hours. This feature is essential in maintaining food quality and minimizing cook times, which is crucial in a fast-paced setting.

The Frymaster 8196428 is equipped with a digital control system that simplifies the frying process. The precise digital thermostat allows for accurate temperature settings, ensuring that the oil remains at the optimal frying temperature. This not only enhances the flavor and texture of the food but also contributes to food safety by preventing undercooking or overcooking.

Another significant feature is its efficient oil management system. The Frymaster 8196428 is designed with a high-capacity oil tank, allowing for extended frying sessions without the need for frequent oil changes. This not only saves costs but also reduces waste, making it an environmentally friendly option. Additionally, the fryer’s oil filtration system helps in prolonging oil life by filtering out food particles, ensuring that the oil remains clean and effective for longer periods.

The construction of the Frymaster 8196428 is another highlight. Made with durable stainless steel, the fryer is built to withstand the rigors of everyday use while remaining easy to clean. Its compact design ensures it can fit seamlessly into various kitchen layouts, making it an adaptable choice for different business sizes.

Safety features are paramount in the Frymaster 8196428’s design. It incorporates built-in safety mechanisms, such as automatic shut-off functions and cool-to-the-touch handles, to protect users from accidental burns and other hazards.

In summary, the Frymaster 8196428 is an exemplary commercial fryer that combines advanced technology, efficiency, and user-friendly features. Its precise temperature control, high-capacity oil management system, durable construction, and safety measures make it a reliable choice for any commercial kitchen aiming to serve high-quality fried foods with ease and consistency.
Top Page Image Contents