Jenn-Air W10274318A, LI3V3A Electrical Requirements, Rear discharge, Example vent system

Page 6

Rear discharge

This range hood can be vented directly out the back using the 3¼" x 10" (8.3 cm x 25.4 cm) rectangular damper (supplied) along with a 3¼" x 10" (8.3 cm x 25.4 cm) rectangular vent system (not supplied). See “Install Range Hood” section for details for installing the damper.

Roof Venting

Wall Venting

 

(top or rear discharge)

Example vent system

3¹⁄₄" x 10"

 

(8.3 x 25.4 cm)

 

elbow

Wall cap

6 ft (1.8 m)

A

B

B

A

2ft

(0.6 m)

Maximum Recommended Length

= 35 ft (10.7 m)

1

- 90° elbow

= 5.0 ft (1.5 m)

8 ft (2.4 m) straight

= 8.0 ft (2.4 m)

1

- wall cap

= 0.0 ft (0.0 m)

 

 

Length of 3¹⁄₄" x 10" (8.3 cm x 25.4 cm)

= 13.0 ft (3.9 m)

A. Roof cap

A. Wall cap

B. 3¹⁄₄" x 10" (8.3 x 25.4 cm)

B. 3¹⁄₄" x 10" (8.3 x 25.4 cm)

rectangular metal vent

rectangular metal vent

Calculating Vent System Length

To calculate the length of the system you need, add the equivalent feet (meters) for each vent piece used in the system.

3¹⁄₄" x 10" (8.3 cm x 25.4 cm) Vent System

Vent Piece

3¹⁄₄" x 10" (8.3 cm x 25.4 cm)

5.0 ft

90° elbow

(1.5 m)

 

 

3¹⁄₄" x 10" (8.3 cm x 25.4 cm)

12.0 ft

flat elbow

(3.7 m)

 

 

3¹⁄₄" x 10" (8.3 cm x 25.4 cm)

0.0 ft

wall cap

(0.0 m)

 

 

system

Electrical Requirements

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

A 120 Volt, 60 Hz., AC only, 15-amp, fused electrical circuit is required.

If the house has aluminum wiring, follow the procedure below:

1.Connect a section of solid copper wire to the pigtail leads.

2.Connect the aluminum wiring to the added section of copper wire using special connectors and/or tools designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices.

Wire sizes and connections must conform with the rating of the appliance as specified on the model/serial rating plate. The model/serial plate is located behind the filter on the rear wall of the range hood.

Wire sizes must conform to the requirements of the National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

6

Image 6
Contents 30 ET 36 76,2 CM ET 91,4 CM LI3V3A/W10274318ARange Hood Safety Table of ContentsImportant Safety Instructions Installation Requirements Tools and PartsLocation Requirements Venting Requirements Example vent system Electrical RequirementsRear discharge Calculating Vent System LengthTo wire through top Installation InstructionsDetermine Wiring Hole Location Prepare LocationWall Venting Under Cabinet To make a 3½ x 10½ 8.9 cm x 26.7 cm rectangle in the wallInstall Range Hood Make Electrical ConnectionComplete Preparation Range Hood USE Install Vent Covers OptionalComplete Installation Range Hood ControlsExterior Surfaces CleaningRange Hood Care Metal Grease FilterWiring Diagram U.S.A Assistance or ServiceAccessories CanadaJENN-AIRMAJOR Appliance Warranty This limited warranty does not coverSécurité DE LA Hotte DE Cuisinière Votre sécurité et celle des autres est très importanteImportantes Instructions DE Sécurité Exigences Dinstallation Exigences d’emplacementOutils et pièces Vue arrière Dimensions du produit Dimensions du placard Vue de faceExigences concernant l’évacuation Pour un fonctionnement efficace et silencieuxMéthodes d’évacuation Installations dans les régions au climat froidAir d’appoint Calcul de la longueur effective du circuit d’évacuationInstructions Dinstallation Préparation de lemplacementSpécifications électriques Décharge à travers le mur sous un placard Déterminer l’emplacement du trou de passage du câbleDécharge à travers le toit Câblage à travers le sommet du placardInstallation de la hotte Achever la préparationRaccordement électrique Commandes de la hotte de cuisinière Installation des cache-conduits facultatifAchever l’installation Utilisation DE LA HotteNettoyage Remplacement d’une lampe à halogèneEntretien DE LA Hotte Surfaces externesSchéma DE Câblage Assistance OU Service AccessoiresW10274318A 2009 All rights reserved

LI3V3A, W10274318A specifications

The Jenn-Air LI3V3A is a state-of-the-art built-in refrigerator that exemplifies the blend of style and performance, designed to meet the demands of modern kitchens. One of its standout features is the sleek, integrated design that allows it to seamlessly blend into your cabinetry, creating a cohesive look while providing unmatched functionality.

With a net capacity of 20.5 cubic feet, the LI3V3A provides ample space for both fresh and frozen foods. Its innovative layout includes adjustable shelves and a spacious crisper drawer, making it easy to organize and access your groceries. The refrigerator features a special TriCooling system, which utilizes three separate cooling systems to maintain ideal temperature and humidity levels in each compartment. This ensures that fruits, vegetables, and perishable items stay fresher for longer, reducing food waste and preserving flavor.

The LI3V3A also integrates advanced technologies like the Dual Evaporator system. This feature prevents the mixing of air between the refrigerator and freezer compartments, thereby maintaining optimal humidity levels and preventing the transfer of odors. Additionally, this refrigerator boasts a noticeable reduction in energy consumption, thanks to its Energy Star certification; a testament to its efficiency and environmentally conscious design.

Another significant characteristic is its innovative internal water filtration system, featuring a water and ice dispenser that provides convenient access to chilled water and ice cubes. The refrigerator’s water filter is easy to access, making it simple to replace when needed, ensuring clean and safe drinking water at all times.

The user-friendly touchscreen control panel simplifies settings adjustments, allowing users to easily modify temperature settings, control the ice maker, and monitor filter status. Moreover, features like door alarms remind users when the door is left open, helping to maintain the cold inside and enhancing energy efficiency.

Overall, the Jenn-Air LI3V3A, W10274318A model stands out not just for its aesthetic appeal but also for its robust functionality, energy efficiency, and commitment to food preservation. This makes it an ideal choice for anyone seeking a high-performance refrigerator that enhances both the kitchen's style and the quality of its contents.