Install Range Hood, Make Electrical Connection

Complete Preparation

1.Determine the required height for the home power supply cable and drill a 1¼" (3.2 cm) hole at this location.

2.Run the home power supply cable according to the National Electrical Code or CSA Standards and local codes and ordinances. There must be enough ½" conduit and wires from the fused disconnect (or circuit breaker) box to make the connection in the hood’s electrical terminal box.

NOTE: Do not reconnect power until installation is complete.

3.Remove terminal box cover and set aside.

4.Remove knockout from the top of the vent hood and install a UL listed or CSA approved ½" strain relief.

Install Range Hood

1.Remove the grease filters. See the “Range Hood Care” section.

2.Depending on your installation, remove either top or rear rectangular vent knockout. If using round vent, remove top rectangular knockout.

NOTE: If the wall cap is directly behind the 3¼" x 10" (8.3 x

25.4 cm) rectangular vent connector, check that the damper and the wall cap do not interfere with each other. Remove the damper from the 3¼" x 10" ( 8.3 x 25.4 cm) rectangular vent connector if they interfere.

5.Using 2 or more people, lift the hood into final position. Feed enough electrical wire through the ½" UL listed or CSA approved strain relief to make connections in the terminal box. Tighten the strain relief screws.

6.Position the range hood so that the large end of the keyhole slots are over the mounting screws. Then push the hood toward the wall (for cabinet mounting) or allow the range hood to slide down to the marked mounting height (for wall mounting) so that the screws are in the neck of the slots. Tighten the mounting screws, making sure the screws are in the narrow neck of slots. (For wall mount, check that the hood is level).

7.Connect ventwork to hood. Seal joints with clamps to make secure and airtight.

8.Check that back draft dampers work properly.

Make Electrical Connection

A. Vent knockouts

Make sure damper pivot is nearest to top/back edge of range hood.

3.Remove tape from damper flap.

NOTE: The 3¼" x 10" (8.3 x 25.4 cm) rectangular damper can be installed up to 1" (2.5 cm) on either side of the hood center to accommodate off-center duct work.

4.Attach the 3¼" x 10" (8.3 x 25.4 cm) rectangular vent connector to the range hood using sheet metal screws.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

1.Disconnect power.

D F

A. White wires B. Black wires

C. UL listed wire connector

D. Green (or bare) and yellow-green ground wire E. Home power supply cable

F. UL listed or CSA approved ½" strain relief

A.Top venting

B.Sheet metal screws

C.Hinge pin

D.Vent knockouts

E.Rear venting

2.Use UL listed wire connectors and connect white wires (A) together.

LI3V3A, W10274318A specifications

The Jenn-Air LI3V3A is a state-of-the-art built-in refrigerator that exemplifies the blend of style and performance, designed to meet the demands of modern kitchens. One of its standout features is the sleek, integrated design that allows it to seamlessly blend into your cabinetry, creating a cohesive look while providing unmatched functionality.

With a net capacity of 20.5 cubic feet, the LI3V3A provides ample space for both fresh and frozen foods. Its innovative layout includes adjustable shelves and a spacious crisper drawer, making it easy to organize and access your groceries. The refrigerator features a special TriCooling system, which utilizes three separate cooling systems to maintain ideal temperature and humidity levels in each compartment. This ensures that fruits, vegetables, and perishable items stay fresher for longer, reducing food waste and preserving flavor.

The LI3V3A also integrates advanced technologies like the Dual Evaporator system. This feature prevents the mixing of air between the refrigerator and freezer compartments, thereby maintaining optimal humidity levels and preventing the transfer of odors. Additionally, this refrigerator boasts a noticeable reduction in energy consumption, thanks to its Energy Star certification; a testament to its efficiency and environmentally conscious design.

Another significant characteristic is its innovative internal water filtration system, featuring a water and ice dispenser that provides convenient access to chilled water and ice cubes. The refrigerator’s water filter is easy to access, making it simple to replace when needed, ensuring clean and safe drinking water at all times.

The user-friendly touchscreen control panel simplifies settings adjustments, allowing users to easily modify temperature settings, control the ice maker, and monitor filter status. Moreover, features like door alarms remind users when the door is left open, helping to maintain the cold inside and enhancing energy efficiency.

Overall, the Jenn-Air LI3V3A, W10274318A model stands out not just for its aesthetic appeal but also for its robust functionality, energy efficiency, and commitment to food preservation. This makes it an ideal choice for anyone seeking a high-performance refrigerator that enhances both the kitchen's style and the quality of its contents.