Jenn-Air W10274318A, LI3V3A Installation Requirements, Tools and Parts, Location Requirements

Page 4

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed

Level

Drill with 1¼" (3.0 cm), ³⁄₁₆" (4.8 mm), ¹⁄₈" (3.0 mm), and ⁵⁄₁₆" (7.9 mm) drill bits

Pencil

Wire stripper or utility knife

Tape measure or ruler

Pliers

Caulking gun and weatherproof caulking compound

Vent clamps

Jigsaw or keyhole saw

Flat-blade screwdriver

Metal snips

Phillips screwdriver

Metric Allen wrench set

Parts needed

Home power supply cable

½" (12.7 mm) UL listed or CSA approved strain relief

3 UL listed wire connectors

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located behind the left filter on the rear wall of the vent hood.

Canopy hood location should be away from strong draft areas, such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance.

Grounded electrical outlet is required. See “Electrical Requirements” section.

The canopy hood is factory set for venting through the roof or wall.

All openings in ceiling and wall where canopy hood will be installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local codes.

Product Dimensions

1 wall or roof cap

Metal vent system

Front View

³⁄₈"

2⁹⁄₁₆"

(6.5 cm)

Parts supplied

Remove parts from packages. Check that all parts are included.

Hood canopy assembly with ventilator and light bulbs installed

3¼" x 10" (8.3 x 25.4 cm) rectangular vent connector

2 metal grease filters for 30" (76.2 cm) model

3 metal grease filters for 36" (91.4 cm) model

T20 Torx®† adapter

4 - 5 x 45 mm mounting screws

6 - 4.5 x 13 mm screws

3 - 4 x 8 mm screws

4 - 10 x 50 wall anchors

(1.0 cm)

7½"

(19.0 cm)

29¹⁄₈" (74.0 cm): 30" (76.2 cm) models

35¹⁄₈" (89.2 cm): 36" (91.4 cm) models

12" (30.5 cm)

10" (25.4 cm)

2" (5.1 cm)

23" (58.4 cm)

30" (76.2 cm) 36" (91.4 cm)

†®TORX is a registered trademark of Acument Intellectual Properties, LLC.

4

Image 4
Contents 30 ET 36 76,2 CM ET 91,4 CM LI3V3A/W10274318ARange Hood Safety Table of ContentsImportant Safety Instructions Tools and Parts Installation RequirementsLocation Requirements Venting Requirements Electrical Requirements Rear dischargeExample vent system Calculating Vent System LengthInstallation Instructions Determine Wiring Hole LocationTo wire through top Prepare LocationWall Venting Under Cabinet To make a 3½ x 10½ 8.9 cm x 26.7 cm rectangle in the wallMake Electrical Connection Install Range HoodComplete Preparation Install Vent Covers Optional Complete InstallationRange Hood USE Range Hood ControlsCleaning Range Hood CareExterior Surfaces Metal Grease FilterWiring Diagram Assistance or Service AccessoriesU.S.A CanadaJENN-AIRMAJOR Appliance Warranty This limited warranty does not coverSécurité DE LA Hotte DE Cuisinière Votre sécurité et celle des autres est très importanteImportantes Instructions DE Sécurité Exigences d’emplacement Exigences DinstallationOutils et pièces Dimensions du produit Dimensions du placard Vue de face Exigences concernant l’évacuationVue arrière Pour un fonctionnement efficace et silencieuxInstallations dans les régions au climat froid Air d’appointMéthodes d’évacuation Calcul de la longueur effective du circuit d’évacuationPréparation de lemplacement Instructions DinstallationSpécifications électriques Déterminer l’emplacement du trou de passage du câble Décharge à travers le toitDécharge à travers le mur sous un placard Câblage à travers le sommet du placardInstallation de la hotte Achever la préparationRaccordement électrique Installation des cache-conduits facultatif Achever l’installationCommandes de la hotte de cuisinière Utilisation DE LA HotteRemplacement d’une lampe à halogène Entretien DE LA HotteNettoyage Surfaces externesSchéma DE Câblage Assistance OU Service AccessoiresW10274318A 2009 All rights reserved

LI3V3A, W10274318A specifications

The Jenn-Air LI3V3A is a state-of-the-art built-in refrigerator that exemplifies the blend of style and performance, designed to meet the demands of modern kitchens. One of its standout features is the sleek, integrated design that allows it to seamlessly blend into your cabinetry, creating a cohesive look while providing unmatched functionality.

With a net capacity of 20.5 cubic feet, the LI3V3A provides ample space for both fresh and frozen foods. Its innovative layout includes adjustable shelves and a spacious crisper drawer, making it easy to organize and access your groceries. The refrigerator features a special TriCooling system, which utilizes three separate cooling systems to maintain ideal temperature and humidity levels in each compartment. This ensures that fruits, vegetables, and perishable items stay fresher for longer, reducing food waste and preserving flavor.

The LI3V3A also integrates advanced technologies like the Dual Evaporator system. This feature prevents the mixing of air between the refrigerator and freezer compartments, thereby maintaining optimal humidity levels and preventing the transfer of odors. Additionally, this refrigerator boasts a noticeable reduction in energy consumption, thanks to its Energy Star certification; a testament to its efficiency and environmentally conscious design.

Another significant characteristic is its innovative internal water filtration system, featuring a water and ice dispenser that provides convenient access to chilled water and ice cubes. The refrigerator’s water filter is easy to access, making it simple to replace when needed, ensuring clean and safe drinking water at all times.

The user-friendly touchscreen control panel simplifies settings adjustments, allowing users to easily modify temperature settings, control the ice maker, and monitor filter status. Moreover, features like door alarms remind users when the door is left open, helping to maintain the cold inside and enhancing energy efficiency.

Overall, the Jenn-Air LI3V3A, W10274318A model stands out not just for its aesthetic appeal but also for its robust functionality, energy efficiency, and commitment to food preservation. This makes it an ideal choice for anyone seeking a high-performance refrigerator that enhances both the kitchen's style and the quality of its contents.