Avanti BD6000 instruction manual Operating Your Beer Dispenser, Care and Maintenance

Page 16

?Converting Your Beer Dispenser To An “All Refrigerator”

1.Turn the control knob to the “OFF” position.

2.Close the main valve on the CO2 cylinder.

3.Close the secondary shut-off valve on the regulator pipe.

4.Close the connection between the beer keg and the keg coupler.

5.Drain any remaining beer from the lines.

6.Disconnect the beer line and CO2 air line from the keg coupler .

7.Remove the beer keg and bottom metal plate .

8.Remove the keg coupler.

9.Disconnect the air line from the CO2 cylinder.

10.Remove the CO2 air line from cabinet plug

11.Replace the air line rear cabinet plug

12.Remove the beer tower. Also pull the beer line thru the top of the cabinet.

13.Replace the top cabinet plug.

14.Remove the guard rail and cover the guard rail installation holes by the provided plugs.

15.Install the two wire shelves to the desinaged positions .

16.Adjust temperature as desired.

OPERATING YOUR BEER DISPENSER

?Setting The Temperature

To start, turn the temperature control knob to the maximum setting (6) to achieve coldest position quickly. Allow the unit to run for 3 hours. Temperature range of the thermostat goes from 36°F to 45°F 2(.2ºC to 7.2ºC).

Optimum temperature for serving draught beer is between 34°F – 38°F (1.1ºC – 3.3ºC) and that is a key factor to consider in storing and dispensing draught beer.

To turn off the Beer Dispenser, turn the control knob to the “OFF” position.

NOTE: Keep an accurate thermometer handy and adjust temperature control setting as necessary or according to your needs.

?Automatic Defrosting

There is no need to defrost the Beer Dispenser. Defros t water collects and passes through the drain outlet in the rear wall into a tray located above the compressor, where it evaporates.

NOTE:

?IF THE UNIT IS UNPLUGGED, POWER LOST, OR TURNED OFF, YOU MUST WAIT 3 TO 5 MINUTES BEFORE RESTARTING THE UNIT. IF YOU ATTEMPT TO RESTART BEFORE THIS TIME DELAY, THE BEER DISPENSER WILL NOT START.

?TURNING THE TEMPERATURE CONTROL TO “OFF” POSITION STOPS THE COOLING CYCLE BUT DOES NOT SHUT OFF THE POWER TO THE UNIT.

CARE AND MAINTENANCE

?Cleaning Your Beer Dispenser

?Turn the temperature control to "OFF", unplug the Beer Dispenser, and remove the contents.

?Wash the inside surfaces with a warm water and baking soda solution. The solution should be about 2 tablespoons of baking soda to a quart of water.

?Wash the shelves and metal plate with a mild detergent solution.

?Wring excess water out of the sponge or cloth when cleaning area of the controls, or any electrical parts.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model Number / No. de Modelo La sección en espa ñol empieza en la páginaBeer Dispenser Safety Your safety and the safety of others are very importantImportant Safeguides Registration Information Page Avanti Customer Service Help US Help YOURead this guide carefully Write down the model and serial numbersTable of Contents Arts and Features Important Safety Instructions Installation Instructions? Before Using Your Beer Dispenser ? Installation of Your Beer Dispenser?Warning? ? Electrical Connection? Extension Cord ? Reversing the Door Swing of Your ApplianceBeer Keg Installation Sketch ? Installation Instructions for Beer DispenserCO2 GAS can be Dangerous Castors with Lock Installation Sketch Installation of CO2 Cylinder HolderInstallation of CO2 Cylinder Installation of CO2 RegulatorInstallation Of t he Keg Coupler Installation of the CO2 Air Line HoseInstallation of Protective Metal Plate Installation of the Beer KegInstallation of CO2 Air Line Hose t o Re gulator Installation Of The Beer TowerConnecting the Beer Tower to Coupler How to Tap a Keg of BeerAdjusting the CO2 Regulator ? Spanner Faucet Wrench? Plastic Faucet Lever ? Dispensing BeerCare and Maintenance Operating Your Beer DispenserDraught Beer Trouble Guide Cloudy Beer? Vacation Time ? Moving Your Beer DispenserFlat Beer Loose Foam OFF-TASTE BeerSour Beer Wild BeerPage Tail END Beer Troubleshooting Guide Problems with Your Beer DISPENSER?Service for Your Beer Dispenser Avanti Products Customer ServicesLimited Second Through Fifth Year Warranty What is Covered Limited ONE-YEAR WarrantyWhat is not Covered Wiring Diagram Precaución Instrucciones EN EspañolInstrucciones Para LA Instalacion ? Conexión eléctrica AdvertenciaInstalación del Soporte del Cilindro de CO2 GAS Carbonico Instalación del Cilindro de CO2 GAS CarbonicoInstalación del Regulador de CO2 GAS Carbonico Instalación de la torre al acopladorInstalación del adaptador del barril Instalación de la manguera de aire CO2 GAS CarbonicoComo servir la cerveza desde la Torre Como abrir la válvula principal del CO2 GAS CarbonicoUsando SU Dispensador DE Cerveza ? Control de temperatura? Descongelamiento Automático Cuidado Y Mantenimiento? Limpieza de su Dispensador de Cerveza ? Si usted sale de vacaciones? Para mover su dispensador Cerveza TurbiaCerveza Acida Cerveza SIN CuerpoPerdida DE Espuma Cerveza SIN SaborCerveza Rebelde Problemas CON SU Dispensador DE Cerveza Guia Para Solucionar Problemas

BD6000 specifications

The Avanti BD6000 is a state-of-the-art electric bike designed for enthusiasts who seek adventure without compromising on comfort and performance. This model stands out in the crowded e-bike market due to its unique blend of cutting-edge technology, stylish design, and practical features.

One of the most impressive aspects of the Avanti BD6000 is its powerful electric motor. Equipped with a high-torque 750W motor, the BD6000 offers a swift and responsive ride. This motor enables the bike to tackle steep hills and challenging terrains with ease, ensuring that riders can conquer any route they choose. The bike's top speed can reach up to 28 mph, which makes it a great option for both commuting and recreational outings.

Another notable feature is the advanced battery system. The Avanti BD6000 incorporates a removable lithium-ion battery with a capacity of 48V and 14Ah, providing a remarkable range of up to 50 miles on a single charge. This extended range is particularly beneficial for longer rides, allowing users to travel further without worrying about running out of power. The battery also features smart charging technology, ensuring quick charging times and longevity.

The bike's frame is designed with both durability and aesthetics in mind. Constructed from lightweight aluminum alloy, the BD6000 is robust yet easy to maneuver. The design incorporates a sleek, modern appearance that appeals to a variety of riders, whether they're high-performance cyclists or casual weekend riders.

Furthermore, the Avanti BD6000 comes equipped with top-of-the-line components. It features a Shimano gear system that allows for smooth and precise shifting, enhancing the overall riding experience. The bike is equipped with hydraulic disc brakes for reliable stopping power in a variety of conditions, ensuring safety at all times.

For comfort, the Avanti BD6000 includes an adjustable seat and ergonomic handlebars, allowing riders to customize their posture for a more enjoyable ride. Additionally, the bike is fitted with puncture-resistant tires that provide excellent traction and stability on various surfaces.

In summary, the Avanti BD6000 represents an innovative approach to electric biking, merging performance, range, and comfort in a stylish package. With its robust motor, long-lasting battery, and high-quality components, this e-bike is designed to meet the needs of diverse riders, making it an outstanding choice for an electrically-assisted cycling experience. Whether navigating city streets or exploring off-road paths, the Avanti BD6000 promises an exhilarating and reliable ride.
Top Page Image Contents