Lincoln 1200, 1400, 1000 service manual GAS Valve Replacement and Adjustments

Page 55

THE FOLLOWING ITEMS ARE USED IN THE MODEL 1030, 1046, 1047 IMPINGER OVEN (EXPORT)

AIR PRESSURE SWITCHES - REPLACEMENT AND ADJUSTMENT

1.Remove control panel top.

2.Disconnect wires from switch making note of wire number and location for reinstallation.

3.Remove air tube from switch assembly.

4.Remove switch from wire hanger.

5.Install new switch in reverse order, make sure air tube is not blocked miss-aligned. Adjust as needed.

To adjust the air pressure switch, remove snap on cover on the side of the switch to expose adjusting screw. To increase sensitivity, turn screw counter clockwise; to decrease sensitivity, turn screw clockwise. Check for proper line voltage switching from N.C. to N.O. as the air pressure switch closes.

GAS VALVE - REPLACEMENT AND ADJUSTMENTS

1.Remove control panel top and front cover.

2.Disconnect the gas piping from the back of the unit.

3.Remove the four (4) screws from the incoming nipple mounting bracket.

4.Remove incoming nipple.

5.Disconnect two (2) plugs, (1 ) 3 prong and (1 ) 4 prong - Note location.

6.Disconnect pipe union just above gas valve and remove assembly.

7.Reassemble in reverse order (check all pipe fittings for leaks). After assembled, check for proper adjustment of gas pressure switch, 8.8 on dial for natural gas, 23 for L.P. Gas and 4.5 for town gas.

8.Check and adjust manifold pressure. Remove pressure tap located in gas piping above the gas valve prior to the burner orifice and install manometer . Adjustment screw is located on the front of the valve, remove plastic cap and adjust as needed: 3.5" W.C. for Natural Gas and 10" W.C. for L.P.

9.Check gas filter by removing cover plate (located on either side of valve). Remove four

(4) screws and slide filter out of valve housing and inspect. Reassemble in reverse order and check for leaks around cover.

SIDE VIEW

FILTER

COVER

PLATE

PRESSURE CONTROLLER ADJUSTMENT

FILTER

COVER

PLATE

 

TOP VIEW

 

 

 

 

 

OUTPUT

 

 

 

MANIFOLD

 

 

 

PRESSURE

 

 

 

ADJUSTMENT

 

+

 

 

 

 

gnd

ELECTRICAL

-

1

2

CONNECTOR

 

 

 

3

 

 

3

 

 

2

 

 

ELECTRICAL

 

 

 

 

gnd

 

CONNECTOR

Impinger I -–1000 Series Service Manual - Domestic

55

Image 55
Contents Impinger Conveyor Ovens Table of Contents Control BOX Auto Power SupplyModel 1200 120/230 VAC 60HZ Natural GAS/DUAL Belt Model 1204 120/230 VAC 60HZ Natural GAS/DUAL BeltControl TemperatureTime Temp Display Heat CircuitTIME/TEMP Display Conveyor DriveModel 1240 120/230 VAC 60HZ Natural GAS/DUAL Belt TIME/TEMP Time Temp Display Schematic / 1000 Schematic / 1004 Schematic / 1022, 1023 S/N Q19077 & below Schematic / 1022, 1023 S/N Q19078 & Above Schematic / 1040, 1041 S/N Q14279 & below Schematic / 1040, 1041 S/N Q14280 & Above Schematic / 1200 Schematic / 1202, 1203 S/N Q14790 & below Schematic / 1202, 1203 S/N Q14791 & Above Schematic / 1204 Schematic / 1240, 1241 S/N Q14279 & below Schematic / 1240, 1241 S/N Q14280 & Above Symptom Possible Cause Evaluation Troubleshooting Guide 1000GAS Ovens Honeywell Ignition For ovens withJohnson Controls Ignition ControlControl Code Page Electric Ovens Model Series 1000 Troubleshooting GuidePage Page Page Page Page Page FAN, Main REMOVAL, Installation & AdjustmentsMOTOR, Main FAN CAPACITOR, MotorRELAY, D.P.S.T Cool Down SwitchAbove GAS Above Electric FAN Spider FAN HUB ConeBurner Blower Motor THERMOSTAT, Cooling FANAIR Pressure Switch To Remove the Blower Wheel for Periodic CleaningBlower WHEEL, Burner Manifold PRESSURE-ADJUSTMENT Burner AssemblyGAS Control Valve Solenoid Valve Manifold Pressure AdjustmentTemperature Control Valve Robert Shaw Temperature Control BoardMercury Contactor Temperature Control Potentiometer ReplacementTHERMOCOUPLE- Replacement Thermocouple Measurement ChartIgnition Control Heating Element24V GND Burner Light 24 VAC GAS Ovens Flame SensorBurner Ignitor Transformer 120/24 VACPotentiometer Conveyor Speed Control Conveyor Motor Replacement Bodine SNPilot Orifice Burner Main Orifice BurnerSeries SN 4390 Conveyor Motor Replacement Baldor 1000 Series SN 4390Coupling and Encoder Disc Motor Control Board Calibration Optical Encoder AssemblyTACH. Generator Conveyor Motor Control BoardREG MIN MAX Style Style 1 Control Board AdjustmentStyle 2 and Style 3 Control Board Adjustment Motor Control BoardStyle DIP Switches Control Switch Position OFF Drive END Reversing Conveyor DirectionMini Circuit Breaker BEARING, ConveyorOLD Style Hall Effect Sensor ReplacementBEARING, Conveyor SN 2164 and Above TRANSFORMER-STEPPER Motor ControlTRANSFORMER, TIME/TEMP. Display Temperature Gauge ReplacementThermistor Replacement Oven TemperatureALL 1000 & 1200 Series Ovens Switch SettingsType OFF Bottom of Time Temp Display SWITCH, DISPLAY, SETSwitch Replacement FAN, HEAT, Conveyor Dip SwitchSwitch Replacement FAN Switch Update GAS Valve Replacement and Adjustments Solenoid Valve Replacement Ignition Control ReplacementHigh Limit Thermostat Replacement Spark Generator ReplacementBurner Blower Motor Replacement Burner Alarm Light ReplacementPilot Light 220V Replacement Igniter Sensor Assembly ReplacementTime Delay RELAY, 20 Minute Replacement Relay ASSEMBLY, Burner Blower Motor ReplacementTemperature Control Replacement RELAY, GAS Control Replacement Model 1046,1047This page Intentionally Left Blank Letter Description Parts / Model Series 1000 & 1200 GeneralBlow UP / 1000, 1200 General Parts / Access Door & 1050 Door Blow UP / Access Door & 1050 Door Parts / Model 1000,1001,1050,1051,1004, &1005 S/N 100 to Blow UP / 1000, 1001, 1050, 1051, 1004, & 1005 S/N 100 to Parts / Model 1000,1001,1004, and 1005 S/N 4390 & Above Blow UP 1000, 1001, 1004, 1005 S/N 4390 & Above Parts Blow UP / 1022 Tooth Sprocket S/N 4390 to Q14973 Blow UP / 1040 Parts / 1200, 1201, 1204 Blow UP / 1200, 1201, 1204 Parts Blow UP / 1202 Electronic Temperature Control Blow UP / 1240 Parts / Oven Back GAS Blow UP / Oven Back GAS Parts / Oven BACK- Electric Blow UP / Oven Back Electric Parts / Conveyor Motor Assembly S/N 4390 & Above Blow UP / Conveyor Motor Assembly S/N 4390 & Above Parts / Series 1000 Conveyor Blow UP / Series 1000 Conveyor See Parts / Series 1200 Conveyor ControlBlow UP / Series 1200 Conveyor Control Parts / Series 1200 Conveyor Blow UP / Series 1200 Conveyor This page intentionally left blank This page intentionally left blank
Related manuals
Manual 20 pages 1.12 Kb Manual 92 pages 1.67 Kb

1000, 1200, 1400 specifications

The Lincoln series, particularly the models Lincoln 1000, 1200, and 1400, represents an evolution in luxury vehicles, combining elegance with cutting-edge technology. Each model builds upon its predecessor while introducing features that enhance performance, comfort, and safety.

Starting with the Lincoln 1000, this model set the foundation for the series. It showcased a refined design characterized by sleek lines and an impressive presence on the road. The Lincoln 1000 was equipped with a powerful engine, delivering smooth acceleration and a quiet ride. Interior features included premium materials such as leather upholstery, real wood accents, and a state-of-the-art sound system. Additionally, it offered advanced climate control systems, ensuring passenger comfort. Safety features were also prioritized, with multiple airbags and stability control systems included to enhance driver confidence.

Moving on to the Lincoln 1200, this model took luxury to the next level. The exterior design was more aggressive, with a revised grille and enhanced aerodynamics for better fuel efficiency. The engine options expanded, offering hybrid technology for environmentally conscious consumers without sacrificing power. Inside, the Lincoln 1200 featured an upgraded infotainment system, incorporating a larger touchscreen display along with smartphone integration for connectivity on the go. This model also introduced adaptive cruise control and lane-keeping assist, showcasing Lincoln’s commitment to safety and innovation.

The Lincoln 1400 represents the pinnacle of this series. This model incorporates all the advancements of the previous iterations while introducing next-generation technologies. A hybrid powertrain with electric capabilities provides a quieter, more efficient drive. The design includes sophisticated lighting technology, such as adaptive LED headlights that adjust to road conditions. Inside, the cabin has been transformed into a haven of luxury, with customizable ambient lighting, heated and ventilated seats, and an advanced noise cancellation system for a serene driving experience. Furthermore, the Lincoln 1400 emphasizes driver assistance technology, featuring an array of sensors and cameras to support features like automatic parking and enhanced collision prevention systems.

In conclusion, the Lincoln 1000, 1200, and 1400 models showcase a remarkable journey of luxury and technology, with each iteration bringing forth innovative features and design enhancements that elevate the driving experience. As Lincoln continues to evolve, the commitment to craftsmanship, comfort, and cutting-edge technology remains central to its identity.