Lincoln 1200 Manifold Pressure Adjustment, Temperature Control Valve Robert Shaw, Solenoid Valve

Page 37

MANIFOLD PRESSURE - ADJUSTMENT

1.Remove control panel top and front cover.

2.WITH ELECTRIC POWER AND GAS OFF: remove the outlet pressure tap plug from the gas control valve and install the adapter fitting and manometer.

3.Turn on electric power and gas and start-up oven.

4.With oven at full fire, manifold pressure should be (3.5"W.C. NAT/10" W.C. LP).

5.Turn off electric power and gas, replace cover screw, remove manometer and adapter; replace pressure tap plug.

6.Check pressure tap for gas leaks before closing panel.

7.Close control panel and check system operation.

TEMPERATURE CONTROL VALVE (ROBERT SHAW)

1.Shut off power at main breaker

2.Shut off gas supply.

3.Remove control panel top and front cover.

4.Remove gas control valve (See Above).

5.Remove the two-(2) 3/8" x 16 nuts that hold main orifice bracket to the burner assembly.

6.Remove temperature control valve sensing bulb from oven cavity.

NOTE: It may be necessary to remove conveyor and fingers from oven cavity.

7.Remove piping from old temperature control valve.

8.Reassemble in reverse order, be sure the sensing bulb is properly placed in the oven cavity. The sensing bulb is properly placed in the oven cavity when it is placed in

the spring holder and positioned with the 5 1/2" of the bulb to the left of the spring holder. NOTE: The bypass screw should be adjusted all the way in.

SOLENOID VALVE

1.Shut off power at main breaker.

2.Shut off gas supply.

3.Remove control panel top and front cover.

4.Remove gas control valve (See "GAS CONTROL VALVE").

5.Disconnect wires from solenoid valve.

6.Remove two (2) 3/8" x 16 hex nuts that hold main orifice bracket in place.

7.Remove solenoid valve assembly.

8.Remove piping from solenoid valve.

9.Reassemble in reverse order.

TEMPERATURE CONTROL BOARD

GAS OVENS

1.Shut off power at main breaker.

2.Remove control panel top and front cover.

3.Remove relay box cover.

4.Disconnect wiring from temperature control board.

5.Make note of wire number and location for reinstallation.

6.Reassemble in reverse order.

ELECTRIC OVENS

1.Shut off power at main breaker.

2.Remove control panel top and front cover.

3.Disconnect wiring from temperature control board.

4.Make note of wire numbers and location for reinstallation.

5.Reassemble in reverse order.

Impinger I -–1000 Series Service Manual - Domestic

37

Image 37
Contents Impinger Conveyor Ovens Table of Contents Model 1200 120/230 VAC 60HZ Natural GAS/DUAL Belt Power SupplyModel 1204 120/230 VAC 60HZ Natural GAS/DUAL Belt Control BOX AutoTime Temp Display TemperatureHeat Circuit ControlTIME/TEMP Display Conveyor DriveModel 1240 120/230 VAC 60HZ Natural GAS/DUAL Belt TIME/TEMP Time Temp Display Schematic / 1000 Schematic / 1004 Schematic / 1022, 1023 S/N Q19077 & below Schematic / 1022, 1023 S/N Q19078 & Above Schematic / 1040, 1041 S/N Q14279 & below Schematic / 1040, 1041 S/N Q14280 & Above Schematic / 1200 Schematic / 1202, 1203 S/N Q14790 & below Schematic / 1202, 1203 S/N Q14791 & Above Schematic / 1204 Schematic / 1240, 1241 S/N Q14279 & below Schematic / 1240, 1241 S/N Q14280 & Above Symptom Possible Cause Evaluation Troubleshooting Guide 1000GAS Ovens Johnson Controls For ovens withIgnition Control Honeywell IgnitionControl Code Page Electric Ovens Model Series 1000 Troubleshooting GuidePage Page Page Page Page Page MOTOR, Main FAN REMOVAL, Installation & AdjustmentsCAPACITOR, Motor FAN, MainAbove GAS Above Electric Cool Down SwitchFAN Spider FAN HUB Cone RELAY, D.P.S.TBurner Blower Motor THERMOSTAT, Cooling FANAIR Pressure Switch To Remove the Blower Wheel for Periodic CleaningBlower WHEEL, Burner Manifold PRESSURE-ADJUSTMENT Burner AssemblyGAS Control Valve Temperature Control Valve Robert Shaw Manifold Pressure AdjustmentTemperature Control Board Solenoid ValveTHERMOCOUPLE- Replacement Temperature Control Potentiometer ReplacementThermocouple Measurement Chart Mercury ContactorIgnition Control Heating Element24V GND Burner Ignitor Flame SensorTransformer 120/24 VAC Burner Light 24 VAC GAS OvensPilot Orifice Burner Conveyor Motor Replacement Bodine SNMain Orifice Burner Potentiometer Conveyor Speed ControlSeries SN 4390 Conveyor Motor Replacement Baldor 1000 Series SN 4390Coupling and Encoder Disc TACH. Generator Optical Encoder AssemblyConveyor Motor Control Board Motor Control Board CalibrationREG MIN MAX Style 2 and Style 3 Control Board Adjustment Style 1 Control Board AdjustmentMotor Control Board StyleStyle DIP Switches Control Switch Position OFF Mini Circuit Breaker Reversing Conveyor DirectionBEARING, Conveyor Drive ENDBEARING, Conveyor SN 2164 and Above Hall Effect Sensor ReplacementTRANSFORMER-STEPPER Motor Control OLD StyleThermistor Replacement Temperature Gauge ReplacementOven Temperature TRANSFORMER, TIME/TEMP. DisplayALL 1000 & 1200 Series Ovens Switch SettingsType OFF Bottom of Time Temp Display SWITCH, DISPLAY, SETSwitch Replacement FAN, HEAT, Conveyor Dip SwitchSwitch Replacement FAN Switch Update GAS Valve Replacement and Adjustments High Limit Thermostat Replacement Ignition Control ReplacementSpark Generator Replacement Solenoid Valve ReplacementPilot Light 220V Replacement Burner Alarm Light ReplacementIgniter Sensor Assembly Replacement Burner Blower Motor ReplacementTemperature Control Replacement Relay ASSEMBLY, Burner Blower Motor ReplacementRELAY, GAS Control Replacement Model 1046,1047 Time Delay RELAY, 20 Minute ReplacementThis page Intentionally Left Blank Letter Description Parts / Model Series 1000 & 1200 GeneralBlow UP / 1000, 1200 General Parts / Access Door & 1050 Door Blow UP / Access Door & 1050 Door Parts / Model 1000,1001,1050,1051,1004, &1005 S/N 100 to Blow UP / 1000, 1001, 1050, 1051, 1004, & 1005 S/N 100 to Parts / Model 1000,1001,1004, and 1005 S/N 4390 & Above Blow UP 1000, 1001, 1004, 1005 S/N 4390 & Above Parts Blow UP / 1022 Tooth Sprocket S/N 4390 to Q14973 Blow UP / 1040 Parts / 1200, 1201, 1204 Blow UP / 1200, 1201, 1204 Parts Blow UP / 1202 Electronic Temperature Control Blow UP / 1240 Parts / Oven Back GAS Blow UP / Oven Back GAS Parts / Oven BACK- Electric Blow UP / Oven Back Electric Parts / Conveyor Motor Assembly S/N 4390 & Above Blow UP / Conveyor Motor Assembly S/N 4390 & Above Parts / Series 1000 Conveyor Blow UP / Series 1000 Conveyor See Parts / Series 1200 Conveyor ControlBlow UP / Series 1200 Conveyor Control Parts / Series 1200 Conveyor Blow UP / Series 1200 Conveyor This page intentionally left blank This page intentionally left blank
Related manuals
Manual 20 pages 1.12 Kb Manual 92 pages 1.67 Kb

1000, 1200, 1400 specifications

The Lincoln series, particularly the models Lincoln 1000, 1200, and 1400, represents an evolution in luxury vehicles, combining elegance with cutting-edge technology. Each model builds upon its predecessor while introducing features that enhance performance, comfort, and safety.

Starting with the Lincoln 1000, this model set the foundation for the series. It showcased a refined design characterized by sleek lines and an impressive presence on the road. The Lincoln 1000 was equipped with a powerful engine, delivering smooth acceleration and a quiet ride. Interior features included premium materials such as leather upholstery, real wood accents, and a state-of-the-art sound system. Additionally, it offered advanced climate control systems, ensuring passenger comfort. Safety features were also prioritized, with multiple airbags and stability control systems included to enhance driver confidence.

Moving on to the Lincoln 1200, this model took luxury to the next level. The exterior design was more aggressive, with a revised grille and enhanced aerodynamics for better fuel efficiency. The engine options expanded, offering hybrid technology for environmentally conscious consumers without sacrificing power. Inside, the Lincoln 1200 featured an upgraded infotainment system, incorporating a larger touchscreen display along with smartphone integration for connectivity on the go. This model also introduced adaptive cruise control and lane-keeping assist, showcasing Lincoln’s commitment to safety and innovation.

The Lincoln 1400 represents the pinnacle of this series. This model incorporates all the advancements of the previous iterations while introducing next-generation technologies. A hybrid powertrain with electric capabilities provides a quieter, more efficient drive. The design includes sophisticated lighting technology, such as adaptive LED headlights that adjust to road conditions. Inside, the cabin has been transformed into a haven of luxury, with customizable ambient lighting, heated and ventilated seats, and an advanced noise cancellation system for a serene driving experience. Furthermore, the Lincoln 1400 emphasizes driver assistance technology, featuring an array of sensors and cameras to support features like automatic parking and enhanced collision prevention systems.

In conclusion, the Lincoln 1000, 1200, and 1400 models showcase a remarkable journey of luxury and technology, with each iteration bringing forth innovative features and design enhancements that elevate the driving experience. As Lincoln continues to evolve, the commitment to craftsmanship, comfort, and cutting-edge technology remains central to its identity.