Lincoln 1400, 1200, 1000 service manual Burner Alarm Light Replacement, Pilot Light 220V Replacement

Page 57

BURNER ALARM LIGHT - REPLACEMENT

1.Remove control panel top and front cover.

2.Remove two (2) wires from light assembly, note wire number and location.

3.Grasp body of light assembly and slide sideways to remove.

4.Reassemble in reverse order and check.

PILOT LIGHT (220V) - REPLACEMENT

1.Remove control panel top and front cover.

2.Remove switch access cover.

3.Remove two (2) wires from light assembly, note wire number and location.

4.Grasp body of light assembly and slide sideways to remove.

5.Reassemble in reverse order and check.

IGNITER SENSOR ASSEMBLY - REPLACEMENT

1.Remove control panel top and front cover.

2.Remove gas valve assembly (See Gas Valve)

3.Remove screws from burner tube and pull burner assembly out.

4.Remove wire connectors from igniter sensor assembly.

5.Remove screws from mounting bracket and remove assembly.

6.Reassemble in reverse order and check system operation. NOTE: After installation, check all pipe fittings for leaks.

BURNER BLOWER MOTOR – REPLACEMENT

1.Remove control panel top and front cover.

2.Remove screws around blower tube.

3.Disconnect motor wiring and remove.

4.Reassemble in reverse order and check system operation.

TEMPERATURE CONTROL BOARD - REPLACEMENT- MODEL 1030

1.Remove control panel top and front cover.

2.Remove potentiometer leads (3), note color and location.

3.Remove thermocouple leads (2), note color and location (white:pos/red:neg.).

4.Remove power and solenoid leads (4), note wire number and location.

5.Remove screw and board assembly and replace.

6.Reassemble in reverse order and check system operation.

NOTE: When replacing #369174 with (new) #369728, turn temperature control to its maximum position and allow oven 30 minute preheat then calibrate board as follows:

Place temperature probe between top fingers #2 and #3 (making sure probe is not touching any metal) and adjust potentiometer P6 to a Maximum temperature of 575°F.

RED

 

POTENTIOMETER

 

 

2.5 K OHMS

BLACK

1

P 6

P 5

2

 

 

 

WHITE

3

 

11

 

 

+

 

 

10

6

P 3

9

-

7

 

 

 

 

 

 

THERMOCOUPLE

 

 

 

TYPE J

 

 

 

transformer marked with green gold or silver dot

L 1 120 VAC

L2

LOAD

Impinger I -–1000 Series Service Manual - Domestic

57

Image 57
Contents Impinger Conveyor Ovens Table of Contents Model 1200 120/230 VAC 60HZ Natural GAS/DUAL Belt Power SupplyModel 1204 120/230 VAC 60HZ Natural GAS/DUAL Belt Control BOX AutoTime Temp Display TemperatureHeat Circuit ControlConveyor Drive TIME/TEMP DisplayModel 1240 120/230 VAC 60HZ Natural GAS/DUAL Belt TIME/TEMP Time Temp Display Schematic / 1000 Schematic / 1004 Schematic / 1022, 1023 S/N Q19077 & below Schematic / 1022, 1023 S/N Q19078 & Above Schematic / 1040, 1041 S/N Q14279 & below Schematic / 1040, 1041 S/N Q14280 & Above Schematic / 1200 Schematic / 1202, 1203 S/N Q14790 & below Schematic / 1202, 1203 S/N Q14791 & Above Schematic / 1204 Schematic / 1240, 1241 S/N Q14279 & below Schematic / 1240, 1241 S/N Q14280 & Above Troubleshooting Guide 1000 Symptom Possible Cause EvaluationGAS Ovens Johnson Controls For ovens withIgnition Control Honeywell IgnitionControl Code Page Electric Ovens Model Series 1000 Troubleshooting GuidePage Page Page Page Page Page MOTOR, Main FAN REMOVAL, Installation & AdjustmentsCAPACITOR, Motor FAN, MainAbove GAS Above Electric Cool Down SwitchFAN Spider FAN HUB Cone RELAY, D.P.S.TBurner Blower Motor THERMOSTAT, Cooling FANTo Remove the Blower Wheel for Periodic Cleaning AIR Pressure SwitchBlower WHEEL, Burner Burner Assembly Manifold PRESSURE-ADJUSTMENTGAS Control Valve Temperature Control Valve Robert Shaw Manifold Pressure AdjustmentTemperature Control Board Solenoid ValveTHERMOCOUPLE- Replacement Temperature Control Potentiometer ReplacementThermocouple Measurement Chart Mercury ContactorIgnition Control Heating Element24V GND Burner Ignitor Flame SensorTransformer 120/24 VAC Burner Light 24 VAC GAS OvensPilot Orifice Burner Conveyor Motor Replacement Bodine SNMain Orifice Burner Potentiometer Conveyor Speed ControlConveyor Motor Replacement Baldor 1000 Series SN 4390 Series SN 4390Coupling and Encoder Disc TACH. Generator Optical Encoder AssemblyConveyor Motor Control Board Motor Control Board CalibrationREG MIN MAX Style 2 and Style 3 Control Board Adjustment Style 1 Control Board AdjustmentMotor Control Board StyleStyle DIP Switches Control Switch Position OFF Mini Circuit Breaker Reversing Conveyor DirectionBEARING, Conveyor Drive ENDBEARING, Conveyor SN 2164 and Above Hall Effect Sensor ReplacementTRANSFORMER-STEPPER Motor Control OLD StyleThermistor Replacement Temperature Gauge ReplacementOven Temperature TRANSFORMER, TIME/TEMP. DisplaySwitch Settings ALL 1000 & 1200 Series OvensType OFF Bottom of Time Temp Display SWITCH, DISPLAY, SETDip Switch Switch Replacement FAN, HEAT, ConveyorSwitch Replacement FAN Switch Update GAS Valve Replacement and Adjustments High Limit Thermostat Replacement Ignition Control ReplacementSpark Generator Replacement Solenoid Valve ReplacementPilot Light 220V Replacement Burner Alarm Light ReplacementIgniter Sensor Assembly Replacement Burner Blower Motor ReplacementTemperature Control Replacement Relay ASSEMBLY, Burner Blower Motor ReplacementRELAY, GAS Control Replacement Model 1046,1047 Time Delay RELAY, 20 Minute ReplacementThis page Intentionally Left Blank Letter Description Parts / Model Series 1000 & 1200 GeneralBlow UP / 1000, 1200 General Parts / Access Door & 1050 Door Blow UP / Access Door & 1050 Door Parts / Model 1000,1001,1050,1051,1004, &1005 S/N 100 to Blow UP / 1000, 1001, 1050, 1051, 1004, & 1005 S/N 100 to Parts / Model 1000,1001,1004, and 1005 S/N 4390 & Above Blow UP 1000, 1001, 1004, 1005 S/N 4390 & Above Parts Blow UP / 1022 Tooth Sprocket S/N 4390 to Q14973 Blow UP / 1040 Parts / 1200, 1201, 1204 Blow UP / 1200, 1201, 1204 Parts Blow UP / 1202 Electronic Temperature Control Blow UP / 1240 Parts / Oven Back GAS Blow UP / Oven Back GAS Parts / Oven BACK- Electric Blow UP / Oven Back Electric Parts / Conveyor Motor Assembly S/N 4390 & Above Blow UP / Conveyor Motor Assembly S/N 4390 & Above Parts / Series 1000 Conveyor Blow UP / Series 1000 Conveyor See Parts / Series 1200 Conveyor ControlBlow UP / Series 1200 Conveyor Control Parts / Series 1200 Conveyor Blow UP / Series 1200 Conveyor This page intentionally left blank This page intentionally left blank
Related manuals
Manual 20 pages 1.12 Kb Manual 92 pages 1.67 Kb

1000, 1200, 1400 specifications

The Lincoln series, particularly the models Lincoln 1000, 1200, and 1400, represents an evolution in luxury vehicles, combining elegance with cutting-edge technology. Each model builds upon its predecessor while introducing features that enhance performance, comfort, and safety.

Starting with the Lincoln 1000, this model set the foundation for the series. It showcased a refined design characterized by sleek lines and an impressive presence on the road. The Lincoln 1000 was equipped with a powerful engine, delivering smooth acceleration and a quiet ride. Interior features included premium materials such as leather upholstery, real wood accents, and a state-of-the-art sound system. Additionally, it offered advanced climate control systems, ensuring passenger comfort. Safety features were also prioritized, with multiple airbags and stability control systems included to enhance driver confidence.

Moving on to the Lincoln 1200, this model took luxury to the next level. The exterior design was more aggressive, with a revised grille and enhanced aerodynamics for better fuel efficiency. The engine options expanded, offering hybrid technology for environmentally conscious consumers without sacrificing power. Inside, the Lincoln 1200 featured an upgraded infotainment system, incorporating a larger touchscreen display along with smartphone integration for connectivity on the go. This model also introduced adaptive cruise control and lane-keeping assist, showcasing Lincoln’s commitment to safety and innovation.

The Lincoln 1400 represents the pinnacle of this series. This model incorporates all the advancements of the previous iterations while introducing next-generation technologies. A hybrid powertrain with electric capabilities provides a quieter, more efficient drive. The design includes sophisticated lighting technology, such as adaptive LED headlights that adjust to road conditions. Inside, the cabin has been transformed into a haven of luxury, with customizable ambient lighting, heated and ventilated seats, and an advanced noise cancellation system for a serene driving experience. Furthermore, the Lincoln 1400 emphasizes driver assistance technology, featuring an array of sensors and cameras to support features like automatic parking and enhanced collision prevention systems.

In conclusion, the Lincoln 1000, 1200, and 1400 models showcase a remarkable journey of luxury and technology, with each iteration bringing forth innovative features and design enhancements that elevate the driving experience. As Lincoln continues to evolve, the commitment to craftsmanship, comfort, and cutting-edge technology remains central to its identity.