Maytag MDB6709AWW Drain Requirements, Water Supply Requirements, Electrical Requirements

Page 5

Drain Requirements

•A new drain hose is supplied with your dishwasher.

If the drain hose is not long enough, use a new drain hose with a maximum length of 12’ (3.7 m) (Part Number 3385556) that meets all current AHAM/IAPMO test standards, is resistant to heat and detergent, and fits the 1" (2.5 cm) drain connector of the dishwasher.

•Make sure to connect drain hose to waste tee or disposer inlet above drain trap in house plumbing and 20" (50.8 cm) minimum above the floor. It is recommended that the drain hose either be looped up and securely fastened to the underside of the counter, or be connected to an air gap.

•Make sure to use an air gap if the drain hose is connected to house plumbing lower than 20" (50.8 cm) above subfloor or floor.

Use of air gap

Air gap

•Use ¹⁄₂" minimum I.D. drain line fittings.

•If required, the air gap should be installed in accordance

with the air gap installation instructions. When connecting the air gap, a rubber hose (not provided) will be needed to connect to the waste tee or disposer inlet.

Water Supply Requirements

•A hot water line with 20-120 psi (138-862 kPa) water pressure can be verified by a licensed plumber.

•120°F (49°C) water at dishwasher.

•³⁄₈" O.D. copper tubing with compression fitting or

flexible braided water supply line (Part Number 4396897RP) NOTE: ¹⁄₂" minimum plastic tubing is not recommended.

•A 90° elbow with ³⁄₈" N.P.T. external pipe threads on one end.

•Do not solder within 6" (15.2 cm) of the water inlet valve.

Electrical Requirements

Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/NFPA 70 - latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from: National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169

You must have:

•120-volt, 60 Hz, AC-only, 15- or 20- amp, fused electrical supply.

•copper wire only.

We recommend:

•a time-delay fuse or circuit breaker.

•a separate circuit.

If connecting dishwasher with a power supply cord:

•Use UL listed power supply cord kit (Part Number 4317824) marked for use with dishwasher.

•Power supply cord must plug into

a grounded 3 prong outlet, located in the cabinet next to the dishwasher opening. Outlet must meet all local codes and ordinances.

If connecting dishwasher with direct wiring:

•Use flexible, armored or nonmetallic sheathed,

copper wire with grounding wire that meets

the wiring requirements for your home and local codes and ordinances.

• Use a UL Listed/CSA Approved strain relief.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Table of Contents Table des matières W10290309A You Need to Table of ContentsLocation Requirements Tools and PartsMinimum, measured from narrowest point of opening Product and Cabinet Opening DimensionsWater Supply Requirements Drain RequirementsElectrical Requirements Use of air gapPrepare Cabinet Opening-New Utilities Prepare Cabinet Opening-Existing UtilitiesPrepare and Route Water Line Install Drain Hose Waste disposer with air gap Connect drain hoseWaste disposer no air gap No waste disposer no air gapPrepare Dishwasher Power Cord-Route cord into terminal box Make Power Supply Cord ConnectionPower Supply Cord- Connect ground wire Power Cord-Connect remaining wiresDetermine Cabinet Opening Choose Attachment Option Install the Door Handle on some modelsMove Dishwasher into Cabinet Opening Connect to Water Supply Slide clamp onto connector Make Direct Wire Electrical ConnectionDirect Wire-Route cable into terminal box Connect to DrainDirect Wire-Connect remaining wires Direct Wire-Connect ground wireDirect Wire-Secure cable in conduit connector Direct Wire-Reinstall terminal box coverSecure Dishwasher in Cabinet Opening Reinstall access panels Complete InstallationRemove towel and replace lower dishwasher rack Check lower panel edgeReconnect power Power supply cord-Plug into a grounded 3 prong outletCheck Operation If Dishwasher Does Not OperateTable des matières Instructions d’installation suiteProcessus à appliquer Préparation de la cavité dencastrementOutillage et pièces Exigences d’emplacementMinimum à l’endroit le plus étroit de la cavité Dimensions Produit et cavité d’encastrementEn gris sur les parois de la cavité d’encastrement Spécifications de l’alimentation en eau Spécifications de l’évacuationSpécifications électriques Utilisation d’un brise-videFermer l’arrivée d’eau Déconnecter la source de courant électriqueMoyens de raccordement aux divers circuits déjà existants? Quel type de raccordement électrique sera utilisé?Câblage direct Perçage du trou Cordon d’alimentation Préparation du trouCâblage direct Préparation du trou Câblage direct Acheminement du câbleInstallation de la canalisation dalimentation Installation du tuyau d’évacuationInstallation du tuyau d’évacuation Purge de la canalisation d’eauBroyeur à déchets pas de brise-vide Raccordement du tuyau d’évacuationBroyeur à déchets avec brise-vide Pas de broyeur à déchets pas de brise-videDépose des panneaux Préparation du lave-vaisselleAttachez l’isolation Raccordement électrique Cordon d’alimentation Installation du serre-câbleÔter le couvercle du boîtier De connexion électrique Cordon d’alimentation Conducteur de liaison à la terreConfiguration de câblage Dimensions de la cavité d’encastrementMesure des dimensions Tableau de réglage Hauteur du lave-vaisselleChoix de l’option de fixation Installation de la poignée de porte sur certains modèlesDéplacement du lave-vaisselle à proximité de louverture Installer le bouton en plastiqueLigne en pointillés Plier la languette montage latéralInsertion du lave-vaisselle dans la cavité d’encastrement La tension des ressortsContrôle de l’aplomb et réglage des pieds si nécessaire IsolantRaccordement à l’égout Raccordement à la canalisation d’eauRaccorder le raccord coudé de 90 à la valve Recherche de fuitesBride de tuyau position finale Raccordement électrique Câblage directCâblage direct Acheminement jusqu’au boîtier de connexion Câblage direct Raccordement des autres conducteursSerrer les vis du serre-câble pour immobiliser le câble Câblage direct Immobilisation dans le connecteur de conduitExtraction du panier inférieur utilisation d’une serviette Achever linstallation Serrage des vis Inspection de la rive de panneau inférieureReconnecter la source de courant électrique Reconnecter la source de courant électriqueSi le lave-vaisselle ne fonctionne pas Contrôle du fonctionnementConseils additionnels W10290309A

MDB6709AWW, W10290309A specifications

The Maytag W10290309A, commonly known as a replacement part for the MDB6709AWW dishwasher series, showcases a blend of reliability and efficiency in home appliances. This specific part is essential for maintaining the performance of the MDB6709AWW model, which is designed with the user in mind, offering innovative technologies and features that streamline dishwashing tasks.

One of the standout features of the MDB6709AWW is its robust construction, which is reflective of Maytag's dedication to durability. Built with high-quality materials, it is designed to handle the rigors of daily use while maintaining its efficiency. This model operates with a powerful motor, ensuring that dishes are not only clean but also sanitized. The performance is enhanced by the Precision Dry option, which ensures that your dishes come out bone-dry, eliminating the need for towel drying.

The MDB6709AWW also includes the power of the Soil Sensor technology. This feature automatically adjusts the wash cycle based on the level of soil detected on the dishes, ensuring optimal water usage and energy efficiency. This smart technology not only saves on utility bills but also contributes to environmental sustainability.

Another characteristic that sets the MDB6709AWW apart is the dedicated rinse aid dispenser. This dispenser effectively helps in preventing spots and film build-up on dishes, ensuring a spotless finish after every wash. The beauty of this feature is that it minimizes the need for manual rinsing before loading, saving precious time.

The ADA-compliant design of the Maytag MDB6709AWW ensures that it is accessible to all users, making it a great choice for families and individuals alike. The intuitive control system allows for easy operation, with clearly labeled options for various wash cycles, temperatures, and settings.

Moreover, the quiet operation of this dishwasher is a noteworthy aspect, making it suitable for open-concept living spaces. With sound dampening technology, this unit operates at minimal noise levels, allowing you to carry on with your daily activities without disruption.

In summary, the Maytag W10290309A and the MDB6709AWW dishwasher embody a combination of advanced technologies, user-focused design, and reliable performance. With features like the Precision Dry, Soil Sensor technology, and a durable build, it's easy to see why this model is trusted in households. Whether you are washing a few items or a full load after a family dinner, this dishwasher promises to deliver outstanding results with every cycle.
Top Page Image Contents