Maytag W10282553A installation instructions Tools and Parts, Location Requirements

Page 3

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the recommended tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

All Installations

Tools needed:

Pliers

Flat-blade

screwdriver

 

Phillips

Utility knife

screwdriver

 

nut drivers or

UL Listed/CSA

Approved twist-on

hex sockets

wire connectors*

Measuring tape

Small level

or ruler

 

10" adjustable wrench

 

that opens to

wrench

 

*Must be the proper size to connect your household wiring to 16 gauge wiring in dishwasher

Other useful items you may need:

Flashlight

Bath towel

Shallow pan

Wood block

Parts supplied:

Drain hose clamps (2)

Drain hose

(1 large and 1 small)

Phillips-head

 

screws (2)

Silver Green

Make sure all these parts are included in the literature package.

Parts needed:

Other parts you may also need:

 

Side mounting kit

Masking or

(38.1– 5 cm)

for solid surface

duct tape

Screw-type

countertops

 

(Part Number

 

clamps (3 maximum)

 

8212560)

 

 

 

NOTE: Parts available for purchase in plumbing supply stores. Check local codes. Check existing electrical supply. See “Electrical Requirements” section. It is recommended that electrical connections be made by a licensed electrical installer.

In addition, for first time installations

Tools needed:

Cordless drill

 

 

with ¹⁄₂", ³⁄₄"

 

 

and 1¹⁄₂" hole

Small

 

saw bits

tubing cutter Wire stripper

Parts needed:

 

 

Copper tubing (³⁄₈"

See “Electrical Requirements” section

O.D. suggested) or

For Direct Wire:

For Power Supply

flexible braided

use UL Listed/

Cord: use UL

water supply line

CSA Approved

listed power

 

 

strain relief

supply cord kit

 

to fit ⁷⁄₈" (2.2 cm)

marked for use

 

hole

with dishwasher

Location Requirements

Grounded electrical supply required.

Do not run drain lines, water lines or electrical wiring where they can interfere with or contact dishwasher motor or legs.

The location where the dishwasher will be installed must provide clearance between motor and flooring. Motor should not touch the floor.

Do not install dishwasher over carpeted flooring.

Shelter dishwasher and water lines leading to dishwasher against freezing. Damage from freezing is not covered by the warranty.

A side panel kit is available from your dealer for installing your dishwasher at the end of your cabinetry.

A moisture barrier accessory (Part Number 4396277) is available from your dealer for installing underneath the countertop.

Check location where dishwasher will be installed. The location must provide:

•easy access to water, electricity and drain.

•Convenient access for loading and unloading dishes. Corner locations require a 2" (5.1 cm) minimum clearance between the side of the dishwasher door and the wall or cabinet.

•square opening for proper operation and appearance.

•cabinet front perpendicular to floor.

•level floor. (If floor at front of opening is not level with floor at rear of opening, shims may be needed to level dishwasher.)

Helpful Tip: Be sure to accurately measure dimensions and ensure dishwasher is level if the floor in the dishwasher opening is uneven (example: flooring extends only partway into opening).

NOTE: To avoid shifting during dishwasher operation, shims must be securely attached to the floor.

If dishwasher will be left unused for a period of time or in a location where it may be subject to freezing, have it winterized by authorized service personnel.

Make sure pipes, wires and drain hose are within the shaded area shown in the “Product and Cabinet Opening Dimensions” section.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Table of Contents Table des matières W10282553A You Need to Table of ContentsLocation Requirements Tools and PartsMinimum, measured from narrowest point of opening Product and Cabinet Opening DimensionsUse of air gap Drain RequirementsWater Supply Requirements Electrical RequirementsPrepare Cabinet Opening-New Utilities Prepare Cabinet Opening-Existing UtilitiesPrepare and Route Water Line Install Drain Hose No waste disposer no air gap Connect drain hoseWaste disposer with air gap Waste disposer no air gapPrepare Dishwasher Power Cord-Connect remaining wires Make Power Supply Cord ConnectionPower Cord-Route cord into terminal box Power Supply Cord- Connect ground wireDetermine Cabinet Opening Move Dishwasher into Cabinet Opening Choose Attachment OptionMove dishwasher into cabinet opening Check water and drain hose positionOpen and close door Door falls open- Increase spring tensionConnect to Water Supply Connect to Drain Make Direct Wire Electrical ConnectionSlide clamp onto connector Direct Wire-Route cable into terminal boxDirect Wire-Reinstall terminal box cover Direct Wire-Connect ground wireDirect Wire-Connect remaining wires Direct Wire-Secure cable in conduit connectorSecure Dishwasher in Cabinet Opening Check lower panel edge Complete InstallationReinstall access panels Remove towel and replace lower dishwasher rackIf Dishwasher Does Not Operate Power supply cord-Plug into a grounded 3 prong outletReconnect power Check OperationPréparation de la cavité dencastrement Instructions d’installation suiteTable des matières Processus à appliquerOutillage et pièces Exigences d’emplacementDimensions Produit et cavité d’encastrement En gris sur les parois de la cavité d’encastrementMinimum à l’endroit le plus étroit de la cavité Utilisation d’un brise-vide Spécifications de l’évacuationSpécifications de l’alimentation en eau Spécifications électriquesQuel type de raccordement électrique sera utilisé? Déconnecter la source de courant électriqueFermer l’arrivée d’eau Moyens de raccordement aux divers circuits déjà existants?Câblage direct Acheminement du câble Cordon d’alimentation Préparation du trouCâblage direct Perçage du trou Câblage direct Préparation du trouPurge de la canalisation d’eau Installation du tuyau d’évacuationInstallation de la canalisation dalimentation Installation du tuyau d’évacuationPas de broyeur à déchets pas de brise-vide Raccordement du tuyau d’évacuationBroyeur à déchets pas de brise-vide Broyeur à déchets avec brise-videPréparation du lave-vaisselle Attachez l’isolationDépose des panneaux Cordon d’alimentation Conducteur de liaison à la terre Installation du serre-câbleRaccordement électrique Cordon d’alimentation Ôter le couvercle du boîtier De connexion électriqueTableau de réglage Hauteur du lave-vaisselle Dimensions de la cavité d’encastrementConfiguration de câblage Mesure des dimensionsChoix de l’option de fixation Manœuvre de la porte Déplacement du lave-vaisselle à proximité de louverturePlier la languette montage latéral Redresser le lave-vaisselleIsolant La tension des ressortsInsertion du lave-vaisselle dans la cavité d’encastrement Contrôle de l’aplomb et réglage des pieds si nécessaireRecherche de fuites Raccordement à la canalisation d’eauRaccordement à l’égout Raccorder le raccord coudé de 90 à la valveCâblage direct Raccordement des autres conducteurs Raccordement électrique Câblage directBride de tuyau position finale Câblage direct Acheminement jusqu’au boîtier de connexionCâblage direct Immobilisation dans le connecteur de conduit Extraction du panier inférieur utilisation d’une servietteSerrer les vis du serre-câble pour immobiliser le câble Achever linstallation Reconnecter la source de courant électrique Inspection de la rive de panneau inférieureSerrage des vis Reconnecter la source de courant électriqueHeures Contrôle du fonctionnementSi le lave-vaisselle ne fonctionne pas Conseils additionnels

W10282553A specifications

The Maytag W10282553A is a refrigerator water filter that plays a crucial role in maintaining the quality and taste of drinking water. This filter is designed specifically for select Maytag refrigerators, ensuring a seamless fit and optimal performance. With a focus on reliability and efficiency, the W10282553A provides several key features and technologies that promote clean and refreshing water.

One of the standout characteristics of the W10282553A is its advanced filtration system. The filter is designed to reduce contaminants such as chlorine taste and odor, lead, mercury, and other impurities that can affect the quality of drinking water. This ensures that every glass of water not only tastes pure but is also safe for consumption.

The installation process of the Maytag W10282553A is user-friendly, allowing homeowners to easily replace the filter without needing professional assistance. The filter is designed to be a direct replacement for compatible models, making it a convenient and practical choice for maintaining optimal refrigerator performance.

Another notable aspect of the W10282553A is its long-lasting performance. The filter typically lasts for up to six months or 200 gallons, depending on usage and water quality. This longevity makes it a cost-effective solution for households looking to enjoy clean and filtered water without frequent replacements.

In addition to its filtration capabilities, the Maytag W10282553A is an environmentally friendly option. By choosing filtered water over bottled water, consumers can reduce plastic waste and contribute to a healthier planet. The filter's design helps minimize the environmental impact while ensuring high-quality water for everyday use.

Furthermore, Maytag is a trusted brand known for its commitment to quality and durability. The W10282553A reflects this reputation, representing reliability and performance that consumers can count on. Ensuring fresh water access is vital for hydration and health, making the Maytag W10282553A an essential component of any compatible refrigerator.

In conclusion, the Maytag W10282553A refrigerator water filter offers advanced filtration technology, ease of installation, long-lasting performance, and environmental benefits. With its focus on providing clean and refreshing water, this filter is an indispensable accessory for maintaining a healthy lifestyle and the overall functionality of Maytag refrigerators.
Top Page Image Contents