Maytag W10282553A installation instructions Connect to Water Supply

Page 15

IMPORTANT: If wheels were removed, cover the floor when moving the dishwasher to avoid damage to the floor. Slowly move dishwasher completely into cabinet opening. Do not kink or pinch water line, drain hose, power supply cord or direct wire between dishwasher and cabinet. Remove cardboard from under dishwasher.

NOTE: It is all right if dishwasher fits tightly into cabinet opening. Do not remove insulation blanket – the blanket reduces the sound level.

NOTE: If using power cord, make sure to route end through hole in cutout before sliding into cabinet opening.

8 Align front of dishwasher with front of cabinet doors

Align front of dishwasher door panel with front of cabinet doors. You may need to adjust alignment to be even with your cabinets.

9 Check for plumb and adjust legs if needed

Check that leveling legs are firmly against the floor. Close and latch the door, and place level against the

front panel. Check that dishwasher is centered from front to back in the opening. If needed, adjust leveling leg until dishwasher is plumb. Repeat for other side of dishwasher.

Helpful Tip: Push up on front of dishwasher to raise dishwasher off the ground to adjust front legs. With some installations, it may be easier to adjust the front leg using the ³⁄₁₆" hex head socket or adjustable wrench.

Preferred method

Optional method

10 Check level side to side and adjust legs if needed

Place level against top front opening of tub. Check

that dishwasher is level from side to side. If dishwasher is not level, adjust front legs up or down until dishwasher is level.

Connect to Water Supply

1 Tighten 90° elbow fitting to valve

Be sure rubber washer is properly seated in fitting. Slide the ³⁄₄" fitting up to the valve and hand tighten to avoid unintentional cross-threading. Hand tighten until the coupling is tight. Using pliers, check the tightness of the coupling. An additional ¹⁄₄ to ¹⁄₂ turn may be required to seal the rubber gasket.

NOTE: Do not overtighten. Damage to the coupling can result.

2 Check for leaks

Place paper towel under 90° elbow fitting. Turn on water supply and check for leaks. If leak occurs, repeat previous step.

If needed, see website for animated representation

of this step. Visit www.whirlpool.com/watersupply under FAQ tab.

NOTE: Do not use Teflon † tape with compression fittings.

†is a registered trademark of E.I. Du Pont De Nemours and Company.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Table of Contents Table des matières W10282553A You Need to Table of ContentsLocation Requirements Tools and PartsMinimum, measured from narrowest point of opening Product and Cabinet Opening DimensionsUse of air gap Drain RequirementsWater Supply Requirements Electrical RequirementsPrepare Cabinet Opening-New Utilities Prepare Cabinet Opening-Existing UtilitiesPrepare and Route Water Line Install Drain Hose No waste disposer no air gap Connect drain hoseWaste disposer with air gap Waste disposer no air gapPrepare Dishwasher Power Cord-Connect remaining wires Make Power Supply Cord ConnectionPower Cord-Route cord into terminal box Power Supply Cord- Connect ground wireDetermine Cabinet Opening Move Dishwasher into Cabinet Opening Choose Attachment OptionMove dishwasher into cabinet opening Check water and drain hose positionOpen and close door Door falls open- Increase spring tensionConnect to Water Supply Connect to Drain Make Direct Wire Electrical ConnectionSlide clamp onto connector Direct Wire-Route cable into terminal boxDirect Wire-Reinstall terminal box cover Direct Wire-Connect ground wireDirect Wire-Connect remaining wires Direct Wire-Secure cable in conduit connectorSecure Dishwasher in Cabinet Opening Check lower panel edge Complete InstallationReinstall access panels Remove towel and replace lower dishwasher rackIf Dishwasher Does Not Operate Power supply cord-Plug into a grounded 3 prong outletReconnect power Check OperationPréparation de la cavité dencastrement Instructions d’installation suiteTable des matières Processus à appliquerOutillage et pièces Exigences d’emplacementDimensions Produit et cavité d’encastrement En gris sur les parois de la cavité d’encastrementMinimum à l’endroit le plus étroit de la cavité Utilisation d’un brise-vide Spécifications de l’évacuationSpécifications de l’alimentation en eau Spécifications électriquesQuel type de raccordement électrique sera utilisé? Déconnecter la source de courant électriqueFermer l’arrivée d’eau Moyens de raccordement aux divers circuits déjà existants?Câblage direct Acheminement du câble Cordon d’alimentation Préparation du trouCâblage direct Perçage du trou Câblage direct Préparation du trouPurge de la canalisation d’eau Installation du tuyau d’évacuationInstallation de la canalisation dalimentation Installation du tuyau d’évacuationPas de broyeur à déchets pas de brise-vide Raccordement du tuyau d’évacuationBroyeur à déchets pas de brise-vide Broyeur à déchets avec brise-videPréparation du lave-vaisselle Attachez l’isolationDépose des panneaux Cordon d’alimentation Conducteur de liaison à la terre Installation du serre-câbleRaccordement électrique Cordon d’alimentation Ôter le couvercle du boîtier De connexion électriqueTableau de réglage Hauteur du lave-vaisselle Dimensions de la cavité d’encastrementConfiguration de câblage Mesure des dimensionsChoix de l’option de fixation Manœuvre de la porte Déplacement du lave-vaisselle à proximité de louverturePlier la languette montage latéral Redresser le lave-vaisselleIsolant La tension des ressortsInsertion du lave-vaisselle dans la cavité d’encastrement Contrôle de l’aplomb et réglage des pieds si nécessaireRecherche de fuites Raccordement à la canalisation d’eauRaccordement à l’égout Raccorder le raccord coudé de 90 à la valveCâblage direct Raccordement des autres conducteurs Raccordement électrique Câblage directBride de tuyau position finale Câblage direct Acheminement jusqu’au boîtier de connexionCâblage direct Immobilisation dans le connecteur de conduit Extraction du panier inférieur utilisation d’une servietteSerrer les vis du serre-câble pour immobiliser le câble Achever linstallation Reconnecter la source de courant électrique Inspection de la rive de panneau inférieureSerrage des vis Reconnecter la source de courant électriqueHeures Contrôle du fonctionnementSi le lave-vaisselle ne fonctionne pas Conseils additionnels

W10282553A specifications

The Maytag W10282553A is a refrigerator water filter that plays a crucial role in maintaining the quality and taste of drinking water. This filter is designed specifically for select Maytag refrigerators, ensuring a seamless fit and optimal performance. With a focus on reliability and efficiency, the W10282553A provides several key features and technologies that promote clean and refreshing water.

One of the standout characteristics of the W10282553A is its advanced filtration system. The filter is designed to reduce contaminants such as chlorine taste and odor, lead, mercury, and other impurities that can affect the quality of drinking water. This ensures that every glass of water not only tastes pure but is also safe for consumption.

The installation process of the Maytag W10282553A is user-friendly, allowing homeowners to easily replace the filter without needing professional assistance. The filter is designed to be a direct replacement for compatible models, making it a convenient and practical choice for maintaining optimal refrigerator performance.

Another notable aspect of the W10282553A is its long-lasting performance. The filter typically lasts for up to six months or 200 gallons, depending on usage and water quality. This longevity makes it a cost-effective solution for households looking to enjoy clean and filtered water without frequent replacements.

In addition to its filtration capabilities, the Maytag W10282553A is an environmentally friendly option. By choosing filtered water over bottled water, consumers can reduce plastic waste and contribute to a healthier planet. The filter's design helps minimize the environmental impact while ensuring high-quality water for everyday use.

Furthermore, Maytag is a trusted brand known for its commitment to quality and durability. The W10282553A reflects this reputation, representing reliability and performance that consumers can count on. Ensuring fresh water access is vital for hydration and health, making the Maytag W10282553A an essential component of any compatible refrigerator.

In conclusion, the Maytag W10282553A refrigerator water filter offers advanced filtration technology, ease of installation, long-lasting performance, and environmental benefits. With its focus on providing clean and refreshing water, this filter is an indispensable accessory for maintaining a healthy lifestyle and the overall functionality of Maytag refrigerators.
Top Page Image Contents