Maytag W10282553A installation instructions Prepare Dishwasher

Page 10

Prepare Dishwasher

Tip Over Hazard

Do not use dishwasher until completely installed. Do not push down on open door.

Doing so can result in serious injury or cuts.

Excessive Weight Hazard

Use two or more people to move and install dishwasher.

Failure to do so can result in back or other injury.

1 Attach insulation

Tabs

Completed

Install

Using the precut slots in the insulation, fasten the insulation over the molded hooks on the tub. Be sure to fasten the insulation down on both sides of the tub.

2 Put dishwasher on its back

Helpful Tip: Place cardboard under dishwasher until installed in cabinet opening to avoid damaging floor covering. Do not use door panel as a worktable without first covering with a towel to avoid scratching the door panel.

Using two or more people, grasp sides of dishwasher door frame and place dishwasher on its back.

3 Remove panels

Using a ¹⁄₄" hex head socket, nut driver or Phillips screwdriver, remove the 2 screws attaching access panel and lower panel to dishwasher.

NOTE: Do not remove tech sheet from access panel.

4 Remove terminal box cover

Using a ¹⁄₄" hex head socket, nut driver or Phillips screwdriver, remove terminal box cover. Retain for later use.

5 Install strain relief

Install a UL Listed/CSA Approved strain relief. Make sure screwheads are facing to the left when tightening conduit nut. Strain relief may be provided with the power supply cord kit.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Table of Contents Table des matières W10282553A Table of Contents You Need toTools and Parts Location RequirementsProduct and Cabinet Opening Dimensions Minimum, measured from narrowest point of openingElectrical Requirements Drain RequirementsWater Supply Requirements Use of air gapPrepare Cabinet Opening-Existing Utilities Prepare Cabinet Opening-New UtilitiesPrepare and Route Water Line Install Drain Hose Waste disposer no air gap Connect drain hoseWaste disposer with air gap No waste disposer no air gapPrepare Dishwasher Power Supply Cord- Connect ground wire Make Power Supply Cord ConnectionPower Cord-Route cord into terminal box Power Cord-Connect remaining wiresDetermine Cabinet Opening Choose Attachment Option Move Dishwasher into Cabinet OpeningDoor falls open- Increase spring tension Check water and drain hose positionOpen and close door Move dishwasher into cabinet openingConnect to Water Supply Direct Wire-Route cable into terminal box Make Direct Wire Electrical ConnectionSlide clamp onto connector Connect to DrainDirect Wire-Secure cable in conduit connector Direct Wire-Connect ground wireDirect Wire-Connect remaining wires Direct Wire-Reinstall terminal box coverSecure Dishwasher in Cabinet Opening Remove towel and replace lower dishwasher rack Complete InstallationReinstall access panels Check lower panel edgeCheck Operation Power supply cord-Plug into a grounded 3 prong outletReconnect power If Dishwasher Does Not OperateProcessus à appliquer Instructions d’installation suiteTable des matières Préparation de la cavité dencastrementExigences d’emplacement Outillage et piècesEn gris sur les parois de la cavité d’encastrement Dimensions Produit et cavité d’encastrementMinimum à l’endroit le plus étroit de la cavité Spécifications électriques Spécifications de l’évacuationSpécifications de l’alimentation en eau Utilisation d’un brise-videMoyens de raccordement aux divers circuits déjà existants? Déconnecter la source de courant électriqueFermer l’arrivée d’eau Quel type de raccordement électrique sera utilisé?Câblage direct Préparation du trou Cordon d’alimentation Préparation du trouCâblage direct Perçage du trou Câblage direct Acheminement du câbleInstallation du tuyau d’évacuation Installation du tuyau d’évacuationInstallation de la canalisation dalimentation Purge de la canalisation d’eauBroyeur à déchets avec brise-vide Raccordement du tuyau d’évacuationBroyeur à déchets pas de brise-vide Pas de broyeur à déchets pas de brise-videAttachez l’isolation Préparation du lave-vaisselleDépose des panneaux Ôter le couvercle du boîtier De connexion électrique Installation du serre-câbleRaccordement électrique Cordon d’alimentation Cordon d’alimentation Conducteur de liaison à la terreMesure des dimensions Dimensions de la cavité d’encastrementConfiguration de câblage Tableau de réglage Hauteur du lave-vaisselleChoix de l’option de fixation Redresser le lave-vaisselle Déplacement du lave-vaisselle à proximité de louverturePlier la languette montage latéral Manœuvre de la porteContrôle de l’aplomb et réglage des pieds si nécessaire La tension des ressortsInsertion du lave-vaisselle dans la cavité d’encastrement IsolantRaccorder le raccord coudé de 90 à la valve Raccordement à la canalisation d’eauRaccordement à l’égout Recherche de fuitesCâblage direct Acheminement jusqu’au boîtier de connexion Raccordement électrique Câblage directBride de tuyau position finale Câblage direct Raccordement des autres conducteursExtraction du panier inférieur utilisation d’une serviette Câblage direct Immobilisation dans le connecteur de conduitSerrer les vis du serre-câble pour immobiliser le câble Achever linstallation Reconnecter la source de courant électrique Inspection de la rive de panneau inférieureSerrage des vis Reconnecter la source de courant électriqueConseils additionnels Contrôle du fonctionnementSi le lave-vaisselle ne fonctionne pas Heures

W10282553A specifications

The Maytag W10282553A is a refrigerator water filter that plays a crucial role in maintaining the quality and taste of drinking water. This filter is designed specifically for select Maytag refrigerators, ensuring a seamless fit and optimal performance. With a focus on reliability and efficiency, the W10282553A provides several key features and technologies that promote clean and refreshing water.

One of the standout characteristics of the W10282553A is its advanced filtration system. The filter is designed to reduce contaminants such as chlorine taste and odor, lead, mercury, and other impurities that can affect the quality of drinking water. This ensures that every glass of water not only tastes pure but is also safe for consumption.

The installation process of the Maytag W10282553A is user-friendly, allowing homeowners to easily replace the filter without needing professional assistance. The filter is designed to be a direct replacement for compatible models, making it a convenient and practical choice for maintaining optimal refrigerator performance.

Another notable aspect of the W10282553A is its long-lasting performance. The filter typically lasts for up to six months or 200 gallons, depending on usage and water quality. This longevity makes it a cost-effective solution for households looking to enjoy clean and filtered water without frequent replacements.

In addition to its filtration capabilities, the Maytag W10282553A is an environmentally friendly option. By choosing filtered water over bottled water, consumers can reduce plastic waste and contribute to a healthier planet. The filter's design helps minimize the environmental impact while ensuring high-quality water for everyday use.

Furthermore, Maytag is a trusted brand known for its commitment to quality and durability. The W10282553A reflects this reputation, representing reliability and performance that consumers can count on. Ensuring fresh water access is vital for hydration and health, making the Maytag W10282553A an essential component of any compatible refrigerator.

In conclusion, the Maytag W10282553A refrigerator water filter offers advanced filtration technology, ease of installation, long-lasting performance, and environmental benefits. With its focus on providing clean and refreshing water, this filter is an indispensable accessory for maintaining a healthy lifestyle and the overall functionality of Maytag refrigerators.
Top Page Image Contents