Maytag MGC6430 To Convert Appliance For Use With Natural Gas, Reset the Valves for Natural GAS

Page 10

To Convert Appliance For Use With Natural Gas

Electrical power and gas must be turned off prior to conversion.

If this appliance has been converted for use with LP gas, each of the following modifications must be performed to convert the unit back to natural gas.

A. REPLACE ALL ORIFICE SPUDS.

1.Perform Steps 1 and 2 on page 8.

2.Perform Step 3 on page 8.

3.For Step 4: Locate the brass natural gas orifice spuds that were originally installed in this appliance before its conversion for use with LP gas. Observe the number on each of the spuds and note the correct burner location for each spud as shown in figures 14 and 15.

Installation Of Natural Gas Orifice Spuds

5BURNER MODEL (36￿ WIDE)

1.551.071.42

1.421.61

FIGURE 14

4 BURNER MODEL (30￿ WIDE)

1.42

1.07

 

1.421.61

FIGURE 15

4.Complete Steps 5, 6 and 7 on page 8 to complete the installation of natural gas main spuds in their correct locations.

5.Save the orifices removed from the appliance for future use. They will be needed if this appliance is again converted for use with LP gas.

B.INVERT CAP IN APPLIANCE PRESSURE REGULATOR. (See figure 11).

With the appliance installed the appliance regulator should be located as shown in either figure 3, 4 or 5 (pages 4, 5 & 6). Identify the type of appliance regulator and follow the instructions in the appropriate illustration.

C.RESET THE VALVES FOR NATURAL GAS

1.Light one burner, and set on low.

2.Remove the knob.

3.Remove the rubber grommets if necessary.

4.Locate the valve adjustment screw. If necessary align hole in switch cover with adjustment screw. See figure 12.

5.Insert a slender, thin-blade screwdriver into knob hole and engage blade with slot in adjusting screw.

6.Starting from the LP position (see #5 on page 9, under C. LOW FLAME ADJUSTMENT), turn the screw counter clockwise until the flame stabilizes and matches the pictured “low” setting on figure 13. Proper adjustment will produce a stable, steady blue flame of minimum size. The final adjustment should be checked by turning the knob from high to low several times without extinguishing the flame.

After Steps A, B and C have been completed, check the appearance of each burner’s flame at the Hi and Lo settings against figure 13. If the flames appear too large or too small, make sure all steps were completed correctly.

10

Image 10
Contents 8101P595-60 Cutout Dimensions Are CriticalDimensions InchesLocation Of Your Maytag Appliance Installing Cabinetry Over Your Maytag CooktopRequired Adjustments At Time Of Installation Preparation Of CountertopRecreational Park Trailers Installation Of ApplianceMobile Homes Commonwealth Of MassachusettsIf no Other Appliance is to be Installed below this Cooktop Connecting Appliance To Gas SupplyIllustrative GAS Supply Piping Wall Oven Installed below 30 Cooktop Pressure Testing Illustrative Alternative PipingElectrical Wiring Information Electrical Grounding InstructionsRemoval of Orifice Spud Installation Of LP Orifice SpudConverting Appliance For Use With LP Gas Replace ALL Orifice SpudsConversion of Appliance Pressure Regulator LOW Flame Adjustment See figureInvert CAP in Appliance Pressure Regulator See figure To Convert Appliance For Use With Natural Gas Installation Of Natural Gas Orifice SpudsReset the Valves for Natural GAS Invert CAP in Appliance Pressure REGULATOR. See figureBurner Performance High Altitude NoticeDimensiones PulgadasSugerencias importantes de preparación Ubicación de su electrodoméstico MaytagPreparación de la superficie para cocinar Ajustes necesarios al momento de la instalaciónInstalación del electrodoméstico Casas móvilesRemolques de recreación En la Commonwealth de MassachusettsConexión del electrodoméstico al suministro de gas Ilustración DE LA Tubería DE Suministro DE GASNota, en referencia a la Figura 4, anterior Pruebas de presión Ilustración DE LA Tubería AlternativaInformación de alambrado eléctrico Instrucciones eléctricas de conexión TierraInstalación de la copa de orificio LP Para Quitar LA Copa DE OrificioReemplace Todas LAS Copas DE Orificio Inversión DE LA Tapa DEL Regulador DE Presión Vea la figura Conversión DELRegulador DE Presión Ajuste DE LA Llama Baja Vea la figuraInvierta LA Tapa DEL Regulador DE PRESIÓN. Vea la figura Instalación de las copas de orificio de gas NaturalReajuste LAS Válvulas Para GAS Natural Desempeño de los quemadores Aviso de altitudManuel DE PoucesPréparation du comptoir Emplacement de votre appareil ménager MaytagRéglages requis lors de la mise en service Suggestions importantes pour la préparationPose de l’appareil Maisons mobilesRoulottes de parc Dans le Commonwealth du MassachusettsRaccordement de l’appareil à l’alimentation en gaz Illustration D’UNE Conduite DE GAZFour Mural Monté Sous LA Plaque DE Cuisson DE 30 PO 76,2 CMVérification de la pression Illustration D’UNE Méthode AlternativeCâblage électrique Mise à la terrePose de l’écrou à orifice pour gaz GPL Conversion de l’appareil au gaz GPLDépose DE L’ÉCROU À Orifice Remplacer Tous LES Raccords À OrificeInverser LE Capuchon Dans LE Détendeur Conversion DUDétendeur DE L’APPAREIL Réglage DE LA Flamme À FEU Doux Voir figurePose de raccords à orifice pour gaz naturel Régler LES Boutons DE Commande AU GAZ NaturelPour convertir l’appareil au gaz naturel Inverser LE Capuchon Dans LE Détendeur voir la figureFonctionnement des brûleurs Utilisation en haute altitude
Related manuals
Manual 11 pages 50.39 Kb

MGC6536, MGC6430 specifications

The Maytag MGC6430 and MGC6536 represent the forefront of modern cooking appliances, seamlessly combining style, functionality, and technology. Designed for those who appreciate both aesthetics and performance, these gas cooktops are a perfect addition to any kitchen.

Starting with the Maytag MGC6430, this model features a sleek and compact design that fits neatly into any countertop. Its powerful burners, including a 15,000 BTU burner, deliver high heat for searing meats and boiling water quickly. This cooktop also includes an additional simmer burner, which provides a gentle heat perfect for delicate sauces and melting chocolate. The cast iron grates offer a sturdy and attractive surface, allowing for smooth movement of pots and pans.

The MGC6536 takes the features of the MGC6430 a step further with a more expansive layout, featuring 5 burners that provide ample cooking space. One highlight is the powerful dual-flame burner that adjusts between high and low settings, giving chefs complete control over their cooking temperature. This model is equipped with a precise simmer burner as well, enhancing versatility when preparing meals that require careful attention to temperature.

Both models come standard with Maytag’s signature Power burners, designed to deliver quick heating and reduce cooking time. This unique technology allows home cooks to achieve professional results without the complexity of professional restaurant equipment. The cooktops also feature easy-to-clean surfaces, making post-cooking cleanup hassle-free. The sealed burners contain spills and messes, while the premium materials ensure that the surfaces maintain their appearance over time.

In terms of safety, both the MGC6430 and MGC6536 include electronic ignition systems, ensuring that the burners ignite quickly and reliably without the need for matches. They also offer a convenient control panel, strategically placed at the front for easy access, allowing for precise adjustments even while cooking.

Energy efficiency is another characteristic of these Maytag gas cooktops, enabling cooks to maximize their culinary experience while minimizing energy consumption. The combination of powerful burners and efficient design makes these cooktops a wise choice for environmentally conscious consumers.

Overall, the Maytag MGC6430 and MGC6536 gas cooktops encapsulate the essence of quality and innovation in kitchen appliances. With their blend of power, precision, and style, they are designed to elevate cooking experiences for home chefs and food enthusiasts alike.