Bunn LCC-2, LCA-2 Field Calibrating the Hot Water Flow Rate, Oz/sec 53 ml/sec w/ flow restrictor

Page 30

Field Calibration of the Concentrate Pumps / Dispenser Flow Rates

(Continued)

Dispenser Flow Rate Calibration

13.Press Down Arrow Key to display the CAL LF WTR FLO menu screen.

14.Place a 64 Oz (2000 ml) graduated container under Left Dispense Tip and Pull the Left Dispense Handle momentarily. The dispenser will dispense water for 20 seconds and then shut OFF automatically.

15.Keep the graduated container under dispense tip until all the water stops dripping.

16.Measure the volume of water collected in the graduated container.

Acceptable ranges for the volume collected

_____Dispenser Flow Rate___________

____Volume Collected____

1.8 Oz/sec (53 ml/sec) w/ flow restrictor

32

- 38

Oz, (946 - 1124 ml)

2.5 Oz/sec (74 ml/sec) w/o flow restrictor

46

- 52

Oz ,(1360 - 1538 ml)

17.If the amount collected is not within the acceptable range, empty the graduated container and repeat STEPS 14 – 16

18.If the amount collected is still not within range, inspect the dispense valves, tubing and mix chamber for lime, kinks or other obstructions.

19.When satisfied with the volume of concentrate collected, press the Down Arrow Key.

20.The CAL LF WTR VOL screen will be displayed. Use the (-) / (+) keys to adjust number displayed to the amount measured in STEP 16.

21.Press Down Arrow Key again to exit the CAL LEFT SIDE functions.

Calibrating the Right Side Dispenser

Repeat STEPS 1-21 above for the “CAL RIGHT SIDE” menus.

Field Calibrating the Hot Water Flow Rate

1.Locate the programming module and use the Arrow Down key to scroll through the LCD screen until “CAL HOT WTR FLO?” appears.

2.Place a 64 Oz (2000 ml) graduated container under Hot Water Tip and press the hot water switch. The unit will dispense Hot Water for 20 seconds and then shut OFF automatically. Keep the graduated container under the dispense tip until all the water stops dripping.

3.Measure the volume of water collected in the graduated container. The acceptable range for the volume collected is 32 - 38 Oz. (946 - 1124 ml).

4.If the amount collected is not within the acceptable range, empty the container and repeat steps 2 & 3.

5.If the amount collected is still not within range, inspect the hot water valve, tubing and fittings for lime, kinks, or other obstructions.

6.When satisfied with the volume of concentrate collected, press the Down Arrow Key.

7.The “CAL HOT WTR VOL” screen will be displayed. Use the (-) / (+) keys to adjust number displayed to the ammount measured in step 3.

8.Press Down Arrow Key again to exit this function.

30

34766 120105

 

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Post Office BOX SPRINGFIELD, Illinois Phone 217 529-6601 FAX 217Contents BUNN-O-MATIC Commercial Product Warranty00656.0000 IntroductionUser Notices 28181.0003Models with Master ON/OFF Switch Field Wiring Terminal Block DiagramModels without Master ON/OFF Switch Electrical RequirementsElectrical HOOK-UP Plumbing RequirementsInitial SET-UP Plumbing HOOK-UPSetting Dispenser Flow Rate Removing the restrictorsReprogramming the Dispenser Flow Rate Rate Selecting the Correct Pump TubingDispense Oz/sec 16 I.D. TubingOperating Controls and Interface 1513Initial Fill & Heat FlavorGard Feature Rinse Alarm FeatureAlarm Mode BIB Empty Lockout Feature Brew Temperature Lockout Feature351 + Programming the DispenserMenu Screen Action Description Tank Temp Exit 3/16Menu Screen Lock Flavor ? Exit YES Flavors Locked LF Disp VolumeRT Disp Volume 0oz +Ready Temp Menu Screen Tank TempExit + Cabinet TempBrew Lockout ? No Exit YES Menu ScreenRinse Lockout ? No Exit YES Action DescriptionCAL RT WTR Flow Pull Dispenser Menu Screen ActionCAL Right Pump ? Pull Dispenser CAL Right Side ? Exit YESTest LED’S ? No Exit YES Test Switches ? WTR Start DelayWTR Stop Delay Factory Defaults No YES Action DescriptionLoading the Concentrate Priming the Concentrate LinesOperating the Pull & Hold Dispenser Filling Cambros or other large containersOperating the Preset Portion Control Dispenser Models LCA-2 PC, LCA-2C PC, LCA-2A PCDaily Parts Washing Cleaning & Preventative MaintenanceGeneral Cleaning and Sanitizing Procedures Daily Rinsing Weekly SanitizingReplacing the Pump Tubing Draining the HOT Water Tank Troubleshooting Power LED OFFFront Panel LED Display Messages Concentrate BIB is Empty Internal FaultLeft Refill LED on Empty BIB WarningTubing kinked or blocked Check Tubing installation Troubleshooting Dispenser Diagnostics-LCD DisplayBIB Not properly connected Check BIB Connector Fittings Possible CauseScreen Displayed Possible Cause RPM Sensor failure Service Required Evaporator temperature too high Service RequiredMotor failure Service Required Cabinet circulating fan failure Service RequiredCalibrating the Left Side Dispenser Oz/sec 74 ml/sec w/o flow restrictor Field Calibrating the Hot Water Flow RateOz/sec 53 ml/sec w/ flow restrictor Calibrating the Right Side DispenserField Calibrating the Empty BIB Warning Calibrating The Empty BIB ThresholdLCA-2/LCA-2, PC/LCA-2C/LCA-2C, PC/LCC-2/LCC-2C Schematic Wiring Diagram Schematic Wiring Diagram LCC-2A/LCA-2A/LCA-2A, PC
Related manuals
Manual 36 pages 62.09 Kb Manual 26 pages 22.61 Kb

LCA-2 PC, LCA-2, LCC-2 specifications

The Bunn LCC-2, LCA-2 PC, and LCA-2A are high-performance commercial coffee brewers designed to meet the demands of busy coffee shops, restaurants, and other food service establishments. These machines are known for their efficiency, durability, and advanced brewing technologies, making them popular choices in the industry.

Starting with the Bunn LCC-2, this brewer is recognized for its compact design and ease of use. It has a brewing capacity of up to 3.8 gallons per hour, ensuring that coffee is ready quickly during peak hours. The LCC-2 uses a pour-over brewing method, which means that water is heated to the ideal brewing temperature and then poured over coffee grounds for optimal extraction. One of its standout features is the digital temperature control, which allows operators to adjust brewing temperatures easily for different coffee types. Additionally, the Bunn LCC-2 features a stainless steel construction that enhances durability and provides a sleek look for any commercial kitchen.

Moving on to the Bunn LCA-2 PC, this model includes programmable capabilities, making it perfect for establishments that require consistency and convenience. The LCA-2 PC allows users to preset brewing schedules and customize brew cycles, ensuring that each pot of coffee meets specific flavor profiles. This model is designed with a large-capacity brewing system that can produce up to 7.5 gallons of coffee per hour, making it an ideal choice for high-demand environments. It also boasts a built-in hot water faucet, which provides instant hot water for other beverages or culinary applications. The LCA-2 PC's advanced brewing automation helps maintain optimal brew quality while minimizing waste.

Lastly, the Bunn LCA-2A is an advanced version that focuses on automation and efficiency. This brewer features a state-of-the-art digital brew timer, which allows precise control over brew times, leading to consistent flavor extraction. The LCA-2A also integrates with Bunn’s patented brewWISE technology, which tracks brew recipes and monitors performance. The intuitive interface allows for easy operation, even for staff who may be less experienced with coffee brewing. With a capacity of up to 4 gallons per hour and a durable stainless steel frame, the LCA-2A ensures longevity while delivering exceptional coffee.

In summary, the Bunn LCC-2, LCA-2 PC, and LCA-2A represent the pinnacle of commercial coffee brewing technology. Their unique features, including programmable settings, large brewing capacities, and durable constructions, cater to the diverse needs of the food service industry. Each model emphasizes convenience, flexibility, and quality, making them invaluable assets in any professional coffee environment.
Top Page Image Contents