Bunn FMD-5 Product overflows container Dispense Switch, Noises On the counter top Water Supply

Page 10

TROUBLESHOOTING (cont.)

 

 

 

 

PROBLEM

PROBABLE CAUSE

REMEDY

 

Product overflows container

1. Dispense Switch

Refer to Service - Dispense Switch for

 

 

 

testing procedures. See page 28

 

2.

Dispense Solenoid Valve

Remove the solenoid valve and clear

 

 

 

any obstructions. Rebuild or replace

 

 

 

the valve if necessary. See page 47

Dispenser is making unusual

1. Plumbing Lines

Plumbing lines should not be resting

noises

 

 

on the counter top.

 

2.

Water Supply

(A) The dispenser must be connected

 

 

 

to a cold water line

 

 

 

(B) Water pressure to the dispenser

 

 

 

must not exceed 90 psi (620 kPa).

 

 

 

Install a regulator if necessary to

 

 

 

lower the working pressure to ap-

 

 

 

proximately 50 psi (345 kPa).

 

3.

Tank Heater

Remove and clean lime off the tank

 

 

 

heater. See page 50

Excess dust

1. Fan

Refer to Service

- Fan for testing

 

 

 

procedures. See page 32

 

2.

A) Hopper Drive Board - FMD-1

Refer to Service - Hopper Drive

 

 

 

Board for testing procedures. See

 

 

 

page 35

 

 

 

B) Control board

Refer to Service - Control Board for

 

 

 

testing procedures. See page 20

Display not lit

1. Lamp

Refer to Service -

Lamp, see page

 

 

 

39 for lamp replacement.

 

2.

Lamp Holder

Refer to Service - Lamp Holder for

 

 

 

testing procedures. See page 39

 

3.

Starter - Lamp

Refer to Service - Starter for testing

 

 

 

procedures. See page 40

 

4.

Ballast

Refer to Service - Ballast for testing

 

 

 

procedures. See page 19

10

42672 122209

 

Page 9 Page 11
Image 10
Page 9 Page 11
Contents FMD Series Phone 217 529-6601 FAX 217BUNN-O-MATIC Commercial Product Warranty Excluding regular maintenance itemsIntroduction Cleaning Required Regular Maintenance Problem Probable Cause Level Control Board and Probe FMD-1 ProblemProduct will not dispense RemedyProblem Probable Cause Remedy Troubleshooting Excess dust Fan Refer to Service Product overflows container Dispense SwitchInstall a regulator if necessary to Procedures. See42672 Component Access 20,23SERVICEcont Access PanelsTest Procedures Auger Motor Service Auger Drive Components all ModelsLocation Spacer Auger Motor Hopper Base Dust Seal Washer ServiceAuger Drive Components Retainer Clip Panel RED to Control BoardBushing Panel Auger Drive Shaft Remove auger drive shaft bushing from hopperRinse and dry each item thoroughly Locknut Auger Motor BracketAuxillary Control Board FMD DBC-3 only Service Auxillary Control Board Disconnect the dispenser from the power sourceService Ballast all ModelsTest Procedure Power Supply Control BoardCheck that the RINSE/RUN switch is in the Rinse position Hopper Motor Control CircuitryControl Board Using four #6-32 keps nutsConnectors on the control board Control board to the component bracketControl Board Check that the rinse/run switch is in the run posi- tion Control Board Connectors Location Remove temperature probe from the tankRemove bulb from the tank BLK to Main Control ThermostatWHI to Main If voltage is present as described, proceed to #6 Open the dispenser door and remove the bottom door coverIf voltage is present as described, proceed to #7 FMD DBC-3 Digital Touch Control Switch FMD DBC-2,DBC-3FMD DBC-2FD Digital Touch Control Switch ConnectorsEMI Filter 230 Volt FMD DBC-3 EMI FilterDisconnect the black and white wires from the fan terminals Test ProceduresVacuum FAN all Models Frother and Whipper Motor all Models except -2FD Frother and Whipper MotorFrother and Whipper Motor Will seat inside the whipper chamberHopper Drive Board FMD-1 only Hopper Drive BoardHopper Drive Board Terminals HOT/COLD Switch Optional for FMD DBC-3 Disconnect the wires from the switch terminalsTerminals Lamp Holder all Models Door Assy Upper Panel Lamp Holders Lower PanelLamp Starter and Socket Reconnect the violet wire to terminal Level Control Board and Level Probe FMD-1 onlyLevel Board Terminals Limit Thermostat all Models Limit ThermostatOverflow Protection Switch Rinse /RUN Switch all Models RINSE/RUN SwitchSolenoid Valve Cold Water Optional for FMD-2,-3,-4,-5 Cold Water Solenoid TerminalsSolenoid Valves Dispense all Models Dispense Solenoid Valves P1637.40 LocationHOT Water Dispense Solenoid Valve FMD-2FD,DBC-2FD,-3,DBC-3 Solenoid ValveSolenoid Valve Inlet all Models Inlet Solenoid ValveWHI or RED to Main BLK to Limit Wiring Harness Tank Heater all ModelsTank Heater Relay FMD-4,-5,120V Dispensers only BRN/BLK from WHI from Main HarnessTank Heater Switch all Models Tank Heater SwitchTransformer all Models Disconnected from the main wiring harnessRemove and discard the transformer Q5 & MOV4 Controls Right Whipper Motor Q1 & MOV1 Controls Left Whipper MotorQ2 & MOV3 Controls Center Whipper Motor Q7 & MOV2 Controls Refill ValveSchematic Wiring Diagram FMD-1 BLKSchematic Wiring Diagram FMD-1A WHI-16Schematic Wiring Diagram FMD-2 Schematic Wiring Diagram FMD-2A Schematic Wiring Diagram FMD DBC-2 Freeze Dried W/HOT Water Schematic Wiring Diagram FMD-2FD 42672 42672 42672 42672 Schematic Wiring Diagram FMD DBC-3 With HOT Water Dispense Schematic Wiring Diagram Fmda DBC-3 With HOT Water Dispense 42672 42672 42672 42672 Schematic Wiring Diagram FMD-5A
Related manuals
Manual 45 pages 45.11 Kb Manual 29 pages 51.18 Kb

FMD-4, FMD-5 specifications

The Bunn FMD-5 is a state-of-the-art coffee dispenser designed specifically for high-volume coffee brewing situations. This machine is ideal for restaurants, convenience stores, and other establishments that require an efficient and reliable coffee dispensing solution.

One of the primary features of the Bunn FMD-5 is its ability to brew and serve fresh, hot coffee with exceptional speed. The unit is capable of dispensing up to five gallons of coffee per hour, making it an ideal choice for busy environments where customer demand is high. The system utilizes a digital brewer control that allows for precise brewing temperatures and times, ensuring consistency in flavor and quality.

The FMD-5 also incorporates advanced technologies to streamline the brewing process. It features a programmable control panel that allows users to adjust settings based on their specific needs. This includes the ability to set brew cycles, control brew levels, and even program different brew strengths. The easy-to-read digital display shows real-time information, making it simple for operators to monitor the brewing process.

Another notable characteristic of the Bunn FMD-5 is its compact and space-saving design. Despite its robust brewing capacity, the unit is designed to fit easily in various retail and foodservice environments. The machine is also built with durable materials, ensuring longevity and reliability under heavy usage.

For maintenance, the FMD-5 is designed with user convenience in mind. It features removable components and accessible areas for easy cleaning and routine maintenance. Users can also benefit from preventative maintenance features that monitor the machine’s performance, alerting operators to any potential issues before they escalate.

In terms of versatility, the Bunn FMD-5 can accommodate different brewing systems and coffee types, allowing users to customize their offerings based on customer preferences. It supports pre-ground coffee and can also be adapted for different brewing styles, enhancing its usability in various coffee service environments.

Overall, the Bunn FMD-5 is an impressive combination of speed, efficiency, and flexibility, making it an excellent choice for any operation that demands high-quality coffee with minimal wait time. Whether you are serving a morning rush of customers or maintaining a steady stream of coffee through the day, the Bunn FMD-5 stands out as a reliable and efficient coffee dispensing solution.
Top Page Image Contents