Bunn FMD-5, FMD-4 manual Vacuum FAN all Models, Test Procedures

Page 32

SERVICE (cont.)

VACUUM FAN (all Models)

FMD DBC-3 shown

P4102.40

FIG. 22 FAN

Location:

The fan is located inside the dispenser housing on the right rear of the dispenser base plate.

Test Procedures:

1.Disconnect the dispenser from the power source.

2.Disconnect the black and white wires from the fan terminals.

3.With a voltmeter, check the voltage across the black and white wires. Connect the dispenser to the power source. The indication must be:

a)120 volts ac for two wire 120 volt, three wire 120/208 volt and 120/240 volt models.

b)240 volts ac for two wire 240 volt models.

c)230 volts ac for two wire 230 volt models.

If voltage is present as described, replace the fan.

If voltage is not present as described, refer to Wiring Diagrams and check the dispenser wiring harness.

Removal and Replacement:

1.Disconnect the vacuum hose from the fan.

2.Remove the two #8-32 locking screws securing the fan to the dispenser housing base plate.

3.Disconnect the wires from the fan terminals and discard the fan

4.Refer to schematic wiring diagrams when recon- necting the wires.

5.Install new fan using two #8-32 locking screws.

6.Reconnect the vacuum hose to the fan.

BLK from Main

 

WiringHarness

 

WHI from Main Wiring Harness

 

FIG. 23 FAN TERMINALS

P1507

 

32

42672 122209

 

Page 31 Page 33
Image 32
Page 31 Page 33
Contents FMD Series Phone 217 529-6601 FAX 217BUNN-O-MATIC Commercial Product Warranty Excluding regular maintenance itemsIntroduction Cleaning Required Regular Maintenance Problem Probable Cause Problem Product will not dispenseLevel Control Board and Probe FMD-1 RemedyProblem Probable Cause Remedy Troubleshooting Product overflows container Dispense Switch Install a regulator if necessary toExcess dust Fan Refer to Service Procedures. See42672 Component Access 20,23SERVICEcont Access PanelsLocation Service Auger Drive Components all ModelsTest Procedures Auger Motor Service Auger Drive ComponentsSpacer Auger Motor Hopper Base Dust Seal Washer Retainer Clip Panel RED to Control BoardRemove auger drive shaft bushing from hopper Rinse and dry each item thoroughlyBushing Panel Auger Drive Shaft Locknut Auger Motor BracketAuxillary Control Board FMD DBC-3 only Service Auxillary Control Board Disconnect the dispenser from the power sourceService Ballast all ModelsTest Procedure Power Supply Control BoardCheck that the RINSE/RUN switch is in the Rinse position Hopper Motor Control CircuitryUsing four #6-32 keps nuts Connectors on the control boardControl Board Control board to the component bracketControl Board Check that the rinse/run switch is in the run posi- tion Control Board Connectors Remove bulb from the tank Remove temperature probe from the tankLocation WHI to Main Control ThermostatBLK to Main If voltage is present as described, proceed to #7 Open the dispenser door and remove the bottom door coverIf voltage is present as described, proceed to #6 FMD DBC-2FD Digital Touch Control Switch FMD DBC-2,DBC-3FMD DBC-3 Digital Touch Control Switch ConnectorsEMI Filter 230 Volt FMD DBC-3 EMI FilterVacuum FAN all Models Test ProceduresDisconnect the black and white wires from the fan terminals Frother and Whipper Motor all Models except -2FD Frother and Whipper MotorFrother and Whipper Motor Will seat inside the whipper chamberHopper Drive Board FMD-1 only Hopper Drive BoardHopper Drive Board Terminals HOT/COLD Switch Optional for FMD DBC-3 Disconnect the wires from the switch terminalsTerminals Lamp Holder all Models Door Assy Upper Panel Lamp Holders Lower PanelLamp Starter and Socket Reconnect the violet wire to terminal Level Control Board and Level Probe FMD-1 onlyLevel Board Terminals Limit Thermostat all Models Limit ThermostatOverflow Protection Switch Rinse /RUN Switch all Models RINSE/RUN SwitchSolenoid Valve Cold Water Optional for FMD-2,-3,-4,-5 Cold Water Solenoid TerminalsSolenoid Valves Dispense all Models Dispense Solenoid Valves P1637.40 LocationHOT Water Dispense Solenoid Valve FMD-2FD,DBC-2FD,-3,DBC-3 Solenoid ValveSolenoid Valve Inlet all Models Inlet Solenoid ValveWHI or RED to Main BLK to Limit Wiring Harness Tank Heater all ModelsTank Heater Relay FMD-4,-5,120V Dispensers only BRN/BLK from WHI from Main HarnessTank Heater Switch all Models Tank Heater SwitchRemove and discard the transformer Disconnected from the main wiring harnessTransformer all Models Q1 & MOV1 Controls Left Whipper Motor Q2 & MOV3 Controls Center Whipper MotorQ5 & MOV4 Controls Right Whipper Motor Q7 & MOV2 Controls Refill ValveSchematic Wiring Diagram FMD-1 BLKSchematic Wiring Diagram FMD-1A WHI-16Schematic Wiring Diagram FMD-2 Schematic Wiring Diagram FMD-2A Schematic Wiring Diagram FMD DBC-2 Freeze Dried W/HOT Water Schematic Wiring Diagram FMD-2FD 42672 42672 42672 42672 Schematic Wiring Diagram FMD DBC-3 With HOT Water Dispense Schematic Wiring Diagram Fmda DBC-3 With HOT Water Dispense 42672 42672 42672 42672 Schematic Wiring Diagram FMD-5A
Related manuals
Manual 45 pages 45.11 Kb Manual 29 pages 51.18 Kb

FMD-4, FMD-5 specifications

The Bunn FMD-5 is a state-of-the-art coffee dispenser designed specifically for high-volume coffee brewing situations. This machine is ideal for restaurants, convenience stores, and other establishments that require an efficient and reliable coffee dispensing solution.

One of the primary features of the Bunn FMD-5 is its ability to brew and serve fresh, hot coffee with exceptional speed. The unit is capable of dispensing up to five gallons of coffee per hour, making it an ideal choice for busy environments where customer demand is high. The system utilizes a digital brewer control that allows for precise brewing temperatures and times, ensuring consistency in flavor and quality.

The FMD-5 also incorporates advanced technologies to streamline the brewing process. It features a programmable control panel that allows users to adjust settings based on their specific needs. This includes the ability to set brew cycles, control brew levels, and even program different brew strengths. The easy-to-read digital display shows real-time information, making it simple for operators to monitor the brewing process.

Another notable characteristic of the Bunn FMD-5 is its compact and space-saving design. Despite its robust brewing capacity, the unit is designed to fit easily in various retail and foodservice environments. The machine is also built with durable materials, ensuring longevity and reliability under heavy usage.

For maintenance, the FMD-5 is designed with user convenience in mind. It features removable components and accessible areas for easy cleaning and routine maintenance. Users can also benefit from preventative maintenance features that monitor the machine’s performance, alerting operators to any potential issues before they escalate.

In terms of versatility, the Bunn FMD-5 can accommodate different brewing systems and coffee types, allowing users to customize their offerings based on customer preferences. It supports pre-ground coffee and can also be adapted for different brewing styles, enhancing its usability in various coffee service environments.

Overall, the Bunn FMD-5 is an impressive combination of speed, efficiency, and flexibility, making it an excellent choice for any operation that demands high-quality coffee with minimal wait time. Whether you are serving a morning rush of customers or maintaining a steady stream of coffee through the day, the Bunn FMD-5 stands out as a reliable and efficient coffee dispensing solution.
Top Page Image Contents