Bunn FMD-5, FMD-4 manual Tank Heater Switch all Models

Page 52

SERVICE (cont.)

TANK HEATER SWITCH (all Models)

FMD DBC-3 shown

FIG. 54 TANK HEATER SWITCH

P1684.40

 

Location:

 

The tank heater switch located is inside the dispenser on the upper right of the whipper motor mounting panel.

Test Procedure:

1.Disconnect the dispenser from the power source.

2.Disconnect the black or white/brown wires from the main harness.

3.With the switch in the “ON” (lower) position check for continuity between the center and the upper

terminal. With the switch in the “OFF” (upper) position no continuity should be present between center and upper terminals.

If continuity is present as described, the heater “ON/ OFF” switch is operating properly.

If continuity is not present as described, replace the switch.

Removal and Replacement:

1.Refer to the hopper section in this manual and remove the hopper assemblies and the hopper support plate.

2.Remove the switch mounting nut on the front of the front panel.

3.Remove switch with wires attached from the rear of the front panel.

4.Remove the wires from the switch terminals and discard switch.

5.Refer to schematic wiring diagrams when recon- necting the wires.

5. Push new switch through hole in the front panel and secure with face nut.

7.Refer to the hopper section in this manual and install the hopper support plate and the hopper assemblies.

FIG. 55 TANK HEATER SWITCH TERMINALSP1219

52

42672 122209

 

Page 51 Page 53
Image 52
Page 51 Page 53
Contents FMD Series Phone 217 529-6601 FAX 217BUNN-O-MATIC Commercial Product Warranty Excluding regular maintenance itemsIntroduction Cleaning Required Regular Maintenance Problem Probable Cause Problem Product will not dispenseLevel Control Board and Probe FMD-1 RemedyProblem Probable Cause Remedy Troubleshooting Product overflows container Dispense Switch Install a regulator if necessary toExcess dust Fan Refer to Service Procedures. See42672 Component Access 20,23SERVICEcont Access PanelsTest Procedures Auger Motor Service Auger Drive Components all ModelsLocation Service Auger Drive ComponentsSpacer Auger Motor Hopper Base Dust Seal Washer Retainer Clip Panel RED to Control BoardRemove auger drive shaft bushing from hopper Rinse and dry each item thoroughlyBushing Panel Auger Drive Shaft Locknut Auger Motor BracketAuxillary Control Board FMD DBC-3 only Service Auxillary Control Board Disconnect the dispenser from the power sourceService Ballast all ModelsTest Procedure Power Supply Control BoardCheck that the RINSE/RUN switch is in the Rinse position Hopper Motor Control CircuitryUsing four #6-32 keps nuts Connectors on the control boardControl Board Control board to the component bracketControl Board Check that the rinse/run switch is in the run posi- tion Control Board Connectors Location Remove temperature probe from the tankRemove bulb from the tank BLK to Main Control ThermostatWHI to Main If voltage is present as described, proceed to #6 Open the dispenser door and remove the bottom door coverIf voltage is present as described, proceed to #7 FMD DBC-3 Digital Touch Control Switch FMD DBC-2,DBC-3FMD DBC-2FD Digital Touch Control Switch ConnectorsEMI Filter 230 Volt FMD DBC-3 EMI FilterDisconnect the black and white wires from the fan terminals Test ProceduresVacuum FAN all Models Frother and Whipper Motor all Models except -2FD Frother and Whipper MotorFrother and Whipper Motor Will seat inside the whipper chamberHopper Drive Board FMD-1 only Hopper Drive BoardHopper Drive Board Terminals HOT/COLD Switch Optional for FMD DBC-3 Disconnect the wires from the switch terminalsTerminals Lamp Holder all Models Door Assy Upper Panel Lamp Holders Lower PanelLamp Starter and Socket Reconnect the violet wire to terminal Level Control Board and Level Probe FMD-1 onlyLevel Board Terminals Limit Thermostat all Models Limit ThermostatOverflow Protection Switch Rinse /RUN Switch all Models RINSE/RUN SwitchSolenoid Valve Cold Water Optional for FMD-2,-3,-4,-5 Cold Water Solenoid TerminalsSolenoid Valves Dispense all Models Dispense Solenoid Valves P1637.40 LocationHOT Water Dispense Solenoid Valve FMD-2FD,DBC-2FD,-3,DBC-3 Solenoid ValveSolenoid Valve Inlet all Models Inlet Solenoid ValveWHI or RED to Main BLK to Limit Wiring Harness Tank Heater all ModelsTank Heater Relay FMD-4,-5,120V Dispensers only BRN/BLK from WHI from Main HarnessTank Heater Switch all Models Tank Heater SwitchTransformer all Models Disconnected from the main wiring harnessRemove and discard the transformer Q1 & MOV1 Controls Left Whipper Motor Q2 & MOV3 Controls Center Whipper MotorQ5 & MOV4 Controls Right Whipper Motor Q7 & MOV2 Controls Refill ValveSchematic Wiring Diagram FMD-1 BLKSchematic Wiring Diagram FMD-1A WHI-16Schematic Wiring Diagram FMD-2 Schematic Wiring Diagram FMD-2A Schematic Wiring Diagram FMD DBC-2 Freeze Dried W/HOT Water Schematic Wiring Diagram FMD-2FD 42672 42672 42672 42672 Schematic Wiring Diagram FMD DBC-3 With HOT Water Dispense Schematic Wiring Diagram Fmda DBC-3 With HOT Water Dispense 42672 42672 42672 42672 Schematic Wiring Diagram FMD-5A
Related manuals
Manual 45 pages 45.11 Kb Manual 29 pages 51.18 Kb

FMD-4, FMD-5 specifications

The Bunn FMD-5 is a state-of-the-art coffee dispenser designed specifically for high-volume coffee brewing situations. This machine is ideal for restaurants, convenience stores, and other establishments that require an efficient and reliable coffee dispensing solution.

One of the primary features of the Bunn FMD-5 is its ability to brew and serve fresh, hot coffee with exceptional speed. The unit is capable of dispensing up to five gallons of coffee per hour, making it an ideal choice for busy environments where customer demand is high. The system utilizes a digital brewer control that allows for precise brewing temperatures and times, ensuring consistency in flavor and quality.

The FMD-5 also incorporates advanced technologies to streamline the brewing process. It features a programmable control panel that allows users to adjust settings based on their specific needs. This includes the ability to set brew cycles, control brew levels, and even program different brew strengths. The easy-to-read digital display shows real-time information, making it simple for operators to monitor the brewing process.

Another notable characteristic of the Bunn FMD-5 is its compact and space-saving design. Despite its robust brewing capacity, the unit is designed to fit easily in various retail and foodservice environments. The machine is also built with durable materials, ensuring longevity and reliability under heavy usage.

For maintenance, the FMD-5 is designed with user convenience in mind. It features removable components and accessible areas for easy cleaning and routine maintenance. Users can also benefit from preventative maintenance features that monitor the machine’s performance, alerting operators to any potential issues before they escalate.

In terms of versatility, the Bunn FMD-5 can accommodate different brewing systems and coffee types, allowing users to customize their offerings based on customer preferences. It supports pre-ground coffee and can also be adapted for different brewing styles, enhancing its usability in various coffee service environments.

Overall, the Bunn FMD-5 is an impressive combination of speed, efficiency, and flexibility, making it an excellent choice for any operation that demands high-quality coffee with minimal wait time. Whether you are serving a morning rush of customers or maintaining a steady stream of coffee through the day, the Bunn FMD-5 stands out as a reliable and efficient coffee dispensing solution.
Top Page Image Contents