Bunn FMD-4, FMD-5 Product overflows container Dispense Switch, Weak product Water Temperature

Page 11

TROUBLESHOOTING (cont.)

 

 

PROBLEM

PROBABLE CAUSE

Product overflows container

1.

Dispense Switch

 

2.

Dispense Solenoid Valve

REMEDY

Refer to Service - Dispense Switch for testing procedures. See page 23

Remove the solenoid valve and clear any obstructions. Rebuild or replace the valve if necessary. See page 35

Weak product

1. Water Temperature

Place an empty container beneath

 

 

the dispense tip. Initiate a dispense

 

 

cycle and check the water tempera-

 

 

ture immediately below the dispense

 

 

tip with a thermometer. Reading

 

 

should be 180°F to 200°F (see ther-

 

 

mostat temperature settings decal

 

 

in USER NOTICES on page 3.)

2.Whipper Motor

3.Frother

4.Dispense Solenoid Valve

Refer to Service - Whipper Motor for testing procedure. See page 27

Refer to Service - Frother Compo- nents. See page 26

Refer to Service - Dispense Solenoid Valve for test procedures. See page 35

5.Auger Drive

6.Auger Spring

7.Auger Motor

8.Rinse/Run Switch

9.Rinse Timer

10.Relay (120V versions only)

11.Control Board #2 (120V versions only)

Refer to Service - Auger Drive Com- ponents. See page 13 & 15

Refer to Service - Auger Drive Com- ponents. See page 13 & 15

Refer to Service - Auger Drive Com- ponents. See page 13 & 15

Refer to Service - Rinse/Run Switch for test procedures. See page 32

Refer to Operation - Rinse Timer. See Page 5

Refer to Service - Relay for testing procedures. See page 40

Refer to Service - Control Board #2 for testing procedures. See page 22

11

35135 012103

 

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Phone 217 529-6601 FAX 217 Post Office BOX SPRINGFIELD, IllinoisFMD-4 BUNN-O-MATIC Commercial Product WarrantyIntroduction User NoticesFMD-4 FMD-5 00831.000028368.0000 Plumbing Requirements Initial SET-UPElectrical Requirements Electrical HOOK-UPDispenser USE Liquid Level Control Rinse TimersInitial Fill & Heat Running a Rinse SequenceHopper Motor Speed Programing CleaningAdjustments Cold Beverage SET-UP OptionalDraining the HOT Water Tank Probable Cause TroubleshootingProblem Product will not dispenseProbable Cause Remedy Leaks Problem Probable CauseStat for testing procedures. See Dripping from dispense tip Lime build-upTip with a thermometer. Reading Product overflows container Dispense SwitchWeak product Water Temperature Refer to Operation Rinse Timer. SeeTroubleshooting Problem Auger Drive Components FMD-4 ServiceComponent Access ContentsRetainer Clip Panel Hopper LidSpacer Auger Motor Hopper Base Dust Seal Washer Location Auger Drive Components FMD-4To the rear of the auger motor mounting panel Hopper Dust Seal Auger Drive Components FMD-4 & FMD-5Bushing Panel Auger Drive Shaft LocknutRemove dust seal 17 from auger motor Ballasts FMD-4 & FMD-5 Refer to and reconnect the wiresLocation Control ThermostatControl Board Control BoardService Control Board Connectors FMD-5 Dispense Switchs FMD-4 & FMD-5FMD-4 Dispense Switch Terminals Dispense SwitchesFAN FANComponents Frother and Whipper Motor FMD-4 shown & FMD-5Whipper Motor Terminals INCREASE/DECREASE Switch INCREASE/DECREASE SwitchDoor Assy Upper Panel Lamp Holders Lower Panel Lamp Replacement Refer to FigLamp Holders Lamp Starter and Socket Refer to Location Lamp Replacement Refer toLimit Thermostat Limit ThermostatBoard J2-3 RINSE/RUN SwitchBLK from Main Harness BRN/BLK to HOT/COLD Switch HOT/COLD Switch OptionalCold Water Solenoid Valve Solenoid Valve Cold Water OptionalDispense Solenoid Valve Dispense Solenoid Valve Terminals Solenoid Valve Dispense FMD-4 & FMD-5Inlet Solenoid Valve Solenoid Valve InletMain Harness Thermostat Tank HeaterTank Heater Switch If the resistance measures as described, proceed to step Tank Heater Relay 120V Dispensers onlyPull component bracket out the front of the dis WHI/GRN from TransformerRemove and discard the transformer WHI from BLK from Main HarnessSchematic Wiring Diagram FMD-4 Single PHASE, 60HZ Schematic Wiring Diagram FMD-5 Single PHASE, 60HZ
Related manuals
Manual 71 pages 4.56 Kb Manual 29 pages 51.18 Kb

FMD-4, FMD-5 specifications

The Bunn FMD-5 is a state-of-the-art coffee dispenser designed specifically for high-volume coffee brewing situations. This machine is ideal for restaurants, convenience stores, and other establishments that require an efficient and reliable coffee dispensing solution.

One of the primary features of the Bunn FMD-5 is its ability to brew and serve fresh, hot coffee with exceptional speed. The unit is capable of dispensing up to five gallons of coffee per hour, making it an ideal choice for busy environments where customer demand is high. The system utilizes a digital brewer control that allows for precise brewing temperatures and times, ensuring consistency in flavor and quality.

The FMD-5 also incorporates advanced technologies to streamline the brewing process. It features a programmable control panel that allows users to adjust settings based on their specific needs. This includes the ability to set brew cycles, control brew levels, and even program different brew strengths. The easy-to-read digital display shows real-time information, making it simple for operators to monitor the brewing process.

Another notable characteristic of the Bunn FMD-5 is its compact and space-saving design. Despite its robust brewing capacity, the unit is designed to fit easily in various retail and foodservice environments. The machine is also built with durable materials, ensuring longevity and reliability under heavy usage.

For maintenance, the FMD-5 is designed with user convenience in mind. It features removable components and accessible areas for easy cleaning and routine maintenance. Users can also benefit from preventative maintenance features that monitor the machine’s performance, alerting operators to any potential issues before they escalate.

In terms of versatility, the Bunn FMD-5 can accommodate different brewing systems and coffee types, allowing users to customize their offerings based on customer preferences. It supports pre-ground coffee and can also be adapted for different brewing styles, enhancing its usability in various coffee service environments.

Overall, the Bunn FMD-5 is an impressive combination of speed, efficiency, and flexibility, making it an excellent choice for any operation that demands high-quality coffee with minimal wait time. Whether you are serving a morning rush of customers or maintaining a steady stream of coffee through the day, the Bunn FMD-5 stands out as a reliable and efficient coffee dispensing solution.
Top Page Image Contents