Bunn FMD-5, FMD-4 service manual RINSE/RUN Switch, BLK from Main Harness BRN/BLK to, Board J2-3

Page 32

SERVICE (cont.)

RINSE/RUN SWITCH

J1

J2

J4

J3

J1

J2

J4

J3

P2635

FIG. 25 RINSE/RUN SWITCH

Location:

The rinse/run switch is located on the lower center of the whipper motor mounting panel.

Test Procedures:

1.Disconnect the dispenser from the power source.

2.Check for continuity between the center left ter- minal and left bottom terminal, also between the center right terminal and the right bottom termi- nal with the switch in the rinse position (upper). Check for continuity across the center left termi- nal and the top left terminal, also between center right terminal and the top right terminal with the switch in the run position (lower). Continuity must not be present when the switch is in the center position.

If continuity is present as described, the switch is operating properly.

If continuity is not present as described, replace the switch.

Removal and Replacement:

1.Open the dispenser door.

2.Remove the facenut securing the run/rinse switch to the whipper motor mounting panel.

3.Remove switch with wires attached from the back side of the whipper motor mounting panel.

4.Disconnect the wires from the switch and dis- card the switch.

5.Refer to Fig. 26 when connecting the wires to the new switch.

6.Install new switch with wires attached through the hole in the whipper motor mounting panel and secure with facenut.

BRN/BLK to

GRY to Control

Main Harness

Board J2-2

 

GRN to Control

 

Board J2-9

BLK from

 

Main Harness

 

BRN/BLK to

 

Main Harness

WHI/GRY to Control

 

 

Board J2-3

 

P1644

FIG. 26 RINSE/RUN SWITCH TERMINALS

32

35135 012103

 

Image 32
Contents Post Office BOX SPRINGFIELD, Illinois Phone 217 529-6601 FAX 217BUNN-O-MATIC Commercial Product Warranty IntroductionUser Notices FMD-4FMD-4 FMD-5 00831.000028368.0000 Initial SET-UP Electrical RequirementsElectrical HOOK-UP Plumbing RequirementsLiquid Level Control Rinse Timers Initial Fill & HeatRunning a Rinse Sequence Dispenser USECleaning AdjustmentsCold Beverage SET-UP Optional Hopper Motor Speed ProgramingDraining the HOT Water Tank Troubleshooting ProblemProduct will not dispense Probable CauseProbable Cause Remedy Problem Probable Cause Stat for testing procedures. SeeDripping from dispense tip Lime build-up LeaksProduct overflows container Dispense Switch Weak product Water TemperatureRefer to Operation Rinse Timer. See Tip with a thermometer. ReadingTroubleshooting Problem Service Component AccessContents Auger Drive Components FMD-4Retainer Clip Panel Hopper LidSpacer Auger Motor Hopper Base Dust Seal Washer Location Auger Drive Components FMD-4To the rear of the auger motor mounting panel Auger Drive Components FMD-4 & FMD-5 Bushing Panel Auger Drive ShaftLocknut Hopper Dust SealRemove dust seal 17 from auger motor Refer to and reconnect the wires Ballasts FMD-4 & FMD-5Control Thermostat LocationControl Board Control BoardService Control Board Connectors FMD-5 Dispense Switchs FMD-4 & FMD-5FMD-4 Dispense Switches Dispense Switch TerminalsFAN FANFrother and Whipper Motor FMD-4 shown & FMD-5 ComponentsWhipper Motor Terminals INCREASE/DECREASE Switch INCREASE/DECREASE SwitchDoor Assy Upper Panel Lamp Holders Lower Panel Lamp Replacement Refer to FigLamp Holders Lamp Replacement Refer to Lamp Starter and Socket Refer to LocationLimit Thermostat Limit ThermostatBoard J2-3 RINSE/RUN SwitchBLK from Main Harness BRN/BLK to HOT/COLD Switch Optional HOT/COLD SwitchSolenoid Valve Cold Water Optional Cold Water Solenoid ValveDispense Solenoid Valve Solenoid Valve Dispense FMD-4 & FMD-5 Dispense Solenoid Valve TerminalsSolenoid Valve Inlet Inlet Solenoid ValveTank Heater Main Harness ThermostatTank Heater Switch If the resistance measures as described, proceed to step Tank Heater Relay 120V Dispensers onlyPull component bracket out the front of the dis Transformer Remove and discard the transformerWHI from BLK from Main Harness WHI/GRN fromSchematic Wiring Diagram FMD-4 Single PHASE, 60HZ Schematic Wiring Diagram FMD-5 Single PHASE, 60HZ
Related manuals
Manual 71 pages 4.56 Kb Manual 29 pages 51.18 Kb

FMD-4, FMD-5 specifications

The Bunn FMD-5 is a state-of-the-art coffee dispenser designed specifically for high-volume coffee brewing situations. This machine is ideal for restaurants, convenience stores, and other establishments that require an efficient and reliable coffee dispensing solution.

One of the primary features of the Bunn FMD-5 is its ability to brew and serve fresh, hot coffee with exceptional speed. The unit is capable of dispensing up to five gallons of coffee per hour, making it an ideal choice for busy environments where customer demand is high. The system utilizes a digital brewer control that allows for precise brewing temperatures and times, ensuring consistency in flavor and quality.

The FMD-5 also incorporates advanced technologies to streamline the brewing process. It features a programmable control panel that allows users to adjust settings based on their specific needs. This includes the ability to set brew cycles, control brew levels, and even program different brew strengths. The easy-to-read digital display shows real-time information, making it simple for operators to monitor the brewing process.

Another notable characteristic of the Bunn FMD-5 is its compact and space-saving design. Despite its robust brewing capacity, the unit is designed to fit easily in various retail and foodservice environments. The machine is also built with durable materials, ensuring longevity and reliability under heavy usage.

For maintenance, the FMD-5 is designed with user convenience in mind. It features removable components and accessible areas for easy cleaning and routine maintenance. Users can also benefit from preventative maintenance features that monitor the machine’s performance, alerting operators to any potential issues before they escalate.

In terms of versatility, the Bunn FMD-5 can accommodate different brewing systems and coffee types, allowing users to customize their offerings based on customer preferences. It supports pre-ground coffee and can also be adapted for different brewing styles, enhancing its usability in various coffee service environments.

Overall, the Bunn FMD-5 is an impressive combination of speed, efficiency, and flexibility, making it an excellent choice for any operation that demands high-quality coffee with minimal wait time. Whether you are serving a morning rush of customers or maintaining a steady stream of coffee through the day, the Bunn FMD-5 stands out as a reliable and efficient coffee dispensing solution.