Bunn FMD-5 service manual Service, Component Access, Contents, Auger Drive Components FMD-4

Page 13

SERVICE

This section provides procedures for testing and replacing various major components used in this dispenser should service become necessary. Refer to Troubleshooting for assistance in determining the cause of any problem.

WARNING - Inspection, testing, and repair of electri- cal equipment should be performed only by qualified service personnel. The dispenser should be un- plugged when servicing, except when electrical tests are required and the test procedure specifically states to plug-in the dispenser.

COMPONENT ACCESS

WARNING - Disconnect the dispenser from the power source before the removal of any panel or the replace- ment of any component.

All components are accessible by opening the door, removal of the door panels, dispenser top cov- ers, hopper(s), hopper support plate, splash guard, splash panel w/drip tray, lower front access panel and rear access cover.

Refer to the contents listing for component loca- tion.

Contents

 

Auger Drive Components (FMD-4)

....................... 13

Auger Drive Components (FMD-5)

....................... 15

Ballast

18

Control Thermostat

19

Control Board

20

Dispense Switch

23

Fan

25

Frother

26

Increase/Decrease Switch

28

Lamp Holder

29

Lamp

29

Lamp Starter and Socket

30

Limit Thermostat

31

Rinse/Run Switch

32

Hot/Cold Switch-Optional

33

Solenoid (Cold Water - Optional)

34

Solenoid (Dispense)

35

Solenoid (Inlet)

37

Tank Heater

38

Tank Heater Switch

39

Tank Heater Relay

40

Transformer

41

Whipper Motor

27

Wiring Diagram

42-45

AUGER DRIVE COMPONENTS FMD-4

J1

J2

J4

J3

J1

J2

J4

J3

P2635

FIG. 1 AUGER DRIVE COMPONENTS

Location

The auger components are located inside the bottom part of the hopper except for the auger drive bracket, spacer and retaining clip, which are located on the outside rear of the hopper base. The auger motor is located on the lower right rear of the motor mounting panel. Refer to Fig. 2 for disassembly and assembly.

Test Procedures - Auger Motor

1.Disconnect the dispenser from the power source.

2.Disconnect the white/red wire and the white wire from the hopper speed control board.

3.Check the voltage across the white/red wire and the white wire with a voltmeter. With the rinse/ run switch in the run (lower) position, connect the dispenser to the power supply. The indica- tion must be :

a)120 volts ac for two wire 120 volt models.

b)120 volts ac for three wire 120/208 volt or 120/240 volt models.

4.Disconnect the dispenser from the power sup- ply.

If voltage is present as described, proceed to #5.

If voltage is not present as described, refer to the wir- ing diagram and check the dispenser wiring harness.

13

35135 012103

 

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Phone 217 529-6601 FAX 217 Post Office BOX SPRINGFIELD, IllinoisIntroduction BUNN-O-MATIC Commercial Product WarrantyUser Notices FMD-428368.0000 00831.0000FMD-4 FMD-5 Electrical Requirements Initial SET-UPElectrical HOOK-UP Plumbing RequirementsInitial Fill & Heat Liquid Level Control Rinse TimersRunning a Rinse Sequence Dispenser USEAdjustments CleaningCold Beverage SET-UP Optional Hopper Motor Speed ProgramingDraining the HOT Water Tank Problem TroubleshootingProduct will not dispense Probable CauseProbable Cause Remedy Stat for testing procedures. See Problem Probable CauseDripping from dispense tip Lime build-up LeaksWeak product Water Temperature Product overflows container Dispense SwitchRefer to Operation Rinse Timer. See Tip with a thermometer. ReadingTroubleshooting Problem Component Access ServiceContents Auger Drive Components FMD-4Spacer Auger Motor Hopper Base Dust Seal Washer Hopper LidRetainer Clip Panel To the rear of the auger motor mounting panel Auger Drive Components FMD-4Location Bushing Panel Auger Drive Shaft Auger Drive Components FMD-4 & FMD-5Locknut Hopper Dust SealRemove dust seal 17 from auger motor Ballasts FMD-4 & FMD-5 Refer to and reconnect the wiresLocation Control ThermostatControl Board Control BoardService Control Board Connectors FMD-4 Dispense Switchs FMD-4 & FMD-5FMD-5 Dispense Switch Terminals Dispense SwitchesFAN FANComponents Frother and Whipper Motor FMD-4 shown & FMD-5Whipper Motor Terminals INCREASE/DECREASE Switch INCREASE/DECREASE SwitchLamp Holders Lamp Replacement Refer to FigDoor Assy Upper Panel Lamp Holders Lower Panel Lamp Starter and Socket Refer to Location Lamp Replacement Refer toLimit Thermostat Limit ThermostatBLK from Main Harness BRN/BLK to RINSE/RUN SwitchBoard J2-3 HOT/COLD Switch HOT/COLD Switch OptionalCold Water Solenoid Valve Solenoid Valve Cold Water OptionalDispense Solenoid Valve Dispense Solenoid Valve Terminals Solenoid Valve Dispense FMD-4 & FMD-5Inlet Solenoid Valve Solenoid Valve InletMain Harness Thermostat Tank HeaterTank Heater Switch Pull component bracket out the front of the dis Tank Heater Relay 120V Dispensers onlyIf the resistance measures as described, proceed to step Remove and discard the transformer TransformerWHI from BLK from Main Harness WHI/GRN fromSchematic Wiring Diagram FMD-4 Single PHASE, 60HZ Schematic Wiring Diagram FMD-5 Single PHASE, 60HZ
Related manuals
Manual 71 pages 4.56 Kb Manual 29 pages 51.18 Kb

FMD-4, FMD-5 specifications

The Bunn FMD-5 is a state-of-the-art coffee dispenser designed specifically for high-volume coffee brewing situations. This machine is ideal for restaurants, convenience stores, and other establishments that require an efficient and reliable coffee dispensing solution.

One of the primary features of the Bunn FMD-5 is its ability to brew and serve fresh, hot coffee with exceptional speed. The unit is capable of dispensing up to five gallons of coffee per hour, making it an ideal choice for busy environments where customer demand is high. The system utilizes a digital brewer control that allows for precise brewing temperatures and times, ensuring consistency in flavor and quality.

The FMD-5 also incorporates advanced technologies to streamline the brewing process. It features a programmable control panel that allows users to adjust settings based on their specific needs. This includes the ability to set brew cycles, control brew levels, and even program different brew strengths. The easy-to-read digital display shows real-time information, making it simple for operators to monitor the brewing process.

Another notable characteristic of the Bunn FMD-5 is its compact and space-saving design. Despite its robust brewing capacity, the unit is designed to fit easily in various retail and foodservice environments. The machine is also built with durable materials, ensuring longevity and reliability under heavy usage.

For maintenance, the FMD-5 is designed with user convenience in mind. It features removable components and accessible areas for easy cleaning and routine maintenance. Users can also benefit from preventative maintenance features that monitor the machine’s performance, alerting operators to any potential issues before they escalate.

In terms of versatility, the Bunn FMD-5 can accommodate different brewing systems and coffee types, allowing users to customize their offerings based on customer preferences. It supports pre-ground coffee and can also be adapted for different brewing styles, enhancing its usability in various coffee service environments.

Overall, the Bunn FMD-5 is an impressive combination of speed, efficiency, and flexibility, making it an excellent choice for any operation that demands high-quality coffee with minimal wait time. Whether you are serving a morning rush of customers or maintaining a steady stream of coffee through the day, the Bunn FMD-5 stands out as a reliable and efficient coffee dispensing solution.
Top Page Image Contents